diff options
Diffstat (limited to 'tests/func/vxlan/vxlan_bd_untagged.robot')
-rw-r--r-- | tests/func/vxlan/vxlan_bd_untagged.robot | 539 |
1 files changed, 0 insertions, 539 deletions
diff --git a/tests/func/vxlan/vxlan_bd_untagged.robot b/tests/func/vxlan/vxlan_bd_untagged.robot deleted file mode 100644 index b708b6691a..0000000000 --- a/tests/func/vxlan/vxlan_bd_untagged.robot +++ /dev/null @@ -1,539 +0,0 @@ -# Copyright (c) 2016 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/default.robot -| Resource | resources/libraries/robot/testing_path.robot -| Resource | resources/libraries/robot/vxlan.robot -| Resource | resources/libraries/robot/l2_traffic.robot -| Resource | resources/libraries/robot/qemu.robot -| Resource | resources/libraries/robot/double_qemu_setup.robot -| Library | resources.libraries.python.Trace -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | VM_ENV | HW_ENV -| Test Setup | Func Test Setup -| Test Teardown | Func Test Teardown -| Documentation | *RFC7348 VXLAN: Bridge-domain with VXLAN test cases* -| ... -| ... | *[Top] Network topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes; TG=DUT1=DUT2=TG 3-node circular -| ... | topology with double parallel links. -| ... | *[Enc] Packet encapsulations:* Eth-IPv4-VXLAN-Eth-IPv4-ICMPv4 on -| ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for L2 switching of IPv4; -| ... | Eth-IPv6-VXLAN-Eth-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on -| ... | TG-DUTn for L2 switching of IPv6. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 -| ... | bridge-domain (L2BD) switching combined with static MACs, MAC learning -| ... | enabled and Split Horizon Groups (SHG) depending on test case; VXLAN -| ... | tunnels are configured between L2BDs on DUT1 and DUT2. -| ... | *[Ver] TG verification:* Test ICMPv4 (or ICMPv6) Echo Request packets -| ... | are sent in both directions by TG on links to DUT1 and DUT2; on receive -| ... | TG verifies packets for correctness and their IPv4 (IPv6) src-addr, -| ... | dst-addr and MAC addresses. -| ... | *[Ref] Applicable standard specifications:* RFC7348. - -*** Variables *** -| ${vni_1}= | 23 -| ${vni_2}= | 35 - -| ${bd_id1}= | 10 -| ${bd_id2}= | 20 -| ${bd_id3}= | 30 -| ${shg1}= | 1 -| ${shg2}= | 2 - -| ${ip4_addr1}= | 172.16.0.1 -| ${ip4_addr2}= | 172.16.0.2 -| ${ip4_prefix}= | 24 - -| ${ip6_addr1}= | 3ffe:64::1 -| ${ip6_addr2}= | 3ffe:64::2 -| ${ip6_prefix}= | 64 - -| ${sock1}= | /tmp/sock1 -| ${sock2}= | /tmp/sock2 - -| ${qemu1}= | qemu_instance_1 -| ${qemu2}= | qemu_instance_2 - -| ${dut1_vhost1}= | dut1_vhost_if1 -| ${dut1_vhost2}= | dut1_vhost_if2 -| ${dut2_vhost1}= | dut2_vhost_if1 -| ${dut2_vhost2}= | dut2_vhost_if2 - -*** Test Cases *** -| TC01: DUT1 and DUT2 with L2BD and VXLANoIPv4 tunnels switch ICMPv4 between TG links -| | [Documentation] -| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-VXLAN-Eth-IPv4-ICMPv4 on \ -| | ... | DUT1-DUT2; Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 and DUT2 -| | ... | configure two i/fs into L2BD with MAC learning. [Ver] Make TG -| | ... | verify ICMPv4 Echo Req pkts are switched thru DUT1 and DUT2 in -| | ... | both directions and are correct on receive. [Ref] RFC7348. -| | Given Path for 3-node testing is set -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Interfaces in 3-node path are up -| | ${dut1_to_dut2_name}= | Get interface name | ${dut1_node} | ${dut1_to_dut2} -| | ${dut2_to_dut1_name}= | Get