diff options
Diffstat (limited to 'tests/func/lisp')
| -rw-r--r-- | tests/func/lisp/lisp_api_untagged.robot | 119 | ||||
| -rw-r--r-- | tests/func/lisp/lisp_dataplane_untagged.robot | 277 |
2 files changed, 396 insertions, 0 deletions
diff --git a/tests/func/lisp/lisp_api_untagged.robot b/tests/func/lisp/lisp_api_untagged.robot new file mode 100644 index 0000000000..f92a92d435 --- /dev/null +++ b/tests/func/lisp/lisp_api_untagged.robot @@ -0,0 +1,119 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Library | resources.libraries.python.topology.Topology +| Library | resources.libraries.python.NodePath +| Library | resources.libraries.python.Trace +| Library | resources.libraries.python.LispUtil +| Resource | resources/libraries/robot/default.robot +| Resource | resources/libraries/robot/interfaces.robot +| Resource | resources/libraries/robot/lisp/lisp_api.robot +# import additional Lisp settings from resource file +| Variables | resources/test_data/lisp/api/lisp_api_resources.py +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | 3_NODE_DOUBLE_LINK_TOPO +| ... | VM_ENV | HW_ENV +| Test Setup | Run Keywords | Setup all DUTs before test +| ... | AND | Setup all TGs before traffic script +| ... | AND | Update All Interface Data On All Nodes | ${nodes} +| Test Teardown | Run Keywords | Show Packet Trace on All DUTs | ${nodes} +| ... | AND | Show vpp trace dump on all DUTs +| Documentation | *LISP API test cases* +| ... +| ... | *[Top] Network Topologies:* DUT1 1-node topology. +| ... | *[Enc] Packet Encapsulations:* None. +| ... | *[Cfg] DUT configuration:* DUT1 gets configured with all LISP +| ... | parameters. +| ... | *[Ver] Verification:* DUT1 operational data gets verified following +| ... | configuration. +| ... | *[Ref] Applicable standard specifications:* RFC6830. + +*** Variables *** +| ${locator_set_num}= | 3 + +*** Test Cases *** + +| TC01: DUT can enable and disable LISP +| | [Documentation] +| | ... | [Top] DUT1. [Enc] None. [Cfg1] Test LISP enable/disable API; On \ +| | ... | DUT1 enable LISP. [Ver1] Check DUT1 if LISP is enabled. [Cfg2] +| | ... | Then disable LISP. [Ver2] Check DUT1 if LISP is disabled. [Ref] +| | ... | RFC6830. +| | [Tags] | EXPECTED_FAILING +| | When Enable lisp | ${nodes['DUT1']} +| | Then Check if lisp is enabled | ${nodes['DUT1']} | ${lisp_status} +| | When Disable lisp | ${nodes['DUT1']} +| | Then Check if lisp is disabled | ${nodes['DUT1']} | ${lisp_status} + +| TC02: DUT can add and delete locator_set +| | [Documentation] +| | ... | [Top] DUT1. [Enc] None. [Cfg1] Test LISP locator_set API; on \ +| | ... | DUT1 configure locator_set and locator. [Ver1] Check DUT1 +| | ... | configured locator_set and locator are correct. [Cfg2] Then +| | ... | remove locator_set and locator. [Ver2] check DUT1 locator_set +| | ... | and locator are removed. [Ref] RFC6830. +| | [Tags] | EXPECTED_FAILING +| | Given Lisp locator_set data is prepared +| | ... | ${nodes['DUT1']} | ${locator_set_num} +| | And Enable lisp | ${nodes['DUT1']} +| | When Lisp locator_set data is set | ${nodes['DUT1']} +| | Then Lisp locator_set is set correctly | ${nodes['DUT1']} +| | When Delete all lisp locator_set from VPP | ${nodes['DUT1']} +| | Then Lisp locator_set should be unset | ${nodes['DUT1']} + +| TC03: DUT can add, reset and delete locator_set +| | [Documentation] +| | ... | [Top] DUT1. [Enc] None. [Cfg1] Test LISP locator_set API; on \ +| | ... | DUT1 configure locator_set and locator. [Ver1] Check DUT1 +| | ... | locator_set and locator are correct. [Cfg2] Then reset +| | ... | locator_set and set it