diff options
Diffstat (limited to 'tests/honeycomb/func/mgmt-cfg-routing-apihc-apivat-func.robot')
| -rw-r--r-- | tests/honeycomb/func/mgmt-cfg-routing-apihc-apivat-func.robot | 233 |
1 files changed, 233 insertions, 0 deletions
diff --git a/tests/honeycomb/func/mgmt-cfg-routing-apihc-apivat-func.robot b/tests/honeycomb/func/mgmt-cfg-routing-apihc-apivat-func.robot new file mode 100644 index 0000000000..540093fe07 --- /dev/null +++ b/tests/honeycomb/func/mgmt-cfg-routing-apihc-apivat-func.robot @@ -0,0 +1,233 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Library | resources.libraries.python.honeycomb.Routing.RoutingKeywords +| Library | resources.libraries.python.Trace +| Resource | resources/libraries/robot/shared/default.robot +| Resource | resources/libraries/robot/shared/testing_path.robot +| Resource | resources/libraries/robot/ip/ip4.robot +| Resource | resources/libraries/robot/ip/ip6.robot +| Resource | resources/libraries/robot/honeycomb/honeycomb.robot +| Resource | resources/libraries/robot/honeycomb/interfaces.robot +| Resource | resources/libraries/robot/honeycomb/routing.robot +| ... +| Test Setup | Clear Packet Trace on All DUTs | ${nodes} +| ... +| Suite Setup | Set Up Honeycomb Functional Test Suite | ${node} +| ... +| Suite Teardown | Tear Down Honeycomb Functional Test Suite | ${node} +| ... +| Test Teardown | Honeycomb routing test teardown | ${node} | ${table} +| ... +| Documentation | *Honeycomb routing test suite.* +| ... +| Force Tags | HC_FUNC + +*** Test Cases *** +| TC01: Single hop IPv4 route +| | [Documentation] +| | ... | [Top] TG=DUT1=TG. +| | ... | [Enc] Eth-IPv4-ICMP. +| | ... | [Cfg] (Using Honeycomb API) On DUT1 add ARP entries to both TG\ +| | ... | interfaces and configure route with TG-if2 as next-hop. +| | ... | [Ver] Send ICMP packet from first TG interface to configured route +| | ... | destination. Receive packet on the second TG interface. +| | ... +| | ${table}= | Set Variable | table1 +| | Given Setup interfaces and neighbors for IPv4 routing test +| | When Honeycomb configures routing table +| | ... | ${node} | table1 | ipv4 | ${table1} | ${1} +| | Then Routing data from Honeycomb should contain +| | ... | ${node} | table1 | ipv4 | ${table1_oper} +| | And Verify route IPv4 | ${nodes['TG']} +| | ... | ${src_ip} | ${dst_ip} +| | ... | ${tg_to_dut_if1} | ${tg_to_dut_if1_mac} +| | ... | ${tg_to_dut_if2} | ${dut_to_tg_if1_mac} + +| TC02: Multi hop IPv4 route +| | [Documentation] +| | ... | [Top] TG=DUT1=TG. +| | ... | [Enc] Eth-IPv4-ICMP. +| | ... | [Cfg] (Using Honeycomb API) On DUT1 add ARP entries to both TG\ +| | ... | interfaces and configure two routes through the second DUT interface. +| | ... | [Ver] Send 100 ICMP packets from first TG interface to configured +| | ... | route destination. Receive all packets on the second TG interface and\ +| | ... | verify that each destination MAC was used by exactly 50 packets. +| | ... | Receive packet on the second TG interface. +| | ... +| | ${table}= | Set Variable | table2 +| | Given Setup interfaces and neighbors for IPv4 routing test +| | And Honeycomb adds interface IPv4 neighbor | ${dut_node} | ${dut_to_tg_if2} +| | ... | ${next_hop1} | ${next_hop_mac1} +| | And Honeycomb adds interface IPv4 neighbor | ${dut_node} | ${dut_to_tg_if2} +| | ... | ${next_hop2} | ${next_hop_mac2} +| | When Honeycomb configures routing table +| | ... | ${node} | table2 | ipv4 | ${table2} | ${1} +| | Then Routing data from Honeycomb should contain +| | ... | ${node} | table2 | ipv4 | ${table2_oper} +| | And Verify multipath Route | ${nodes['TG']} +| | ... | ${src_ip} | ${dst_ip} +| | ... | ${tg_to_dut_if1} | ${tg_to_dut_if1_mac} +| | ... | ${tg_to_dut_if2} | ${dut_to_tg_if1_mac} +| | ... | ${dut_to_tg_if2_mac} | ${next_hop_mac1} | ${next_hop_mac2} + +| TC03: Special hop - blackhole IPv4 route +| | [Documentation] +| | ... | [Top] TG=DUT1=TG. +| | ... | [Enc] Eth-IPv4-ICMP. +| | ... | [Cfg] (Using Honeycomb API) On DUT1 add ARP entries to both TG\ +| | ... | interfaces and configure route with special rule blackhole. +| | ... | [Ver] Send ICMP packet from first TG interface to configured route +| | ... | destination. Make sure no packet is received on the second TG\ +| | ... | interface. +| | ... +| | ${table}= | Set Variable | table3 +| | Given Setup interfaces and neighbors for IPv4 routing test +| | When Honeycomb configures routing table +| | ... | ${node} | table3 | ipv4 | ${table3} | ${1} | special=${TRUE} +| | Then Routing data from Honeycomb should contain +| | ... | ${node} | table3 | ipv4 | ${table3_oper} +| | And Run keyword and Expect Error | ICMP echo Rx timeout +| | ... | Verify route IPv4 | ${nodes['TG']} +| | ... | ${src_ip} | ${dst_ip} +| | ... | ${tg_to_dut_if1} | ${tg_to_dut_if1_mac} +| | ... | ${tg_to_dut_if2} | ${dut_to_tg_if1_mac} + +| TC04: Single hop IPv6 route +| | [Documentation] +| | ... | [Top] TG=DUT1=TG. +| | ... | [Enc] Eth-IPv6-ICMPv6. +| | ... | [Cfg] (Using Honeycomb API) On DUT1 add ARP entries to both TG\ +| | ... | interfaces and configure route with TG-if2 as next-hop. +| | ... | [Ver] Send ICMP packet from first TG interface to configured route +| | ... | destination. Receive packet on the second TG interface. +| | ... +| | ${table}= | Set Variable | table4 +| | Given Setup interfaces and neighbors for IPv6 routing test +| | When Honeycomb configures routing table +| | ... | ${node} | table4 | ipv6 | ${table4} | ${1} +| | Then Routing data from Honeycomb should contain +| | ... | ${node} | table4 | ipv6 | ${table4_oper} +| | And Verify route IPv6 | ${nodes['TG']} +| | ... | ${src_ip} | ${next_hop} +| | ... | ${tg_to_dut_if1} | ${tg_to_dut_if1_mac} +| | ... | ${tg_to_dut_if2} | ${dut_to_tg_if1_mac} + +| TC05: Multi hop IPv6 route +| | [Documentation] +| | ... | [Top] TG=DUT1=TG. +| | ... | [Enc] Eth-IPv6-ICMPv6. +| | ... | [Cfg] (Using Honeycomb API) On DUT1 add ARP entries to both TG\ +| | ... | interfaces and configure two routes through the second DUT interface. +| | ... | [Ver] Send 100 ICMP packets from first TG interface to configured +| | ... | route destination. Receive all packets on the second TG interface and\ +| | ... | verify that each destination MAC was used by exactly 50 packets. +| | ... | Receive packet on the second TG interface. +| | ... +| | ${table}= | Set Variable | table5 +| | Given Setup interfaces and neighbors for IPv6 routing test +| | And Honeycomb adds interface IPv6 neighbor | ${dut_node} | ${dut_to_tg_if2} +| | ... | ${next_hop1} | ${next_hop_mac1} +| | And Honeycomb adds interface IPv6 neighbor | ${dut_node} | ${dut_to_tg_if2} +| | ... | ${next_hop2} | ${next_hop_mac2} +| | When Honeycomb configures routing table +| | ... | ${node} | table5 | ipv6 | ${table5} | ${1} +| | Then Routing data from Honeycomb should contain +| | ... | ${node} | table5 | ipv6 | ${table5_oper} +| | And Verify multipath Route | ${nodes['TG']} +| | ... | ${src_ip} | ${dst_ip} +| | ... | ${tg_to_dut_if1} | ${tg_to_dut_if1_mac} +| | ... | ${tg_to_dut_if2} | ${dut_to_tg_if1_mac} +| | ... | ${dut_to_tg_if2_mac} | ${next_hop_mac1} | ${next_hop_mac2} + +| TC06: Special hop - blackhole IPv6 route +| | [Documentation] +| | ... | [Top] TG=DUT1=TG. +| | ... | [Enc] Eth-IPv6-ICMPv6. +| | ... | [Cfg] (Using Honeycomb API) On DUT1 add ARP entries to both TG\ +| | ... | interfaces and configure route with special rule