aboutsummaryrefslogtreecommitdiffstats
path: root/docs/report/introduction/methodology_nat44.rst
diff options
context:
space:
mode:
Diffstat (limited to 'docs/report/introduction/methodology_nat44.rst')
-rw-r--r--docs/report/introduction/methodology_nat44.rst166
1 files changed, 166 insertions, 0 deletions
diff --git a/docs/report/introduction/methodology_nat44.rst b/docs/report/introduction/methodology_nat44.rst
new file mode 100644
index 0000000000..5dc558f029
--- /dev/null
+++ b/docs/report/introduction/methodology_nat44.rst
@@ -0,0 +1,166 @@
+Network Address Translation IPv4 to IPv4
+----------------------------------------
+
+NAT44 Prefix Bindings
+^^^^^^^^^^^^^^^^^^^^^
+
+NAT44 prefix bindings should be representative to target applications,
+where a number of private IPv4 addresses from the range defined by
+:rfc:`1918` is mapped to a smaller set of public IPv4 addresses from the
+public range.
+
+Following quantities are used to describe inside to outside IP address
+and port bindings scenarios:
+
+- inside-addresses, ports-per-inside-address, number of inside source
+ addresses (representing inside hosts) and number of TCP/UDP source
+ ports per inside source address.
+- outside-addresses, number of outside (public) source addresses
+ allocated to NAT44. The maximal number of ports-per-outside-address
+ usable for NAT is 64 512 (in non-reserved port range 1024-65535,
+ :rfc:`4787`).
+- sharing-ratio, equal to inside-addresses / outside-addresses.
+
+CSIT NAT44 tests are designed to take into account the maximum number of
+ports (sessions) required per inside host (inside-address) and at the
+same time to maximize the use of outside-address range by using all
+available outside ports. With this in mind, the following scheme of
+NAT44 sharing ratios has been devised for use in CSIT:
+
++--------------------------+---------------+
+| ports-per-inside-address | sharing-ratio |
++==========================+===============+
+| 63 | 1024 |
++--------------------------+---------------+
+| 126 | 512 |
++--------------------------+---------------+
+| 252 | 256 |
++--------------------------+---------------+
+| 504 | 128 |
++--------------------------+---------------+
+
+Initial CSIT NAT44 tests, including associated TG/TRex traffic profiles,
+are based on ports-per-inside-address set to 63 and the sharing ratio of
+1024. This approach is currently used for all NAT44 tests including
+NAT44det (NAT44 deterministic used for Carrier Grade NAT applications)
+and NAT44ed.
+
+..
+ .. TODO::
+
+ Note that in the latter case, due to overloading of (ouside-address,
+ outside-port) tuple for different endpoint destinations the actual
+ sharing ratio is likely to different, as it will depend on the
+ destination addresses used by NAT'ed flows.
+
+Private address ranges to be used in tests:
+
+- 192.168.0.0 - 192.168.255.255 (192.168/16 prefix)
+
+ - Total of 2^16 (65 536) of usable IPv4 addresses.
+ - Used in tests for up to 65 536 inside addresses (inside hosts).
+
+- 172.16.0.0 - 172.31.255.255 (172.16/12 prefix)
+
+ - Total of 2^20 (1 048 576) of usable IPv4 addresses.
+ - Used in tests for up to 1 048 576 inside addresses (inside hosts).
+
+NAT44 Session Scale
+~~~~~~~~~~~~~~~~~~~
+
+NAT44 session scale tested is govern by the following logic:
+
+- Number of inside addresses/hosts H[i] = (H[i-1] x 2^2) with H(0)=1 024, i = 1,2,3, ...
+
+ - H[i] = 1 024, 4 096, 16 384, 65 536, 262 144, 1 048 576, ...