again. [Ver2] Check DUT1 locator_set and +| | ... | locator are correct. [Cfg3] Then remove locator_set and locator. +| | ... | [Ver3] Check DUT1 all locator_set and locators are removed. +| | ... | [Ref] RFC6830. +| | [Tags] | EXPECTED_FAILING +| | Given Lisp locator_set data use for test reset locator_set are prepared +| | ... | ${nodes['DUT1']} | ${locator_set_num} +| | And Enable lisp | ${nodes['DUT1']} +| | When Lisp locator_set data is set | ${nodes['DUT1']} +| | Then Lisp locator_set is set correctly | ${nodes['DUT1']} +| | When Delete all lisp locator_set from VPP | ${nodes['DUT1']} +| | Then Lisp locator_set should be unset | ${nodes['DUT1']} + +| TC04: DUT can add and delete eid address +| | [Documentation] +| | ... | [Top] DUT1. [Enc] None. [Cfg1] Test LISP eid API; on DUT1 \ +| | ... | configure LISP eid IP address. [Ver1] Check DUT1 configured data +| | ... | is correct. [Cfg2] Remove configured data. [Ver2] Check DUT1 all +| | ... | eid IP addresses are removed. [Ref] RFC6830. +| | [Tags] | EXPECTED_FAILING +| | Given Enable lisp | ${nodes['DUT1']} +| | When Lisp eid address is set | ${nodes['DUT1']} | ${eid_table} +| | Then Lisp eid address is set correctly to eid table | ${nodes['DUT1']} +| | ... | ${eid_table} +| | When Delete all lisp eid address from VPP | ${nodes['DUT1']} | ${eid_table} +| | Then Lisp eid table should be empty | ${nodes['DUT1']} + +| TC05: DUT can add and delete LISP map resolver address +| | [Documentation] +| | ... | [Top] DUT1. [Enc] None. [Cfg1] Test LISP map resolver address \ +| | ... | API; on DUT1 configure LISP map resolver address. [Ver1] Check +| | ... | DUT1 configured data is correct. [Cfg2] Remove configured data. +| | ... | [Ver2] Check DUT1 all map resolver addresses are removed. [Ref] +| | ... | RFC6830. +| | Given Enable lisp | ${nodes['DUT1']} +| | When Lisp map resolver address is set | ${nodes['DUT1']} | ${map_resolver} +| | Then Lisp map resolver address is set correctly | ${nodes['DUT1']} +| | ... | ${map_resolver} +| | When Delete all lisp map resolver address from VPP | ${nodes['DUT1']} +| | ... | ${map_resolver} +| | Then Lip map resolver address should be empty | ${nodes['DUT1']} diff --git a/tests/func/lisp/lisp_dataplane_untagged.robot b/tests/func/lisp/lisp_dataplane_untagged.robot new file mode 100644 index 0000000000..0808d366c6 --- /dev/null +++ b/tests/func/lisp/lisp_dataplane_untagged.robot @@ -0,0 +1,277 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/default.robot +| Resource | resources/libraries/robot/testing_path.robot +| Resource | resources/libraries/robot/ipv4.robot +| Resource | resources/libraries/robot/traffic.robot +| Resource | resources/libraries/robot/lisp/lisp_static_mapping.robot +| Resource | resources/libraries/robot/l2_traffic.robot +| Library | resources.libraries.python.IPUtil +| Library | resources.libraries.python.Trace +| Library | resources.libraries.python.IPv4Util.IPv4Util +# import additional Lisp settings from resource file +| Variables | resources/test_data/lisp/static_mapping/lisp_static_mapping.py +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | 3_NODE_DOUBLE_LINK_TOPO +| ... | VM_ENV | HW_ENV +| Test Setup | Run Keywords | Setup all DUTs before test +| ... | AND | Setup all TGs before traffic script +| ... | AND | Update All Interface Data On All Nodes | ${nodes} +| Test Teardown | Run Keywords | Show Packet Trace on All DUTs | ${nodes} +| ... | AND | Show vpp trace dump on all DUTs +| Documentation | *LISP static remote mapping test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, +| ... | Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel; +| ... | Eth-IPv6-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for +| ... | IPv6 routing over LISPoIPv6 tunnel; Eth-IPv6-LISP-IPv4-ICMPv4 on +| ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv6 +| ... | tunnel; Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on +| ... | TG-DUTn for IPv6 routing over LISPoIPv4 tunnel. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4 (IPv6) +| ... | routing and static routes. LISPoIPv4 (oIPv6) tunnel is configured +| ... | between DUT1 and DUT2. +| ... | *[Ver] TG verification:* Test ICMPv4 (or ICMPv6) Echo Request packets +| ... | are sent in both directions by TG on links to DUT1 and DUT2; on receive +| ... | TG verifies packets for correctness and their IPv4 (IPv6) src-addr, +| ... | dst-addr and MAC addresses. +| ... | *[Ref] Applicable standard specifications:* RFC6830. + +*** Test Cases *** +| TC01: DUT1 and DUT2 route IPv4 bidirectionally over LISPoIPv4 tunnel +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISP-IPv4-ICMPv4 on \ +| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 and DUT2 +| | ... | configure IPv4 LISP remote static mappings. [Ver] Make TG send +| | ... | ICMPv4 Echo Req between its interfaces across both DUTs and LISP +| | ... | tunnel between them; verify IPv4 headers on received packets are +| | ... | correct. [Ref] RFC6830. +| | [Tags] | EXPECTED_FAILING +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | And IP addresses are set on interfaces +| | ... | ${dut1_node} | ${dut1_to_dut2} +| | ... | ${dut1_to_dut2_ip4} | ${prefix4} +| | ... | ${dut1_node} | ${dut1_to_tg} +| | ... | ${dut1_to_tg_ip4} | ${prefix4} +| | ... | ${dut2_node} | ${dut2_to_dut1} +| | ... | ${dut2_to_dut1_ip4} | ${prefix4} +| | ... | ${dut2_node} | ${dut2_to_tg} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And VPP IP Probe | ${dut1_node} | ${dut1_to_dut2} | ${dut2_to_dut1_ip4} +| | And VPP IP Probe | ${dut2_node} | ${dut2_to_dut1} | ${dut1_to_dut2_ip4} +| | And Add Arp On Dut | ${dut2_node} | ${dut2_to_tg} | ${tg2_ip4} +| | ... | ${tg_to_dut2_mac} +| | And Add Arp On Dut | ${dut1_node} | ${dut1_to_tg} | ${tg1_ip4} +| | ... | ${tg_to_dut1_mac} +| | When Set up Lisp topology +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${NONE} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_mapping} | ${dut2_ip4_static_mapping} +| | Then Send Packet And Check Headers +| | ... | ${tg_node} | ${tg1_ip4} | ${tg2_ip4} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Send Packet And Check Headers +| | ... | ${tg_node} | ${tg2_ip4} | ${tg1_ip4} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} + +| TC02: DUT1 and DUT2 route IPv6 bidirectionally over LISPoIPv6 tunnel +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-LISP-IPv6-ICMPv6 on \ +| | ... | DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] On DUT1 and DUT2 +| | ... | configure IPv6 LISP remote static mappings. [Ver] Make TG send +| | ... | ICMPv6 Echo Req between its interfaces across both DUTs and LISP +| | ... | tunnel between them; verify IPv4 headers on received packets are +| | ... | correct. [Ref] RFC6830. +| | [Tags] | EXPECTED_FAILING +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | And IP addresses are set on interfaces +| | ... | ${dut1_node} | ${dut1_to_dut2} +| | ... | ${dut1_to_dut2_ip6} | ${prefix6} +| | ... | ${dut1_node} | ${dut1_to_tg} +| | ... | ${dut1_to_tg_ip6} | ${prefix6} +| | ... | ${dut2_node} | ${dut2_to_dut1} +| | ... | ${dut2_to_dut1_ip6} | ${prefix6} +| | ... | ${dut2_node} | ${dut2_to_tg} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And