diff options
Diffstat (limited to 'tests/func/vlan/eth2p-dot1q-l2xcbase-vlantrans11-func.robot')
| -rw-r--r-- | tests/func/vlan/eth2p-dot1q-l2xcbase-vlantrans11-func.robot | 171 |
1 files changed, 0 insertions, 171 deletions
diff --git a/tests/func/vlan/eth2p-dot1q-l2xcbase-vlantrans11-func.robot b/tests/func/vlan/eth2p-dot1q-l2xcbase-vlantrans11-func.robot deleted file mode 100644 index bb91940a32..0000000000 --- a/tests/func/vlan/eth2p-dot1q-l2xcbase-vlantrans11-func.robot +++ /dev/null @@ -1,171 +0,0 @@ -# Copyright (c) 2016 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/default.robot -| Resource | resources/libraries/robot/testing_path.robot -| Resource | resources/libraries/robot/tagging.robot -| Resource | resources/libraries/robot/l2_traffic.robot -| Library | resources.libraries.python.Trace -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | HW_ENV | VM_ENV | SKIP_VPP_PATCH -| Test Setup | Set up functional test -| Test Teardown | Tear down functional test -| Documentation | *L2XC with VLAN tag rewrite test cases - translate-1-1* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet encapsulations:* Eth-dot1q-IPv4-ICMPv4 or -| ... | Eth-dot1q-IPv6-ICMPv6 on TG-DUT1 and DUT1-DUT2, Eth-IPv4-ICMPv4 or -| ... | Eth-IPv4-ICMPv4 on TG-DUT2 for L2 switching of IPv4/IPv6. -| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 cross-connect -| ... | (L2XC) switching between VLAN sub-interface with VLAN tag rewrite -| ... | translate-1-1 method of interface towards TG and interface towards DUT2. -| ... | DUT2 is configured configured with L2 cross-connect (L2XC) switching -| ... | between VLAN sub-interface with VLAN tag rewrite pop-1 method -| ... | of interface towards DUT1 and interface towards TG. -| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets are -| ... | sent from TG on link to DUT1 and received in TG on link form DUT2; -| ... | on receive TG verifies packets for correctness and their IPv4 src-addr, -| ... | dst-addr and MAC addresses. -| ... | *[Ref] Applicable standard specifications:* IEEE 802.1q, IEEE 802.1ad. - -*** Variables *** -| ${subid}= | 10 - -| ${outer_vlan_id1}= | 110 -| ${outer_vlan_id2}= | 120 -| ${outer_vlan_wrong}= | 150 - -| ${src_ip}= | 3ffe:63::1 -| ${dst_ip}= | 3ffe:63::2 - -*** Test Cases *** -| TC01: DUT1 and DUT2 with L2XC and VLAN translate-1-1 (DUT1) switch ICMPv4 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1 and \ -| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 -| | ... | cross-connect (L2XC) with one interface to DUT2 and one VLAN -| | ... | sub-interface towards TG with VLAN tag rewrite translate-1-1 method; -| | ... | on DUT2 configure L2 cross-connect (L2XC) with one interface to TG -| | ... | and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 -| | ... | method. [Ver] Make TG send ICMPv4 Echo Req tagged with one Dot1q tag -| | ... | from one of its interfaces to another one via DUT1 and DUT2; verify -| | ... | that packet is received. [Ref] IEEE 802.1q -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-1 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Send ICMP packet and verify received packet -| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | encaps=Dot1q -| | ... | vlan1=${outer_vlan_id1} - -| TC02: DUT1 and DUT2 with L2XC and VLAN translate-1-1 with wrong tag used (DUT1) switch ICMPv4 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1 and \ -| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 -| | ... | cross-connect (L2XC) with one VLAN tagged sub-interface to DUT2 and -| | ... | one VLAN sub-interface towards TG with VLAN tag rewrite -| | ... | (translate-1-1) on sub-interface to DUT2; on DUT2 configure L2XC with -| | ... | one interface to TG and one VLAN sub-interface towards DUT1 with VLAN -| | ... | tag pop-1. [Ver] Make TG send ICMPv4 Echo Req tagged with one dot1q -| | ... | tag from one of its interfaces to another one via DUT1 and DUT2; -| | ... | verify that packet is not received. [Ref] IEEE 802.1q -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_wrong} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-1 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | encaps=Dot1q | vlan1=${outer_vlan_id1} - -| TC03: DUT1 and DUT2 with L2XC and VLAN translate-1-1 (DUT1) switch ICMPv6 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1 and \ -| | ... | DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 -| | ... | cross-connect (L2XC) with one interface to DUT2 and one VLAN -| | ... | sub-interface towards TG with VLAN tag rewrite translate-1-1 method; -| | ... | on DUT2 configure L2 cross-connect (L2XC) with one interface to TG -| | ... | and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 -| | ... | method. [Ver] Make TG send ICMPv6 Echo Req tagegd with one Dot1q tag -| | ... | from one of its interfaces to another one via DUT1 and DUT2; verify -| | ... | that packet is received. [Ref] IEEE 802.1q -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-1 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Send ICMP packet and verify received packet -| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | src_ip=${src_ip} -| | ... | dst_ip=${dst_ip} | encaps=Dot1q | vlan1=${outer_vlan_id1} - -| TC04: DUT1 and DUT2 with L2XC and VLAN translate-1-1 with wrong tag used (DUT1) switch ICMPv6 between two TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1 and \ -| | ... | DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 -| | ... | cross-connect (L2XC) with one interface to DUT2 and one VLAN -| | ... | sub-interface towards TG with VLAN tag rewrite translate-1-1 method -| | ... | to set tag different from tag set on VLAN sub-interface of DUT2; -| | ... | on DUT2 configure L2 cross-connect (L2XC) with one interface to TG -| | ... | and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 -| | ... | method. [Ver] Make TG send ICMPv6 Echo Req tagegd with one Dot1q tag -| | ... | from one of its interfaces to another one via DUT1 and DUT2; verify -| | ... | that packet is not received. [Ref] IEEE 802.1q -| | [Tags] | SKIP_PATCH -| | Given Configure path in 3-node circular topology -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Set interfaces in 3-node circular topology up -| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface -| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} -| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface -| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} -| | And Configure L2 tag rewrite method on interface | ${dut1_node} -| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_wrong} -| | And Configure L2 tag rewrite method on interface | ${dut2_node} -| | ... | ${vlan2_index} | pop-1 -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} -| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} -| | Then Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} -| | ... | ${tg_to_dut2} | src_ip=${src_ip} | dst_ip=${dst_ip} | encaps=Dot1q -| | ... | vlan1=${outer_vlan_id1} |