1 files changed, 116 insertions, 0 deletions
diff --git a/tests/func/honeycomb/010_interface_management.robot b/tests/func/honeycomb/010_interface_management.robot
new file mode 100644
index 0000000000..e9798167c7
--- /dev/null
+++ b/tests/func/honeycomb/010_interface_management.robot
@@ -0,0 +1,116 @@
+# Copyright (c) 2016 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Variables ***
+# Interface to run tests on.
+| ${interface}= | ${node['interfaces']['port1']['name']}
+# Configuration which will be set and verified during tests.
+| ${ipv4_address}= | 192.168.0.2
+| ${ipv4_address2}= | 192.168.0.3
+| ${ipv4_mask}= | 255.255.255.0
+| ${ipv4_prefix}= | ${24}
+| @{ipv4_neighbor}= | 192.168.0.4 | 08:00:27:c0:5d:37
+| &{ipv4_settings}= | enabled=${True} | forwarding=${True} | mtu=${9000}
+| @{ipv6_address}= | 10::10 | ${64}
+| @{ipv6_neighbor}= | 10::11 | 08:00:27:c0:5d:37
+| &{ipv6_settings}= | enabled=${True} | forwarding=${True} | mtu=${9000}
+| ... | dup-addr-detect-transmits=${5}
+| &{ethernet}= | mtu=${9000}
+| &{routing}= | vrf-id=${27}
+| &{vxlan_settings}= | src=10.0.1.20 | dst=10.0.3.20 | vni=${1000}
+| ... | encap-vrf-id=${1000}
+
+*** Settings ***
+| Resource | resources/libraries/robot/default.robot
+| Resource | resources/libraries/robot/honeycomb/interfaces.robot
+| Force Tags | honeycomb_sanity
+| Documentation | *Honeycomb interface management test suite.*
+| ...
+| ... | Test suite uses the first interface of the first DUT node.
+
+*** Test Cases ***
+| Honeycomb configures and reads interface state
+| | [Documentation] | Check if Honeycomb API can modify the admin state of\
+| | ... | VPP interfaces.
+| | Given Interface state is | ${node} | ${interface} | down
+| | When Honeycomb sets interface state | ${node} | ${interface} | up
+| | Then Interface state from Honeycomb should be
+| | ... | ${node} | ${interface} | up
+| | And Interface state from VAT should be | ${node} | ${interface} | up
+| | When Honeycomb sets interface state | ${node} | ${interface} | down
+| | Then Interface state from Honeycomb should be
+| | ... | ${node} | ${interface} | down
+| | And Interface state from VAT should be | ${node} | ${interface} | down
+
+| Honeycomb modifies interface configuration - ipv4 (netmask)
+| | [Documentation] | Check if Honeycomb API can configure interfaces for ipv4\
+| | ... | with address and netmask provided.
+| | When Honeycomb sets interface ipv4 address | ${node} | ${interface}
+| | ... | ${ipv4_address} | ${ipv4_mask} | ${ipv4_settings}
+| | And Honeycomb adds interface ipv4 neighbor
+| | ... | ${node} | ${interface} | @{ipv4_neighbor}
+| | Then IPv4 config from Honeycomb should be
+| | ... | ${node} | ${interface} | ${ipv4_address} | ${ipv4_prefix}
+| | ... | @{ipv4_neighbor} | ${ipv4_settings}
+| | And IPv4 config from VAT should be
+| | ... | ${node} | ${interface} | ${ipv4_address} | ${ipv4_prefix}
+
+| Honeycomb removes ipv4 address from interface
+| | [Documentation] | Check if Honeycomb API can remove configured ipv4\
+| | ... | addresses from interface.
+| | Given IPv4 config from Honeycomb should be
+| | ... | ${node} | ${interface} | ${ipv4_address} | ${ipv4_prefix}
+| | ... | @{ipv4_neighbor} | ${ipv4_settings}
+| | And IPv4 config from VAT should be
+| | ... | ${node} | ${interface} | ${ipv4_address} | ${ipv4_prefix}
+| | When Honeycomb removes interface ipv4 addresses | ${node} | ${interface}
+| | Then IPv4 address from Honeycomb should be empty | ${node} |${interface}
+| | And ipv4 address from VAT should be empty | ${node} | ${interface}
+
+| Honeycomb modifies interface configuration - ipv4 (prefix)
+| | [Documentation] | Check if Honeycomb API can configure interfaces for ipv4\
+| | ... | with address and prefix provided.
+| | [Teardown] | Honeycomb removes interface ipv4 addresses | ${node}
+| | ... | ${interface}
+| | When Honeycomb sets interface ipv4 address with prefix
+| | ... | ${node} | ${interface} | ${ipv4_address2} | ${ipv4_prefix}
+| | ... | ${ipv4_settings}
+| | And Honeycomb adds interface ipv4 neighbor
+| | ... | ${node} | ${interface} | @{ipv4_neighbor}
+| | Then IPv4 config from Honeycomb should be
+| | ... | ${node} | ${interface} | ${ipv4_address2} | ${ipv4_prefix}
+| | ... | @{ipv4_neighbor}
+| | ... | ${ipv4_settings}
+| | And IPv4 config from VAT should be
+| | ... | ${node} | ${interface} | ${ipv4_address2} | ${ipv4_prefix}
+
+| Honeycomb modifies interface configuration - ipv6
+| | [Documentation] | Check if Honeycomb API can configure interfaces for ipv6.
+| | When Honeycomb sets interface ipv6 configuration
+| | ... | ${node} | ${interface} | @{ipv6_address} | @{ipv6_neighbor}
+| | ... | ${ipv6_settings}
+| | Then IPv6 config from Honeycomb should be
+| | ... | ${node} | ${interface} | @{ipv6_address} | @{ipv6_neighbor}
+| | ... | ${ipv6_settings}
+| | And IPv6 config from VAT should be
+| | ... | ${node} | ${interface} | @{ipv6_address}
+
+| Honeycomb modifies interface configuration - ethernet,routing
+| | [Documentation] | Check if Honeycomb API can configure interface ethernet\
+| | ... | and routing settings.
+| | When Honeycomb sets interface ethernet and routing configuration
+| | ... | ${node} | ${interface} | ${ethernet} | ${routing}
+| | Then Interface ethernet and routing configuration from Honeycomb should be
+| | ... | ${node} | ${interface} | ${ethernet} | ${routing}
+| | And Interface ethernet and routing configuration from VAT should be
+| | ... | ${node} | ${interface} | ${ethernet['mtu']} | ${routing['vrf-id']}