VPP IP Probe | ${dut1_node} | ${dut1_to_dut2} | ${dut2_to_dut1_ip6} +| | And VPP IP Probe | ${dut2_node} | ${dut2_to_dut1} | ${dut1_to_dut2_ip6} +| | And Add Arp On Dut | ${dut2_node} | ${dut2_to_tg} | ${tg2_ip6} +| | ... | ${tg_to_dut2_mac} +| | And Add Arp On Dut | ${dut1_node} | ${dut1_to_tg} | ${tg1_ip6} +| | ... | ${tg_to_dut1_mac} +| | When Set up Lisp topology +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${NONE} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_mapping} | ${dut2_ip6_static_mapping} +| | Then Send Packet And Check Headers +| | ... | ${tg_node} | ${tg1_ip6} | ${tg2_ip6} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Send Packet And Check Headers +| | ... | ${tg_node} | ${tg2_ip6} | ${tg1_ip6} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} + +| TC03: DUT1 and DUT2 route IPv4 bidirectionally over LISPoIPv6 tunnel +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-LISP-IPv4-ICMPv4 on \ +| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 and DUT2 +| | ... | configure IPv6 LISP remote static mappings. [Ver] Make TG send +| | ... | ICMPv4 Echo Req between its interfaces across both DUTs and LISP +| | ... | tunnel between them; verify IPv4 headers on received packets are +| | ... | correct. [Ref] RFC6830. +| | [Tags] | EXPECTED_FAILING +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | And IP addresses are set on interfaces +| | ... | ${dut1_node} | ${dut1_to_dut2} +| | ... | ${dut1_to_dut2_ip4o6} | ${dut_prefix4o6} +| | ... | ${dut1_node} | ${dut1_to_tg} +| | ... | ${dut1_to_tg_ip4o6} | ${tg_prefix4o6} +| | ... | ${dut2_node} | ${dut2_to_dut1} +| | ... | ${dut2_to_dut1_ip4o6} | ${dut_prefix4o6} +| | ... | ${dut2_node} | ${dut2_to_tg} +| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} +| | And VPP IP Probe | ${dut1_node} | ${dut1_to_dut2} | ${dut2_to_dut1_ip4o6} +| | And VPP IP Probe | ${dut2_node} | ${dut2_to_dut1} | ${dut1_to_dut2_ip4o6} +| | And Add Arp On Dut | ${dut2_node} | ${dut2_to_tg} | ${tg2_ip4o6} +| | ... | ${tg_to_dut2_mac} +| | And Add Arp On Dut | ${dut1_node} | ${dut1_to_tg} | ${tg1_ip4o6} +| | ... | ${tg_to_dut1_mac} +| | When Set up Lisp topology +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${NONE} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} +| | ... | ${dut1_ip4o6_static_mapping} | ${dut2_ip4o6_static_mapping} +| | Then Send Packet And Check Headers +| | ... | ${tg_node} | ${tg1_ip4o6} | ${tg2_ip4o6} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Send Packet And Check Headers +| | ... | ${tg_node} | ${tg2_ip4o6} | ${tg1_ip4o6} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} + +| TC04: DUT1 and DUT2 route IPv6 bidirectionally over LISPoIPv4 tunnel +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISP-IPv6-ICMPv6 on \ +| | ... | DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] On DUT1 and DUT2 +| | ... | configure IPv4 LISP remote static mappings. [Ver] Make TG send +| | ... | ICMPv6 Echo Req between its interfaces across both DUTs and LISP +| | ... | tunnel between them; verify IPv4 headers on received packets are +| | ... | correct. [Ref] RFC6830. +| | [Tags] | EXPECTED_FAILING +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | And IP addresses are set on interfaces +| | ... | ${dut1_node} | ${dut1_to_dut2} +| | ... | ${dut1_to_dut2_ip6o4} | ${dut_prefix6o4} +| | ... | ${dut1_node} | ${dut1_to_tg} +| | ... | ${dut1_to_tg_ip6o4} | ${tg_prefix6o4} +| | ... | ${dut2_node} | ${dut2_to_dut1} +| | ... | ${dut2_to_dut1_ip6o4} | ${dut_prefix6o4} +| | ... | ${dut2_node} | ${dut2_to_tg} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} +| | And