diff options
Diffstat (limited to 'tests/func/lisp/eth2p-ethip4lispgpe-ip6basevrf-func.robot')
| -rw-r--r-- | tests/func/lisp/eth2p-ethip4lispgpe-ip6basevrf-func.robot | 113 |
1 files changed, 113 insertions, 0 deletions
diff --git a/tests/func/lisp/eth2p-ethip4lispgpe-ip6basevrf-func.robot b/tests/func/lisp/eth2p-ethip4lispgpe-ip6basevrf-func.robot new file mode 100644 index 0000000000..41d5dcf8cb --- /dev/null +++ b/tests/func/lisp/eth2p-ethip4lispgpe-ip6basevrf-func.robot @@ -0,0 +1,113 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/default.robot +| Resource | resources/libraries/robot/testing_path.robot +| Resource | resources/libraries/robot/ipv4.robot +| Resource | resources/libraries/robot/traffic.robot +| Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot +| Resource | resources/libraries/robot/l2_traffic.robot +| Resource | resources/libraries/robot/lisp/lispgpe.robot +| Resource | resources/libraries/robot/bridge_domain.robot +| Resource | resources/libraries/robot/qemu.robot +| Library | resources.libraries.python.IPUtil +| Library | resources.libraries.python.VhostUser +| Library | resources.libraries.python.Trace +| Library | resources.libraries.python.VPPUtil +# import additional Lisp settings from resource file +| Variables | resources/test_data/lisp/static_adjacency/lisp_static_adjacency.py +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | 3_NODE_DOUBLE_LINK_TOPO +| ... | VM_ENV | HW_ENV +| Test Setup | Func Test Setup +| Test Teardown | Func Test Teardown +| Documentation | *LISP static adjacency test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2,\ +| ... | Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv4 tunnel. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6\ +| ... | routing and static routes. LISPoIPv4 tunnel is configured\ +| ... | between DUT1 and DUT2. +| ... | *[Ver] TG verification:* Test ICMPv6 Echo Request packets\ +| ... | are sent in both directions by TG on links to DUT1 and DUT2; on receive\ +| ... | TG verifies packets for correctness and their IPv6 src-addr,\ +| ... | dst-addr and MAC addresses. +| ... | *[Ref] Applicable standard specifications:* RFC6830. + +*** Test Cases *** +| TC01: DUT1 and DUT2 route IPv6 bidirectionally over LISP GPE tunnel using physical interfaces and VRF is enabled +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. +| | ... | [Enc] Eth-IPv4-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on\ +| | ... | TG-DUTn. +| | ... | [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2. +| | ... | [Ver] Case: ip6-lispgpe-ip4 - vrf, phy2lisp +| | ... | Make TG send ICMPv4 Echo Req between its interfaces across both\ +| | ... | DUTs and LISP GPE tunnel between them; verify IPv6 headers on\ +| | ... | received packets are correct. +| | ... | [Ref] RFC6830. +| | ... +| | [Teardown] | Run Keywords | Show Packet Trace on All DUTs | ${nodes} +| | ... | AND | Show vpp trace dump on all DUTs +| | ... | AND | Show Vpp Settings | ${nodes['DUT1']} +| | ... | AND | Show Vpp Settings | ${nodes['DUT2']} +| | ... | AND | Check VPP PID in Teardown +| | ... +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | And Assign Interface To Fib Table | ${dut1_node} +| | ... | ${dut1_to_tg} | ${fib_table_1} | ip6=${TRUE} +| | And Assign Interface To Fib Table | ${dut2_node} +| | ... | ${dut2_to_tg} | ${fib_table_1} | ip6=${TRUE} +| | And Add IP Neighbors | ${fib_table_1} +| | And IP addresses are set on interfaces +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${dut1_to_dut2_ip6o4} +| | ... | ${dut_prefix6o4} +| | ... | ${dut1_node} | ${dut1_to_tg} | ${dut1_to_tg_ip6o4} | ${tg_prefix6o4} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut_prefix6o4} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} +| | When Set up LISP GPE topology +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${NONE} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} +| | ... | ${dut2_ip6o4_static_adjacency} +| | ... | ${dut1_dut2_vni} | ${fib_table_1} +| | Then Send Packet And Check Headers +| | ... | ${tg_node} | ${tg1_ip6o4} | ${tg2_ip6o4} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Send Packet And Check Headers +| | ... | ${tg_node} | ${tg2_ip6o4} | ${tg1_ip6o4} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} + +*** Keywords *** +| Add IP Neighbors +| | [Documentation] +| | ... | Add IP neighbors to physical interfaces on DUTs.\ +| | ... | You can specify fib table ID for DUT-TG interfaces. Default is 0. +| | ... +| | [Arguments] | ${fib_id}=0 +| | Add IP Neighbor | ${dut1_node} | ${dut1_to_tg} | ${tg1_ip6o4} +| | ... | ${tg_to_dut1_mac} | ${fib_id} +| | Add IP Neighbor | ${dut2_node} | ${dut2_to_tg} | ${tg2_ip6o4} +| | ... | ${tg_to_dut2_mac} | ${fib_id} +| | Add IP Neighbor | ${dut1_node} | ${dut1_to_dut2} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_dut1_mac} +| | Add IP Neighbor | ${dut2_node} | ${dut2_to_dut1} | ${dut1_to_dut2_ip6o4} +| | ... | ${dut1_to_dut2_mac} |