interface name | ${dut2_node} | ${dut2_to_dut1} -| | And IP addresses are set on interfaces | ${dut1_node} | ${dut1_to_dut2_name} | ${NONE} -| | ... | ${dut2_node} | ${dut2_to_dut1_name} | ${NONE} -| | ${dut1s_vxlan}= | When Create VXLAN interface | ${dut1_node} | ${vni_1} -| | | ... | ${dut1s_ip_address} | ${dut2s_ip_address} -| | And Interfaces are added to BD | ${dut1_node} | ${bd_id1} -| | ... | ${dut1_to_tg} | ${dut1s_vxlan} -| | ${dut2s_vxlan}= | And Create VXLAN interface | ${dut2_node} | ${vni_1} -| | | ... | ${dut2s_ip_address} | ${dut1s_ip_address} -| | And Interfaces are added to BD | ${dut2_node} | ${bd_id1} -| | ... | ${dut2_to_tg} | ${dut2s_vxlan} -| | Then Send and receive ICMPv4 bidirectionally -| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} - -| TC02: DUT1 and DUT2 with L2BD and VXLANoIPv4 tunnels in SHG switch ICMPv4 between TG links -| | [Documentation] -| | ... | [Top] TG=DUT1=DUT2=TG. [Enc] Eth-IPv4-VXLAN-Eth-IPv4-ICMPv4 on \ -| | ... | DUT1-DUT2; Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 configure L2 -| | ... | bridge-domain (MAC learning enabled) with two untagged interfaces -| | ... | to TG and two VXLAN interfaces towards the DUT2 and put both VXLAN -| | ... | interfaces into the same Split-Horizon-Group (SHG). On DUT2 configure -| | ... | two L2 bridge-domain (MAC learning enabled), each with one untagged -| | ... | interface to TG and one VXLAN interface towards the DUT1. [Ver] Make -| | ... | TG send ICMPv4 Echo Reqs between all four of its interfaces to be -| | ... | switched by DUT1 and DUT2; verify packets are not switched between -| | ... | TG interfaces connected to DUT2 that are isolated by SHG on DUT1. -| | ... | [Ref] RFC7348. -| | [Tags] | 3_NODE_DOUBLE_LINK_TOPO -| | Given Path for 3-node BD-SHG testing is set | ${nodes['TG']} -| | ... | ${nodes['DUT1']} -| | ... | ${nodes['DUT2']} -| | And Interfaces in 3-node BD-SHG testing are up -| | And Set Interface Address | ${dut1_node} | ${dut1_to_dut2} | ${ip4_addr1} -| | ... | ${ip4_prefix} -| | And Set Interface Address | ${dut2_node} | ${dut2_to_dut1} | ${ip4_addr2} -| | ... | ${ip4_prefix} -| | And VPP IP Probe | ${dut1_node} | ${dut1_to_dut2} | ${ip4_addr2} -| | And VPP IP Probe | ${dut2_node} | ${dut2_to_dut1} | ${ip4_addr1} -| | ${dut1s_vxlan1}= | When Create VXLAN interface | ${dut1_node} | ${vni_1} -| | | ... | ${ip4_addr1} | ${ip4_addr2} -| | ${dut1s_vxlan2}= | And Create VXLAN interface | ${dut1_node} | ${vni_2} -| | | ... | ${ip4_addr1} | ${ip4_addr2} -| | ${dut2s_vxlan1}= | And Create VXLAN interface | ${dut2_node} | ${vni_1} -| | | ... | ${ip4_addr2} | ${ip4_addr1} -| | ${dut2s_vxlan2}= | And Create VXLAN interface | ${dut2_node} | ${vni_2} -| | | ... | ${ip4_addr2} | ${ip4_addr1} -| | And Set Interface State | ${dut1_node} | ${dut1s_vxlan1} | up -| | And Set Interface State | ${dut1_node} | ${dut1s_vxlan2} | up -| | And Set Interface State | ${dut2_node} | ${dut2s_vxlan1} | up -| | And Set Interface State | ${dut2_node} | ${dut2s_vxlan2} | up -| | And Vpp Node Interfaces Ready Wait | ${dut1_node} -| | And Vpp Node Interfaces Ready Wait | ${dut2_node} -| | And Bridge domain on DUT node is created | ${dut1_node} | ${bd_id1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1_to_tg_if1} -| | ... | ${bd_id1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1_to_tg_if2} -| | ... | ${bd_id1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1s_vxlan1} -| | ... | ${bd_id1} | ${shg1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1s_vxlan2} -| | ... | ${bd_id1} | ${shg1} -| | And