VPP IP Probe | ${dut1_node} | ${dut1_to_dut2} | ${dut2_to_dut1_ip6o4} +| | And VPP IP Probe | ${dut2_node} | ${dut2_to_dut1} | ${dut1_to_dut2_ip6o4} +| | And Add Arp On Dut | ${dut2_node} | ${dut2_to_tg} | ${tg2_ip6o4} +| | ... | ${tg_to_dut2_mac} +| | And Add Arp On Dut | ${dut1_node} | ${dut1_to_tg} | ${tg1_ip6o4} +| | ... | ${tg_to_dut1_mac} +| | When Set up Lisp topology +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${NONE} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_mapping} | ${dut2_ip6o4_static_mapping} +| | Then Send Packet And Check Headers +| | ... | ${tg_node} | ${tg1_ip6o4} | ${tg2_ip6o4} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Send Packet And Check Headers +| | ... | ${tg_node} | ${tg2_ip6o4} | ${tg1_ip6o4} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} + +| TC05: DUT1 and DUT2 route IPv4 over LISPoIPv4 tunnel after disable-enable +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISP-IPv4-ICMPv4 on \ +| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg1] On DUT1 and DUT2 +| | ... | configure IPv4 LISP remote static mappings. [Ver1] Make TG send +| | ... | ICMPv4 Echo Req between its interfaces across both DUTs and LISP +| | ... | tunnel between them; verify IPv4 headers on received packets are +| | ... | correct. [Cfg2] Disable LISP. [Ver2] verify packets are not +| | ... | received via LISP tunnel. [Cfg3] Re-enable LISP. [Ver3] verify +| | ... | packets are received again via LISP tunnel. [Ref] RFC6830. +| | [Tags] | EXPECTED_FAILING +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | And IP addresses are set on interfaces +| | ... | ${dut1_node} | ${dut1_to_dut2} +| | ... | ${dut1_to_dut2_ip4} | ${prefix4} +| | ... | ${dut1_node} | ${dut1_to_tg} +| | ... | ${dut1_to_tg_ip4} | ${prefix4} +| | ... | ${dut2_node} | ${dut2_to_dut1} +| | ... | ${dut2_to_dut1_ip4} | ${prefix4} +| | ... | ${dut2_node} | ${dut2_to_tg} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And VPP IP Probe | ${dut1_node} | ${dut1_to_dut2} | ${dut2_to_dut1_ip4} +| | And VPP IP Probe | ${dut2_node} | ${dut2_to_dut1} | ${dut1_to_dut2_ip4} +| | And Add Arp On Dut | ${dut2_node} | ${dut2_to_tg} | ${tg2_ip4} +| | ... | ${tg_to_dut2_mac} +| | And Add Arp On Dut | ${dut1_node} | ${dut1_to_tg} | ${tg1_ip4} +| | ... | ${tg_to_dut1_mac} +| | When Set up Lisp topology +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${NONE} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_mapping} | ${dut2_ip4_static_mapping} +| | Then Send Packet And Check Headers +| | ... | ${tg_node} | ${tg1_ip4} | ${tg2_ip4} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Send Packet And Check Headers +| | ... | ${tg_node} | ${tg2_ip4} | ${tg1_ip4} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} +| | When Disable Lisp | ${dut1_node} +| | Then Send packet from Port to Port should failed +| | ... | ${tg_node} | ${tg1_ip4} | ${tg2_ip4} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Send packet from Port to Port should failed +| | ... | ${tg_node} | ${tg2_ip4} | ${tg1_ip4} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} +| | When Enable Lisp | ${dut1_node} +| | Then Wait Until Keyword Succeeds | 2x | 5s | Send Packet And Check Headers +| | ... | ${tg_node} | ${tg1_ip4} | ${tg2_ip4} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Wait Until Keyword Succeeds | 2x | 5s | Send Packet And Check Headers +| | ... | ${tg_node} | ${tg2_ip4} | ${tg1_ip4} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} |