diff options
Diffstat (limited to 'docs/report/introduction/methodology_nat44.rst')
| -rw-r--r-- | docs/report/introduction/methodology_nat44.rst | 26 |
1 files changed, 12 insertions, 14 deletions
diff --git a/docs/report/introduction/methodology_nat44.rst b/docs/report/introduction/methodology_nat44.rst index ba12f7d49b..29b7dfdf24 100644 --- a/docs/report/introduction/methodology_nat44.rst +++ b/docs/report/introduction/methodology_nat44.rst @@ -128,15 +128,6 @@ NAT44det scenario tested: NAT44 Endpoint-Dependent ^^^^^^^^^^^^^^^^^^^^^^^^ -.. - TODO: Is it possible to test a NAT44ed scenario where the outside source - address and port is limited to just one value? - In theory, as long as every inside source address&port traffic - uses a different destination address&port, there will be no conflicts, - and we could use bidirectional stateless profiles. - Possibly, VPP requires some amount of outside source address&port - to remain unused for security reasons. But we can try to see what happens. - In order to excercise NAT44ed ability to translate based on both source and destination address and port, the inside-to-outside traffic varies also destination address and port. Destination port is the same @@ -154,13 +145,17 @@ Therefore, NAT44ed is benchmarked using following methodologies: - Unidirectional throughput using *stateless* traffic profile. - Connections-per-second using *stateful* traffic profile. - Bidirectional PPS (see below) using *stateful* traffic profile. +- Bidirectional throughput (see below) using *stateful* traffic profile. Unidirectional NAT44ed throughput tests are using TRex STL (Stateless) APIs and traffic profiles, but with packets sent only in inside-to-outside direction. Similarly to NAT44det, NAT44ed unidirectional throughput tests include a ramp-up phase to establish and verify the presence of required NAT44ed -binding entries. +binding entries. As the sessions have finite duration, the test code +keeps inserting ramp-up trials during the search, if it detects a risk +of sessions timing out. Any zero loss trial visits all sessions, +so it acts also as a ramp-up. Stateful NAT44ed tests are using TRex ASTF (Advanced Stateful) APIs and traffic profiles, with packets sent in both directions. Tests are run @@ -168,7 +163,9 @@ with both UDP and TCP/IP sessions. As both NAT44ed CPS (connections-per-second) and PPS (packets-per-second) stateful tests measure (also) session opening performance, they use state reset instead of ramp-up trial. -That is also the reason why PPS tests are not called throughput tests. +NAT44ed bidirectional throughput tests use the same traffic profile +as PPS tests, but also prepend ramp-up trials as in the unidirectional tests, +so the test results describe performance without session opening overhead. Associated CSIT test cases use the following naming scheme to indicate NAT44det case tested: @@ -182,15 +179,16 @@ NAT44det case tested: - udir-[mrr|ndrpdr|soak], unidirectional stateless tests MRR, NDRPDR or SOAK. -- Stateful: ethip4[udp|tcp]-nat44ed-h{H}-p{P}-s{S}-[cps|pps]-[mrr|ndrpdr] +- Stateful: ethip4[udp|tcp]-nat44ed-h{H}-p{P}-s{S}-[cps|pps|tput]-[mrr|ndrpdr] - [udp|tcp], UDP or TCP/IP sessions - {H}, number of inside hosts, H = 1024, 4096, 16384, 65536, 262144. - {P}, number of ports per inside host, P = 63. - {S}, number of sessions, S = 64512, 258048, 1032192, 4128768, 16515072. - - [cps|pps], connections-per-second session establishment rate or - packets-per-second average rate. + - [cps|pps|tput], connections-per-second session establishment rate or + packets-per-second average rate, or packets-per-second rate + without session establishment. - [mrr|ndrpdr], bidirectional stateful tests MRR, NDRPDR. Stateful traffic profiles |