Bridge domain on DUT node is created | ${dut2_node} | ${bd_id2} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2_to_tg_if1} -| | ... | ${bd_id2} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2s_vxlan1} -| | ... | ${bd_id2} -| | And Bridge domain on DUT node is created | ${dut2_node} | ${bd_id3} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2_to_tg_if2} -| | ... | ${bd_id3} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2s_vxlan2} -| | ... | ${bd_id3} -| | Then Send and receive ICMPv4 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if1} -| | ... | ${tg_to_dut2_if1} -| | And Send and receive ICMPv4 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if1} -| | ... | ${tg_to_dut2_if2} -| | And Send and receive ICMPv4 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if2} -| | ... | ${tg_to_dut2_if1} -| | And Send and receive ICMPv4 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if2} -| | ... | ${tg_to_dut2_if2} -| | And Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send and receive ICMPv4 bidirectionally -| | | ... | ${tg_node} | ${tg_to_dut2_if1} -| | | ... | ${tg_to_dut2_if2} - -| TC03: DUT1 and DUT2 with L2BD and VXLANoIPv4 tunnels in different SHGs switch ICMPv4 between TG links -| | [Documentation] -| | ... | [Top] TG=DUT1=DUT2=TG.[Enc] Eth-IPv4-VXLAN-Eth-IPv4-ICMPv4 on \ -| | ... | DUT1-DUT2; Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 configure L2 -| | ... | bridge-domain (MAC learning enabled) with two untagged interfaces -| | ... | to TG and two VXLAN interfaces towards the DUT2 and put both VXLAN -| | ... | interfaces into the different Split-Horizon-Group (SHGs). On DUT2 -| | ... | configure two L2 bridge-domain (MAC learning enabled), each with one -| | ... | untagged interface to TG and one VXLAN interface towards the DUT1. -| | ... | [Ver] Make TG send ICMPv4 Echo Req between all four of its interfaces -| | ... | to be switched by DUT1 and DUT2; verify packets are switched between -| | ... | all TG interfaces. [Ref] RFC7348. -| | [Tags] | 3_NODE_DOUBLE_LINK_TOPO -| | Given Path for 3-node BD-SHG testing is set | ${nodes['TG']} -| | ... | ${nodes['DUT1']} -| | ... | ${nodes['DUT2']} -| | And Interfaces in 3-node BD-SHG testing are up -| | And Set Interface Address | ${dut1_node} | ${dut1_to_dut2} | ${ip4_addr1} -| | ... | ${ip4_prefix} -| | And Set Interface Address | ${dut2_node} | ${dut2_to_dut1} | ${ip4_addr2} -| | ... | ${ip4_prefix} -| | And VPP IP Probe | ${dut1_node} | ${dut1_to_dut2} | ${ip4_addr2} -| | And VPP IP Probe | ${dut2_node} | ${dut2_to_dut1} | ${ip4_addr1} -| | ${dut1s_vxlan1}= | When Create VXLAN interface | ${dut1_node} | ${vni_1} -| | | ... | ${ip4_addr1} | ${ip4_addr2} -| | ${dut1s_vxlan2}= | And Create VXLAN interface | ${dut1_node} | ${vni_2} -| | | ... | ${ip4_addr1} | ${ip4_addr2} -| | ${dut2s_vxlan1}= | And Create VXLAN interface | ${dut2_node} | ${vni_1} -| | | ... | ${ip4_addr2} | ${ip4_addr1} -| | ${dut2s_vxlan2}= | And Create VXLAN interface | ${dut2_node} | ${vni_2} -| | | ... | ${ip4_addr2} | ${ip4_addr1} -| | And Set Interface State | ${dut1_node} | ${dut1s_vxlan1} | up -| | And Set Interface State | ${dut1_node} | ${dut1s_vxlan2} | up -| | And Set Interface State | ${dut2_node} | ${dut2s_vxlan1} | up -| | And Set Interface State | ${dut2_node} | ${dut2s_vxlan2} | up -| | And Vpp Node Interfaces Ready Wait | ${dut1_node} -| | And Vpp Node Interfaces Ready Wait | ${dut2_node} -| | And Bridge domain on DUT node is created | ${dut1_node} | ${bd_id1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1_to_tg_if1} -| | ... | ${bd_id1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1_to_tg_if2} -| | ... | ${bd_id1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1s_vxlan1} -| | ... | ${bd_id1} | ${shg1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1s_vxlan2} -| | ... | ${bd_id1} | ${shg2} -| | And Bridge domain on DUT node is created | ${dut2_node} | ${bd_id2} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2_to_tg_if1} -| | ... | ${bd_id2} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2s_vxlan1} -| | ... | ${bd_id2} -| | And Bridge domain on DUT node is created | ${dut2_node} | ${bd_id3} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2_to_tg_if2} -| | ... | ${bd_id3} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2s_vxlan2} -| | ... | ${bd_id3} -| | Then Send and receive ICMPv4 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if1} -| | ... | ${tg_to_dut2_if1} -| | And Send and receive ICMPv4 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if1} -| | ... | ${tg_to_dut2_if2} -| | And Send and receive ICMPv4 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if2} -| | ... | ${tg_to_dut2_if1} -| | And Send and receive ICMPv4 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if2} -| | ... | ${tg_to_dut2_if2} -| | And Send and receive ICMPv4 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut2_if1} -| | ... | ${tg_to_dut2_if2} - -| TC04: DUT1 and DUT2 with L2BD and VXLANoIPv6 tunnels switch ICMPv6 between TG links -| | [Documentation] -| | ... | [Top] TG=DUT1=DUT2=TG.[Enc] Eth-IPv6-VXLAN-Eth-IPv6-ICMPv6 on \ -| | ... | DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] On DUT1 and DUT2 -| | ... | configure L2 bridge-domain (MAC learning enabled), each with one -| | ... | interface to TG and one VXLAN tunnel interface towards the other -| | ... | DUT. [Ver] Make TG send ICMPv6 Echo Req between two of its -| | ... | interfaces to be switched by DUT1 and DUT2; verify all packets -| | ... | are received. [Ref] RFC7348. -| | [Tags] | 3_NODE_DOUBLE_LINK_TOPO -| | Given Path for 3-node testing is set -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Interfaces in 3-node path are up -| | And Set Interface Address | ${dut1_node} | ${dut1_to_dut2} | ${ip6_addr1} -| | ... | ${ip6_prefix} -| | And Set Interface Address | ${dut2_node} | ${dut2_to_dut1} | ${ip6_addr2} -| | ... | ${ip6_prefix} -| | And VPP IP Probe | ${dut1_node} | ${dut1_to_dut2} | ${ip6_addr2} -| | And VPP IP Probe | ${dut2_node} | ${dut2_to_dut1} | ${ip6_addr1} -| | ${dut1s_vxlan}= | When Create VXLAN interface | ${dut1_node} | ${vni_1} -| | | ... | ${ip6_addr1} | ${ip6_addr2} -| | And Interfaces are added to BD | ${dut1_node} | ${bd_id1} -| | ... | ${dut1_to_tg} | ${dut1s_vxlan} -| | ${dut2s_vxlan}= | And Create VXLAN interface | ${dut2_node} | ${vni_1} -| | | ... | ${ip6_addr2} | ${ip6_addr1} -| | And Interfaces are added to BD | ${dut2_node} | ${bd_id1} -| | ... | ${dut2_to_tg} | ${dut2s_vxlan} -| | Then Send and receive ICMPv6 bidirectionally -| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} - -| TC05: DUT1 and DUT2 with L2BD and VXLANoIPv6 tunnels in SHG switch ICMPv6 between TG links -| | [Documentation] -| | ... | [Top] TG=DUT1=DUT2=TG. [Enc] Eth-IPv6-VXLAN-Eth-IPv6-ICMPv6 on \ -| | ... | DUT1-DUT2; Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] On DUT1 configure L2 -| | ... | bridge-domain (MAC learning enabled) with two untagged interfaces -| | ... | to TG and two VXLAN interfaces towards the DUT2 and put both VXLAN -| | ... | interfaces into the same Split-Horizon-Group (SHG). On DUT2 configure -| | ... | two L2 bridge-domain (MAC learning enabled), each with one untagged -| | ... | interface to TG and one VXLAN interface towards the DUT1. [Ver] Make -| | ... | TG send ICMPv6 Echo Reqs between all four of its interfaces to be -| | ... | switched by DUT1 and DUT2; verify packets are not switched between -| | ... | TG interfaces connected to DUT2 that are isolated by SHG on DUT1. -| | ... | [Ref] RFC7348. -| | [Tags] | 3_NODE_DOUBLE_LINK_TOPO -| | Given Path for 3-node BD-SHG testing is set | ${nodes['TG']} -| | ... | ${nodes['DUT1']} -| | ... | ${nodes['DUT2']} -| | And Interfaces in 3-node BD-SHG testing are up -| | And Set Interface Address | ${dut1_node} | ${dut1_to_dut2} | ${ip6_addr1} -| | ... | ${ip6_prefix} -| | And Set Interface Address | ${dut2_node} | ${dut2_to_dut1} | ${ip6_addr2} -| | ... | ${ip6_prefix} -| | And VPP IP Probe | ${dut1_node} | ${dut1_to_dut2} | ${ip6_addr2} -| | And VPP IP Probe | ${dut2_node} | ${dut2_to_dut1} | ${ip6_addr1} -| | ${dut1s_vxlan1}= | When Create VXLAN interface | ${dut1_node} | ${vni_1} -| | | ... | ${ip6_addr1} | ${ip6_addr2} -| | ${dut1s_vxlan2}= | And Create VXLAN interface | ${dut1_node} | ${vni_2} -| | | ... | ${ip6_addr1} | ${ip6_addr2} -| | ${dut2s_vxlan1}= | And Create VXLAN interface | ${dut2_node} | ${vni_1} -| | | ... | ${ip6_addr2} | ${ip6_addr1} -| | ${dut2s_vxlan2}= | And Create VXLAN interface | ${dut2_node} | ${vni_2} -| | | ... | ${ip6_addr2} | ${ip6_addr1} -| | And Set Interface State | ${dut1_node} | ${dut1s_vxlan1} | up -| | And Set Interface State | ${dut1_node} | ${dut1s_vxlan2} | up -| | And Set Interface State | ${dut2_node} | ${dut2s_vxlan1} | up -| | And Set Interface State | ${dut2_node} | ${dut2s_vxlan2} | up -| | And Vpp Node Interfaces Ready Wait | ${dut1_node} -| | And Vpp Node Interfaces Ready Wait | ${dut2_node} -| | And Bridge domain on DUT node is created | ${dut1_node} | ${bd_id1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1_to_tg_if1} -| | ... | ${bd_id1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1_to_tg_if2} -| | ... | ${bd_id1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1s_vxlan1} -| | ... | ${bd_id1} | ${shg1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1s_vxlan2} -| | ... | ${bd_id1} | ${shg1} -| | And Bridge domain on DUT node is created | ${dut2_node} | ${bd_id2} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2_to_tg_if1} -| | ... | ${bd_id2} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2s_vxlan1} -| | ... | ${bd_id2} -| | And Bridge domain on DUT node is created | ${dut2_node} | ${bd_id3} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2_to_tg_if2} -| | ... | ${bd_id3} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2s_vxlan2} -| | ... | ${bd_id3} -| | Then Send and receive ICMPv6 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if1} -| | ... | ${tg_to_dut2_if1} -| | And Send and receive ICMPv6 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if1} -| | ... | ${tg_to_dut2_if2} -| | And Send and receive ICMPv6 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if2} -| | ... | ${tg_to_dut2_if1} -| | And Send and receive ICMPv6 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if2} -| | ... | ${tg_to_dut2_if2} -| | And Run Keyword And Expect Error | ICMP echo Rx timeout -| | ... | Send and receive ICMPv6 bidirectionally -| | | ... | ${tg_node} | ${tg_to_dut2_if1} -| | | ... | ${tg_to_dut2_if2} - -| TC06: DUT1 and DUT2 with L2BD and VXLANoIPv6 tunnels in different SHGs switch ICMPv6 between TG links -| | [Documentation] -| | ... | [Top] TG=DUT1=DUT2=TG.