diff options
Diffstat (limited to 'tests/perf/10ge2p1x520-dot1q-l2xcbase-ndrpdrdisc.robot')
| -rw-r--r-- | tests/perf/10ge2p1x520-dot1q-l2xcbase-ndrpdrdisc.robot | 584 |
1 files changed, 0 insertions, 584 deletions
diff --git a/tests/perf/10ge2p1x520-dot1q-l2xcbase-ndrpdrdisc.robot b/tests/perf/10ge2p1x520-dot1q-l2xcbase-ndrpdrdisc.robot deleted file mode 100644 index d99d772c8f..0000000000 --- a/tests/perf/10ge2p1x520-dot1q-l2xcbase-ndrpdrdisc.robot +++ /dev/null @@ -1,584 +0,0 @@ -# Copyright (c) 2017 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance_setup.robot -| Resource | resources/libraries/robot/tagging.robot -| ... -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC -| ... | NIC_Intel-X520-DA2 | L2XCFWD | BASE | DOT1Q -| Suite Setup | Set up 3-node performance topology with DUT's NIC model -| ... | L2 | Intel-X520-DA2 -| Suite Teardown | Tear down 3-node performance topology -| ... -| ... -| Test Setup | Set up performance test -| ... -| Test Teardown | Tear down performance discovery test | ${min_rate}pps -| ... | ${framesize} | ${traffic_profile} -| ... -| Documentation | *RFC2544: Pkt throughput L2XC with 802.1q test cases* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. 802.1q -| ... | tagging is applied on link between DUT1 and DUT2. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- -| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. -| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop -| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop -| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage -| ... | of packets transmitted. NDR and PDR are discovered for different -| ... | Ethernet L2 frame sizes using either binary search or linear search -| ... | algorithms with configured starting rate and final step that determines -| ... | throughput measurement resolution. Test packets are generated by TG on -| ... | links to DUTs. TG traffic profile contains two L3 flow-groups -| ... | (flow-group per direction, 253 flows per flow-group) with all packets -| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static -| ... | payload. MAC addresses are matching MAC addresses of the TG node -| ... | interfaces. -| ... | *[Ref] Applicable standard specifications:* RFC2544. - -*** Variables *** -| ${subid}= | 10 -| ${tag_rewrite}= | pop-1 -# X520-DA2 bandwidth limit -| ${s_limit} | ${10000000000} -# Traffic profile: -| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 - -*** Test Cases *** -| tc01-64B-1t1c-dot1q-l2xcbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames -| | ... | using binary search start at 10GE linerate, step 100kpps. -| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc02-64B-1t1c-dot1q-l2xcbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames -| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. -| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc03-1518B-1t1c-dot1q-l2xcbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames -| | ... | using binary search start at 10GE linerate, step 10kpps. -| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc04-1518B-1t1c-dot1q-l2xcbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames -| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. -| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc05-9000B-1t1c-dot1q-l2xcbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames -| | ... | using binary search start at 10GE linerate, step 5kpps. -| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc06-9000B-1t1c-dot1q-l2xcbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames -| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. -| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc07-64B-2t2c-dot1q-l2xcbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames -| | ... | using binary search start at 10GE linerate, step 100kpps. -| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc08-64B-2t2c-dot1q-l2xcbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames -| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. -| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc09-1518B-2t2c-dot1q-l2xcbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames -| | ... | using binary search start at 10GE linerate, step 10kpps. -| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc10-1518B-2t2c-dot1q-l2xcbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames -| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. -| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc11-9000B-2t2c-dot1q-l2xcbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames -| | ... | using binary search start at 10GE linerate, step 5kpps. -| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc12-9000B-2t2c-dot1q-l2xcbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames -| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. -| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc13-64B-4t4c-dot1q-l2xcbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames -| | ... | using binary search start at 10GE linerate, step 100kpps. -| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc14-64B-4t4c-dot1q-l2xcbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames -| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. -| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc15-1518B-4t4c-dot1q-l2xcbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames -| | ... | using binary search start at 10GE linerate, step 10kpps. -| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc16-1518B-4t4c-dot1q-l2xcbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames -| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. -| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc17-9000B-4t4c-dot1q-l2xcbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames -| | ... | using binary search start at 10GE linerate, step 5kpps. -| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc18-9000B-4t4c-dot1q-l2xcbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames -| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. -| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} |