blackhole. +| | ... | [Ver] Send ICMP packet from first TG interface to configured route +| | ... | destination. Make sure no packet is received on the second TG\ +| | ... | interface. +| | ... +# HC2VPP-254 Operational data for Blackhole IPv6 route is incorrect +| | [Tags] | EXPECTED_FAILING +| | ${table}= | Set Variable | table6 +| | Given Setup interfaces and neighbors for IPv6 routing test +| | When Honeycomb configures routing table +| | ... | ${node} | table6 | ipv6 | ${table6} | ${1} | special=${TRUE} +| | Then Routing data from Honeycomb should contain +| | ... | ${node} | table6 | ipv6 | ${table6_oper} +| | And Run keyword and Expect Error | ICMP echo Rx timeout +| | ... | Verify route IPv6 | ${nodes['TG']} +| | ... | ${src_ip} | ${dst_ip} +| | ... | ${tg_to_dut_if1} | ${tg_to_dut_if1_mac} +| | ... | ${tg_to_dut_if2} | ${dut_to_tg_if1_mac} + +*** Keywords *** +| Setup interfaces and neighbors for IPv4 routing test +| | Configure path in 2-node circular topology +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['TG']} +| | Import Variables | resources/test_data/honeycomb/routing.py +| | ... | ${nodes['DUT1']} | ipv4 | ${dut_to_tg_if2} +| | Setup vrf IDs | ${dut_node} | ${dut_to_tg_if1} | ${1} +| | Setup vrf IDs | ${dut_node} | ${dut_to_tg_if2} | ${1} +| | Honeycomb configures interface state | ${dut_node} | ${dut_to_tg_if1} | up +| | Honeycomb configures interface state | ${dut_node} | ${dut_to_tg_if2} | up +| | Honeycomb sets interface IPv4 address with prefix | ${dut_node} +| | ... | ${dut_to_tg_if1} | ${dut_to_tg_if1_ip} | ${prefix_len} +| | Honeycomb sets interface IPv4 address with prefix | ${dut_node} +| | ... | ${dut_to_tg_if2} | ${dut_to_tg_if2_ip} | ${prefix_len} +| | Honeycomb adds interface IPv4 neighbor | ${dut_node} | ${dut_to_tg_if1} +| | ... | ${src_ip} | ${tg_to_dut_if1_mac} +| | Honeycomb adds interface IPv4 neighbor | ${dut_node} | ${dut_to_tg_if2} +| | ... | ${next_hop} | ${tg_to_dut_if2_mac} + +| Setup interfaces and neighbors for IPv6 routing test +| | Configure path in 2-node circular topology +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['TG']} +| | Import Variables | resources/test_data/honeycomb/routing.py +| | ... | ${nodes['DUT1']} | ipv6 | ${dut_to_tg_if2} +| | Honeycomb sets interface VRF ID +| | ... | ${dut_node} | ${dut_to_tg_if1} | ${1} | ipv6 +| | Honeycomb sets interface VRF ID +| | ... | ${dut_node} | ${dut_to_tg_if2} | ${1} | ipv6 +| | Honeycomb configures interface state | ${dut_node} | ${dut_to_tg_if1} | up +| | Honeycomb configures interface state | ${dut_node} | ${dut_to_tg_if2} | up +| | Honeycomb sets interface IPv6 address | ${dut_node} +| | ... | ${dut_to_tg_if1} | ${dut_to_tg_if1_ip} | ${prefix_len} +| | Honeycomb sets interface IPv6 address | ${dut_node} +| | ... | ${dut_to_tg_if2} | ${dut_to_tg_if2_ip} | ${prefix_len} +| | Honeycomb adds interface IPv6 neighbor | ${dut_node} | ${dut_to_tg_if1} +| | ... | ${src_ip} | ${tg_to_dut_if1_mac} +| | Honeycomb adds interface IPv6 neighbor | ${dut_node} | ${dut_to_tg_if2} +| | ... | ${next_hop} | ${tg_to_dut_if2_mac} +| | Vpp all ra suppress link layer | ${nodes} + +| Honeycomb routing test teardown +| | ... +| | [arguments] | ${node} | ${routing_table} +| | ... +| | Show Packet Trace on All DUTs | ${nodes} +| | Log routing configuration from VAT | ${node} +| | Honeycomb removes routing configuration | ${node} | ${routing_table} + +| Setup vrf IDs +| | ... +| | [Arguments] | ${node} | ${interface} | ${vrf} +| | ... +| | Honeycomb sets interface VRF ID +| | ... | ${node} | ${interface} | ${vrf} | ipv4 +| | Honeycomb sets interface VRF ID +| | ... | ${node} | ${interface} | ${vrf} | ipv6
\ No newline at end of file |