[Enc] Eth-IPv6-VXLAN-Eth-IPv6-ICMPv6 on \ -| | ... | DUT1-DUT2; Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] On DUT1 configure L2 -| | ... | bridge-domain (MAC learning enabled) with two untagged interfaces -| | ... | to TG and two VXLAN interfaces towards the DUT2 and put both VXLAN -| | ... | interfaces into the different Split-Horizon-Group (SHGs). On DUT2 -| | ... | configure two L2 bridge-domain (MAC learning enabled), each with one -| | ... | untagged interface to TG and one VXLAN interface towards the DUT1. -| | ... | [Ver] Make TG send ICMPv6 Echo Req between all four of its interfaces -| | ... | to be switched by DUT1 and DUT2; verify packets are switched between -| | ... | all TG interfaces. [Ref] RFC7348. -| | [Tags] | 3_NODE_DOUBLE_LINK_TOPO -| | Given Path for 3-node BD-SHG testing is set | ${nodes['TG']} -| | ... | ${nodes['DUT1']} -| | ... | ${nodes['DUT2']} -| | And Interfaces in 3-node BD-SHG testing are up -| | And Set Interface Address | ${dut1_node} | ${dut1_to_dut2} | ${ip6_addr1} -| | ... | ${ip6_prefix} -| | And Set Interface Address | ${dut2_node} | ${dut2_to_dut1} | ${ip6_addr2} -| | ... | ${ip6_prefix} -| | And VPP IP Probe | ${dut1_node} | ${dut1_to_dut2} | ${ip6_addr2} -| | And VPP IP Probe | ${dut2_node} | ${dut2_to_dut1} | ${ip6_addr1} -| | ${dut1s_vxlan1}= | When Create VXLAN interface | ${dut1_node} | ${vni_1} -| | | ... | ${ip6_addr1} | ${ip6_addr2} -| | ${dut1s_vxlan2}= | And Create VXLAN interface | ${dut1_node} | ${vni_2} -| | | ... | ${ip6_addr1} | ${ip6_addr2} -| | ${dut2s_vxlan1}= | And Create VXLAN interface | ${dut2_node} | ${vni_1} -| | | ... | ${ip6_addr2} | ${ip6_addr1} -| | ${dut2s_vxlan2}= | And Create VXLAN interface | ${dut2_node} | ${vni_2} -| | | ... | ${ip6_addr2} | ${ip6_addr1} -| | And Set Interface State | ${dut1_node} | ${dut1s_vxlan1} | up -| | And Set Interface State | ${dut1_node} | ${dut1s_vxlan2} | up -| | And Set Interface State | ${dut2_node} | ${dut2s_vxlan1} | up -| | And Set Interface State | ${dut2_node} | ${dut2s_vxlan2} | up -| | And Vpp Node Interfaces Ready Wait | ${dut1_node} -| | And Vpp Node Interfaces Ready Wait | ${dut2_node} -| | And Bridge domain on DUT node is created | ${dut1_node} | ${bd_id1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1_to_tg_if1} -| | ... | ${bd_id1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1_to_tg_if2} -| | ... | ${bd_id1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1s_vxlan1} -| | ... | ${bd_id1} | ${shg1} -| | And Interface is added to bridge domain | ${dut1_node} | ${dut1s_vxlan2} -| | ... | ${bd_id1} | ${shg2} -| | And Bridge domain on DUT node is created | ${dut2_node} | ${bd_id2} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2_to_tg_if1} -| | ... | ${bd_id2} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2s_vxlan1} -| | ... | ${bd_id2} -| | And Bridge domain on DUT node is created | ${dut2_node} | ${bd_id3} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2_to_tg_if2} -| | ... | ${bd_id3} -| | And Interface is added to bridge domain | ${dut2_node} | ${dut2s_vxlan2} -| | ... | ${bd_id3} -| | Then Send and receive ICMPv6 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if1} -| | ... | ${tg_to_dut2_if1} -| | And Send and receive ICMPv6 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if1} -| | ... | ${tg_to_dut2_if2} -| | And Send and receive ICMPv6 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if2} -| | ... | ${tg_to_dut2_if1} -| | And Send and receive ICMPv6 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut1_if2} -| | ... | ${tg_to_dut2_if2} -| | And Send and receive ICMPv6 bidirectionally | ${tg_node} -| | ... | ${tg_to_dut2_if1} -| | ... | ${tg_to_dut2_if2} - -| TC07:DUT1 and DUT2 with two L2BDs and VXLANoIPv4 tunnel switch ICMPv4 between TG links and VM links -| | [Documentation] -| | ... | [Top] TG-DUT1-VM-DUT1-DUT2-VM-DUT2-TG. -| | ... | [Enc] Eth-IPv4-VXLAN-Eth-IPv4-ICMPv4 on DUT1-DUT2; Eth-IPv4-ICMPv4 -| | ... | on TG-DUTn and DUTn=VM. -| | ... | [Cfg] On both DUTs configure two L2BDs (MAC learning enabled); first -| | ... | L2BD with untagged interface to TG and vhost-user interface to local -| | ... | VM, second one with vhost-user interface to local VM and VXLAN -| | ... | interface towards the other DUT. Configure linux bridge on both VMs -| | ... | to pass traffic between both vhost-user interfaces. -| | ... | [Ver] Make TG send ICMPv4 Echo Req between two of its interfaces to -| | ... | be switched by DUT1 and DUT2; verify packets are switched between -| | ... | these TG interfaces. -| | ... | [Ref] RFC7348. -| | [Tags] | VPP_VM_ENV -| | Given Path for 3-node testing is set -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Interfaces in 3-node path are up -| | When VPP Vhost interfaces for L2BD forwarding are setup | ${dut1_node} -| | ... | ${sock1} -| | ... | ${sock2} -| | ... | ${dut1_vhost1} -| | ... | ${dut1_vhost2} -| | And VPP Vhost interfaces for L2BD forwarding are setup | ${dut2_node} -| | ... | ${sock1} -| | ... | ${sock2} -| | ... | ${dut2_vhost1} -| | ... | ${dut2_vhost2} -| | And VM for Vhost L2BD forwarding is setup | ${dut1_node} | ${sock1} -| | ... | ${sock2} | ${qemu1} -| | And VM for Vhost L2BD forwarding is setup | ${dut2_node} | ${sock1} -| | ... | ${sock2} | ${qemu2} -| | And Set Interface Address | ${dut1_node} | ${dut1_to_dut2} | ${ip4_addr1} -| | ... | ${ip4_prefix} -| | And Set Interface Address | ${dut2_node} | ${dut2_to_dut1} | ${ip4_addr2} -| | ... | ${ip4_prefix} -| | And VPP IP Probe | ${dut1_node} | ${dut1_to_dut2} | ${ip4_addr2} -| | And VPP IP Probe | ${dut2_node} | ${dut2_to_dut1} | ${ip4_addr1} -| | ${dut1s_vxlan}= | And Create VXLAN interface | ${dut1_node} | ${vni_1} -| | | ... | ${ip4_addr1} | ${ip4_addr2} -| | ${dut2s_vxlan}= | And Create VXLAN interface | ${dut2_node} | ${vni_1} -| | | ... | ${ip4_addr2} | ${ip4_addr1} -| | And Interfaces are added to BD | ${dut1_node} | ${bd_id1} -| | ... | ${dut1_to_tg} | ${${dut1_vhost1}} -| | And Interfaces are added to BD | ${dut1_node} | ${bd_id2} -| | ... | ${dut1s_vxlan} | ${${dut1_vhost2}} -| | And Interfaces are added to BD | ${dut2_node} | ${bd_id1} -| | ... | ${dut2_to_tg} | ${${dut2_vhost1}} -| | And Interfaces are added to BD | ${dut2_node} | ${bd_id2} -| | ... | ${dut2s_vxlan} | ${${dut2_vhost2}} -| | Then Send and receive ICMPv4 bidirectionally -| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} -| | [Teardown] | Run Keywords | Show Packet Trace on All DUTs | ${nodes} -| | ... | AND | Show vpp trace dump on all DUTs -| | ... | AND | Run keyword | Qemu Teardown | ${dut1_node} -| | ... | ${${qemu1}} | ${qemu1} -| | ... | AND | Run keyword | Qemu Teardown | ${dut2_node} -| | ... | ${${qemu2}} | ${qemu2} -| | ... | AND | Check VPP PID in Teardown - -| TC08:DUT1 and DUT2 with two L2BDs and VXLANoIPv6 tunnel switch ICMPv6 between TG links and VM links -| | [Documentation] -| | ... | [Top] TG-DUT1-VM-DUT1-DUT2-VM-DUT2-TG. -| | ... | [Enc] Eth-IPv6-VXLAN-Eth-IPv6-ICMPv6 on DUT1-DUT2; Eth-IPv4-ICMPv4 -| | ... | on TG-DUTn and DUTn=VM. -| | ... | [Cfg] On both DUTs configure two L2BDs (MAC learning enabled); first -| | ... | L2BD with untagged interface to TG and vhost-user interface to local -| | ... | VM, second one with vhost-user interface to local VM and VXLAN -| | ... | interface towards the other DUT. Configure linux bridge on both VMs -| | ... | to pass traffic between both vhost-user interfaces. -| | ... | [Ver] Make TG send ICMPv6 Echo Req between two of its interfaces to -| | ... | be switched by DUT1 and DUT2; verify packets are switched between -| | ... | these TG interfaces. -| | ... | [Ref] RFC7348. -| | [Tags] | VPP_VM_ENV -| | Given Path for 3-node testing is set -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} -| | And Interfaces in 3-node path are up -| | When VPP Vhost interfaces for L2BD forwarding are setup | ${dut1_node} -| | ... | ${sock1} -| | ... | ${sock2} -| | ... | ${dut1_vhost1} -| | ... | ${dut1_vhost2} -| | And VPP Vhost interfaces for L2BD forwarding are setup | ${dut2_node} -| | ... | ${sock1} -| | ... | ${sock2} -| | ... | ${dut2_vhost1} -| | ... | ${dut2_vhost2} -| | And VM for Vhost L2BD forwarding is setup | ${dut1_node} | ${sock1} -| | ... | ${sock2} | ${qemu1} -| | And VM for Vhost L2BD forwarding is setup | ${dut2_node} | ${sock1} -| | ... | ${sock2} | ${qemu2} -| | And Set Interface Address | ${dut1_node} | ${dut1_to_dut2} | ${ip6_addr1} -| | ... | ${ip6_prefix} -| | And Set Interface Address | ${dut2_node} | ${dut2_to_dut1} | ${ip6_addr2} -| | ... | ${ip6_prefix} -| | And VPP IP Probe | ${dut1_node} | ${dut1_to_dut2} | ${ip4_addr2} -| | And VPP IP Probe | ${dut2_node} | ${dut2_to_dut1} | ${ip4_addr1} -| | ${dut1s_vxlan}= | And Create VXLAN interface | ${dut1_node} | ${vni_1} -| | | ... | ${ip6_addr1} | ${ip6_addr2} -| | ${dut2s_vxlan}= | And Create VXLAN interface | ${dut2_node} | ${vni_1} -| | | ... | ${ip6_addr2} | ${ip6_addr1} -| | And Interfaces are added to BD | ${dut1_node} | ${bd_id1} -| | ... | ${dut1_to_tg} | ${${dut1_vhost1}} -| | And Interfaces are added to BD | ${dut1_node} | ${bd_id2} -| | ... | ${dut1s_vxlan} | ${${dut1_vhost2}} -| | And Interfaces are added to BD | ${dut2_node} | ${bd_id1} -| | ... | ${dut2_to_tg} | ${${dut2_vhost1}} -| | And Interfaces are added to BD | ${dut2_node} | ${bd_id2} -| | ... | ${dut2s_vxlan} | ${${dut2_vhost2}} -| | Then Send and receive ICMPv6 bidirectionally -| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} -| | [Teardown] | Run Keywords | Show Packet Trace on All DUTs | ${nodes} -| | ... | AND | Show vpp trace dump on all DUTs -| | ... | AND | Run keyword | Qemu Teardown | ${dut1_node} -| | ... | ${${qemu1}} | ${qemu1} -| | ... | AND | Run keyword | Qemu Teardown | ${dut2_node} -| | ... | ${${qemu2}} | ${qemu2} -| | ... | AND | Check VPP PID in Teardown |