1 files changed, 737 insertions, 0 deletions
diff --git a/tests/perf/10ge2p1x520-ethip4-ip4base-iacldstbase-ndrpdrdisc.robot b/tests/perf/10ge2p1x520-ethip4-ip4base-iacldstbase-ndrpdrdisc.robot
new file mode 100644
index 0000000000..ee33e0761a
--- /dev/null
+++ b/tests/perf/10ge2p1x520-ethip4-ip4base-iacldstbase-ndrpdrdisc.robot
@@ -0,0 +1,737 @@
+# Copyright (c) 2017 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance.robot
+| Library | resources.libraries.python.Classify.Classify
+| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']}
+| ... | WITH NAME | dut1_v4
+| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']}
+| ... | WITH NAME | dut2_v4
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ... | NIC_Intel-X520-DA2 | ETH | IP4FWD | FEATURE | IACLDST
+| ...
+| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model
+| ... | L3 | Intel-X520-DA2
+| Suite Teardown | 3-node Performance Suite Teardown
+| ...
+| Test Setup | Performance test setup
+| Test Teardown | Performance test teardown | ${min_rate}pps | ${framesize}
+| ... | 3-node-IPv4
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 iAcl whitelist test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
+| ... | routing, two static IPv4 /24 routes and IPv4 iAcl security whitelist
+| ... | ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG.
+| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using either binary search or linear search
+| ... | algorithms with configured starting rate and final step that determines
+| ... | throughput measurement resolution. Test packets are generated by TG on
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
+| ... | (flow-group per direction, 253 flows per flow-group) with all packets
+| ... | containing Ethernet header, IPv4 header with IP protocol=61 and
+| ... | static payload. MAC addresses are matching MAC addresses of the TG
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit} | ${10000000000}
+
+*** Test Cases ***
+| tc01-64B-1t1c-ethip4-ip4base-iacldstbase-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR
+| | ... | for 64 Byte frames using binary search start at 10GE linerate,
+| | ... | step 100kpps.
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| tc02-64B-1t1c-ethip4-ip4base-iacldstbase-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR
+| | ... | for 64 Byte frames using binary search start at 10GE linerate,
+| | ... | step 100kpps, LT=0.5%.
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${perf_pdr_loss_acceptance}
+| | ...                                       | ${perf_pdr_loss_acceptance_type}
+
+| tc03-1518B-1t1c-ethip4-ip4base-iacldstbase-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR
+| | ... | for 1518 Byte frames using binary search start at 10GE linerate,
+| | ... | step 10kpps.
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| tc04-1518B-1t1c-ethip4-ip4base-iacldstbase-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR
+| | ... | for 1518 Byte frames using binary search start at 10GE linerate,
+| | ... | step 10kpps, LT=0.5%.
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${perf_pdr_loss_acceptance}
+| | ...                                       | ${perf_pdr_loss_acceptance_type}
+
+| tc05-9000B-1t1c-ethip4-ip4base-iacldstbase-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR
+| | ... | for 9000 Byte frames using binary search start at 10GE linerate,
+| | ... | step 5kpps.
+| | [Tags] | 1T1C | STHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| tc06-9000B-1t1c-ethip4-ip4base-iacldstbase-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR
+| | ... | for 9000 Byte frames using binary search start at 10GE linerate,
+| | ... | step 5kpps, LT=0.5%.
+| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${perf_pdr_loss_acceptance}
+| | ...                                       | ${perf_pdr_loss_acceptance_type}
+
+| tc07-64B-2t2c-ethip4-ip4base-iacldstbase-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR
+| | ... | for 64 Byte frames using binary search start at 10GE linerate,
+| | ... | step 100kpps.
+| | [Tags] | 2T2C | MTHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| tc08-64B-2t2c-ethip4-ip4base-iacldstbase-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR
+| | ... | for 64 Byte frames using binary search start at 10GE linerate,
+| | ... | step 100kpps, LT=0.5%.
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${perf_pdr_loss_acceptance}
+| | ...                                       | ${perf_pdr_loss_acceptance_type}
+
+| tc09-1518B-2t2c-ethip4-ip4base-iacldstbase-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR
+| | ... | for 1518 Byte frames using binary search start at 10GE linerate,
+| | ... | step 10kpps.
+| | [Tags] | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| tc10-1518B-2t2c-ethip4-ip4base-iacldstbase-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR
+| | ... | for 1518 Byte frames using binary search start at 10GE linerate,
+| | ... | step 10kpps, LT=0.5%.
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${perf_pdr_loss_acceptance}
+| | ...                                       | ${perf_pdr_loss_acceptance_type}
+
+| tc11-9000B-2t2c-ethip4-ip4base-iacldstbase-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR
+| | ... | for 9000 Byte frames using binary search start at 10GE linerate,
+| | ... | step 5kpps.
+| | [Tags] | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| tc12-9000B-2t2c-ethip4-ip4base-iacldstbase-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR
+| | ... | for 9000 Byte frames using binary search start at 10GE linerate,
+| | ... | step 5kpps, LT=0.5%.
+| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${perf_pdr_loss_acceptance}
+| | ...                                       | ${perf_pdr_loss_acceptance_type}
+
+| tc13-64B-4t4c-ethip4-ip4base-iacldstbase-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR
+| | ... | for 64 Byte frames using binary search start at 10GE linerate,
+| | ... | step 100kpps.
+| | [Tags] | 4T4C | MTHREAD | NDRDISC
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| tc14-64B-4t4c-ethip4-ip4base-iacldstbase-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR
+| | ... | for 64 Byte frames using binary search start at 10GE linerate,
+| | ... | step 100kpps, LT=0.5%.
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${64}
+| | ${min_rate}= | Set Variable | ${100000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${perf_pdr_loss_acceptance}
+| | ...                                       | ${perf_pdr_loss_acceptance_type}
+
+| tc15-1518B-4t4c-ethip4-ip4base-iacldstbase-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR
+| | ... | for 1518 Byte frames using binary search start at 10GE linerate,
+| | ... | step 10kpps.
+| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| tc16-1518B-4t4c-ethip4-ip4base-iacldstbase-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR
+| | ... | for 1518 Byte frames using binary search start at 10GE linerate,
+| | ... | step 10kpps, LT=0.5%.
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${1518}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${perf_pdr_loss_acceptance}
+| | ...                                       | ${perf_pdr_loss_acceptance_type}
+
+| tc17-9000B-4t4c-ethip4-ip4base-iacldstbase-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR
+| | ... | for 9000 Byte frames using binary search start at 10GE linerate,
+| | ... | step 5kpps.
+| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+
+| tc18-9000B-4t4c-ethip4-ip4base-iacldstbase-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
+| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR
+| | ... | for 9000 Byte frames using binary search start at 10GE linerate,
+| | ... | step 5kpps, LT=0.5%.
+| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ${framesize}= | Set Variable | ${9000}
+| | ${min_rate}= | Set Variable | ${10000}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo
+| | And   Add PCI devices to DUTs from 3-node single link topology
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv4 forwarding initialized in a 3-node circular topology
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut1} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 20.20.20.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
+| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
+| | ... | ${dut2} | ip4 | dst
+| | And Vpp Configures Classify Session L3
+| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
+| | ... | ip4 | dst | 10.10.10.2
+| | And Vpp Enable Input Acl Interface
+| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ...                                       | ${binary_max} | 3-node-IPv4
+| | ...                                       | ${min_rate} | ${max_rate}
+| | ...                                       | ${threshold}
+| | ...                                       | ${perf_pdr_loss_acceptance}
+| | ...                                       | ${perf_pdr_loss_acceptance_type}