diff options
Diffstat (limited to 'tests/dpdk/perf/10ge2p1x520-eth-l2xcbase-testpmd-ndrpdrdisc.robot')
-rw-r--r-- | tests/dpdk/perf/10ge2p1x520-eth-l2xcbase-testpmd-ndrpdrdisc.robot | 410 |
1 files changed, 0 insertions, 410 deletions
diff --git a/tests/dpdk/perf/10ge2p1x520-eth-l2xcbase-testpmd-ndrpdrdisc.robot b/tests/dpdk/perf/10ge2p1x520-eth-l2xcbase-testpmd-ndrpdrdisc.robot deleted file mode 100644 index 82365737c7..0000000000 --- a/tests/dpdk/perf/10ge2p1x520-eth-l2xcbase-testpmd-ndrpdrdisc.robot +++ /dev/null @@ -1,410 +0,0 @@ -# Copyright (c) 2018 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance/performance_setup.robot -| Resource | resources/libraries/robot/dpdk/default.robot -| Library | resources.libraries.python.topology.Topology -| Library | resources.libraries.python.NodePath -| Library | resources.libraries.python.InterfaceUtil -| Library | resources.libraries.python.DPDK.DPDKTools -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | HW_ENV | PERFTEST | NDRPDRDISC | 1NUMA -| ... | NIC_Intel-X520-DA2 | DPDK | ETH | L2XCFWD | BASE -| Suite Setup | Set up DPDK 3-node performance topology with DUT's NIC model -| ... | L2 | Intel-X520-DA2 -| Suite Teardown | Tear down DPDK 3-node performance topology -| Documentation | *RFC2544: Pkt throughput IPv4 routing test cases* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ -| ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 frame forwarding. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 run the DPDK testpmd\ -| ... | application and use the io forwarding mode. DUT1 and DUT2 tested with\ -| ... | 2p10GE NIC X520 Niantic by Intel. -| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ -| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ -| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ -| ... | of packets transmitted. NDR and PDR are discovered for different\ -| ... | Ethernet L2 frame sizes using either binary search or linear search\ -| ... | algorithms with configured starting rate and final step that determines\ -| ... | throughput measurement resolution. Test packets are generated by TG on\ -| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\ -| ... | (flow-group per direction, 253 flows per flow-group) with all packets\ -| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\ -| ... | payload. MAC addresses are matching MAC addresses of the TG node\ -| ... | interfaces. -| ... | *[Ref] Applicable standard specifications:* RFC2544. - -*** Variables *** -# X520-DA2 bandwidth limit -| ${s_limit} | ${10000000000} -# Traffic profile: -| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 - -*** Test Cases *** -| tc01-64B-1t1c-eth-l2xcbase-testpmd-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 phy core,\ -| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames\ -| | ... | using binary search start at 10GE linerate, step 100kpps. -| | ... -| | [Tags] | 64B | 1C | NDRDISC -| | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 1 | 1 | no -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc02-64B-1t1c-eth-l2xcbase-testpmd-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 phy core,\ -| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames\ -| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. -| | ... -| | [Tags] | 64B | 1C | PDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 1 | 1 | no -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} - -| tc03-1518B-1t1c-eth-l2xcbase-testpmd-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 phy core,\ -| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames\ -| | ... | using binary search start at 10GE linerate, step 10kpps. -| | ... -| | [Tags] | 1518B | 1C | NDRDISC -| | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 1 | 1 | no -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc04-1518B-1t1c-eth-l2xcbase-testpmd-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 phy core,\ -| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames\ -| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. -| | ... -| | [Tags] | 1518B | 1C | PDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 1 | 1 | no -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} - -| tc05-9000B-1t1c-eth-l2xcbase-testpmd-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 phy core,\ -| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames\ -| | ... | using binary search start at 10GE linerate, step 10kpps. -| | ... -| | [Tags] | 9000B | 1C | NDRDISC -| | ... -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 1 | 1 | yes -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc06-9000B-1t1c-eth-l2xcbase-testpmd-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 1 phy core,\ -| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames\ -| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. -| | ... -| | [Tags] | 9000B | 1C | PDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 1 | 1 | yes -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} - -| tc07-64B-2t2c-eth-l2xcbase-testpmd-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 phy\ -| | ... | cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte\ -| | ... | frames using binary search start at 10GE linerate, step 100kpps. -| | ... -| | [Tags] | 64B | 2C | NDRDISC -| | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 2 | 1 | no -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc08-64B-2t2c-eth-l2xcbase-testpmd-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 phy\ -| | ... | cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte\ -| | ... | frames using binary search start at 10GE linerate, step 100kpps,\ -| | ... | LT=0.5%. -| | ... -| | [Tags] | 64B | 2C | PDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 2 | 1 | no -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} - -| tc09-1518B-2t2c-eth-l2xcbase-testpmd-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 phy\ -| | ... | cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte\ -| | ... | frames using binary search start at 10GE linerate, step 10kpps. -| | ... -| | [Tags] | 1518B | 2C | NDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 2 | 1 | no -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc10-1518B-2t2c-eth-l2xcbase-testpmd-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 phy\ -| | ... | cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte\ -| | ... | frames using binary search start at 10GE linerate, step 10kpps,\ -| | ... | LT=0.5%. -| | ... -| | [Tags] | 1518B | 2C | PDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 2 | 1 | no -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} - -| tc11-9000B-2t2c-eth-l2xcbase-testpmd-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 phy\ -| | ... | cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte\ -| | ... | frames using binary search start at 10GE linerate, step 10kpps. -| | ... -| | [Tags] | 9000B | 2C | NDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 2 | 1 | yes -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc12-9000B-2t2c-eth-l2xcbase-testpmd-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 2 phy\ -| | ... | cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte\ -| | ... | frames using binary search start at 10GE linerate, step 10kpps,\ -| | ... | LT=0.5%. -| | ... -| | [Tags] | 9000B | 2C | PDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 2 | 1 | yes -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} - -| tc13-64B-4t4c-eth-l2xcbase-testpmd-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 phy\ -| | ... | cores, 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte\ -| | ... | frames using binary search start at 10GE linerate, step 100kpps. -| | ... -| | [Tags] | 64B | 4C | NDRDISC -| | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 4 | 2 | no -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc14-64B-4t4c-eth-l2xcbase-testpmd-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 phy\ -| | ... | cores, 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte\ -| | ... | frames using binary search start at 10GE linerate, step 100kpps,\ -| | ... | LT=0.5%. -| | ... -| | [Tags] | 64B | 4C | PDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 4 | 2 | no -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} - -| tc15-1518B-4t4c-eth-l2xcbase-testpmd-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 phy\ -| | ... | cores, 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte\ -| | ... | frames using binary search start at 10GE linerate, step 10kpps. -| | ... -| | [Tags] | 1518B | 4C | NDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 4 | 2 | no -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc16-1518B-4t4c-eth-l2xcbase-testpmd-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 phy\ -| | ... | cores, 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte\ -| | ... | frames using binary search start at 10GE linerate, step 10kpps,\ -| | ... | LT=0.5%. -| | ... -| | [Tags] | 1518B | 4C | PDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 4 | 2 | no -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} - -| tc17-9000B-4t4c-eth-l2xcbase-testpmd-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 phy\ -| | ... | cores, 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte\ -| | ... | frames using binary search start at 10GE linerate, step 10kpps. -| | ... -| | [Tags] | 9000B | 4C | NDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 4 | 2 | yes -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc18-9000B-4t4c-eth-l2xcbase-testpmd-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2 frame forwarding config with 4 phy\ -| | ... | cores, 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte -| | ... | frames using binary search start at 10GE linerate, step 5kpps,\ -| | ... | LT=0.5%. -| | ... -| | [Tags] | 9000B | 4C | PDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Start L2FWD on all DUTs | 4 | 2 | yes -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} |