+
+- Number of sessions S[i](ports-per-host) = H[i] * ports-per-inside-address
+
+ - ports-per-host = 63
+
++---+---------+------------+
+| i | hosts | sessions |
++===+=========+============+
+| 0 | 1 024 | 64 512 |
++---+---------+------------+
+| 1 | 4 096 | 258 048 |
++---+---------+------------+
+| 2 | 16 384 | 1 032 192 |
++---+---------+------------+
+| 3 | 65 536 | 4 128 768 |
++---+---------+------------+
+| 4 | 262 144 | 16 515 072 |
++---+---------+------------+
+
+NAT44 Deterministic
+^^^^^^^^^^^^^^^^^^^
+
+NAT44det throughput tests are using TRex STL (Stateless) API and traffic
+profiles, similar to all other stateless packet forwarding tests like
+ip4, ip6 and l2, sending UDP packets in both directions
+inside-to-outside and outside-to-inside. See
+:ref:`data_plane_throughput` for more detail.
+
+NAT44det translation entries are created during the ramp-up phase
+preceding the throughput test, followed by verification that all entries
+are present, before proceeding to the throughput test. This ensures
+session setup does not impact the forwarding performance test.
+
+Associated CSIT test cases use the following naming scheme to indicate
+NAT44det scenario tested:
+
+- ethip4udp-nat44det-h{H}-p{P}-s{S}-[mrr|ndrpdr|soak]
+
+ - {H}, number of inside hosts, H = 1024, 4096, 16384, 65536, 262144.
+ - {P}, number of ports per inside host, P = 63.
+ - {S}, number of sessions, S = 64512, 258048, 1032192, 4128768,
+ 16515072.
+ - [mrr|ndrpdr|soak], MRR, NDRPDR or SOAK test.
+
+NAT44 Endpoint-Dependent
+^^^^^^^^^^^^^^^^^^^^^^^^
+
+NAT44ed is benchmarked using following methodologies:
+
+- Uni-directional throughput using *stateless* traffic profile.
+- Connections-per-second using *stateful* traffic profile.
+- Bi-directional throughput using *stateful* traffic profile.
+
+Uni-directional NAT44ed throughput tests are using TRex STL (Stateless)
+APIs and traffic profiles, but with packets sent only in
+inside-to-outside direction. Due to indeterministic bindings of outside
+to inside (src_addr,src_port) that are created dynamically at flow start
+bidirectional testing is not possible with stateless traffic profiles.
+See :ref:`data_plane_throughput` for more detail.
+
+Similarly to NAT44det, NAT44ed uni-directional throughput tests include
+a ramp-up phase to establish and verify the presence of required NAT44ed
+binding entries. NAT44ed CPS (connections-per-second) and throughput /
+PPS stateful tests do not have a ramp-up phase.
+
+Stateful NAT44ed tests are using TRex ASTF (Advanced Stateful) APIs and
+traffic profiles, with packets sent in both directions. Tests are run
+with both UDP and TCP/IP sessions.
+
+Associated CSIT test cases use the following naming scheme to indicate
+NAT44DET case tested:
+
+- Stateless: ethip4udp-nat44ed-h{H}-p{P}-s{S}-udir-[mrr|ndrpdr|soak]
+
+ - {H}, number of inside hosts, H = 1024, 4096, 16384, 65536, 262144.
+ - {P}, number of ports per inside host, P = 63.
+ - {S}, number of sessions, S = 64512, 258048, 1032192, 4128768,
+ 16515072.
+ - udir-[mrr|ndrpdr|soak], unidirectional stateless tests MRR, NDRPDR
+ or SOAK.
+
+- Stateful: ethip4[udp|tcp]-nat44ed-h{H}-p{P}-s{S}-[cps|pps]-[mrr|ndrpdr]
+
+ - [udp|tcp], UDP or TCP/IP sessions
+ - {H}, number of inside hosts, H = 1024, 4096, 16384, 65536, 262144.
+ - {P}, number of ports per inside host, P = 63.
+ - {S}, number of sessions, S = 64512, 258048, 1032192, 4128768,
+ 16515072.
+ - [cps|pps], connections-per-second session establishment rate or
+ packets-per-second throughput rate.
+ - [mrr|ndrpdr], bidirectional stateful tests MRR, NDRPDR.