diff options
Diffstat (limited to 'tests/perf/10ge2p1x520-ethip4-ip4base-ipolicemarkbase-ndrchk.robot')
| -rw-r--r-- | tests/perf/10ge2p1x520-ethip4-ip4base-ipolicemarkbase-ndrchk.robot | 228 |
1 files changed, 228 insertions, 0 deletions
diff --git a/tests/perf/10ge2p1x520-ethip4-ip4base-ipolicemarkbase-ndrchk.robot b/tests/perf/10ge2p1x520-ethip4-ip4base-ipolicemarkbase-ndrchk.robot new file mode 100644 index 0000000000..125b1e68d0 --- /dev/null +++ b/tests/perf/10ge2p1x520-ethip4-ip4base-ipolicemarkbase-ndrchk.robot @@ -0,0 +1,228 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance.robot +| Library | resources.libraries.python.Policer +| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']} | WITH NAME | dut1_v4 +| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']} | WITH NAME | dut2_v4 +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PERFTEST_SHORT +| ... | NIC_Intel-X520-DA2 +| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | 3-node Performance Suite Teardown +| Test Setup | Setup all DUTs before test +| Test Teardown | Run Keywords | Remove startup configuration of VPP from all DUTs +| ... | AND | Show vpp trace dump on all DUTs +| Documentation | *Reference NDR throughput IPv4 policer verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4 +| ... | routing and two static IPv4 /24 route entries and policer with 2R3C +| ... | color-aware configuration. Policer is applied on links TG - DUT1 and +| ... | DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT configuration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 +| ... | and static payload. MAC addresses are matching MAC addresses of the +| ... | TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC2698. + +*** Variables *** +| ${cir}= | ${100} +| ${eir}= | ${150} + +*** Test Cases *** +| TC01: Verify 64B ref-NDR at 2x 3.1Mpps - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy \ +| | ... | core, 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 \ +| | ... | Byte frames using single trial throughput test. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR +| | ${framesize}= | Set Variable | 64 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 3.1mpps +| | Set Test Variable | ${cb} | ${framesize} +| | Set Test Variable | ${eb} | ${framesize} +| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC02: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy \ +| | ... | core, 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 \ +| | ... | Byte frames using single trial throughput test. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR +| | ${framesize}= | Set Variable | 1518 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 812743pps +| | Set Test Variable | ${cb} | ${framesize} +| | Set Test Variable | ${eb} | ${framesize} +| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When IPv4 forwarding initialized in a 3-node circular topology +| | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC03: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv4 2r3c-ca policer - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy \ +| | ... | core, 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 \ +| | ... | Byte frames using single trial throughput test. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR +| | ${framesize}= | Set Variable | 9000 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 138580pps +| | Set Test Variable | ${cb} | ${framesize} +| | Set Test Variable | ${eb} | ${framesize} +| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC04: Verify 64B ref-NDR at 2x 5.6Mpps - DUT IPv4 2r3c-ca policer - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 \ +| | ... | phy cores, 1 receive queue per NIC port. [Ver] Verify ref-NDR for \ +| | ... | 64 Byte frames using single trial throughput test. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR +| | ${framesize}= | Set Variable | 64 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 5.6mpps +| | Set Test Variable | ${cb} | ${framesize} +| | Set Test Variable | ${eb} | ${framesize} +| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC05: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv4 2r3c-ca policer - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 \ +| | ... | phy cores, 1 receive queue per NIC port. [Ver] Verify ref-NDR for \ +| | ... | 1518 Byte frames using single trial throughput test. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR +| | ${framesize}= | Set Variable | 1518 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 812743pps +| | Set Test Variable | ${cb} | ${framesize} +| | Set Test Variable | ${eb} | ${framesize} +| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC06: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv4 2r3c-ca policer - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 \ +| | ... | phy cores, 1 receive queue per NIC port. [Ver] Verify ref-NDR for \ +| | ... | 9000 Byte frames using single trial throughput test. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR +| | ${framesize}= | Set Variable | 9000 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 138580pps +| | Set Test Variable | ${cb} | ${framesize} +| | Set Test Variable | ${eb} | ${framesize} +| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC07: Verify 64B ref-NDR at 2x 8.9Mpps - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing and policer config with 4 thread, 4 \ +| | ... | phy core, 2 receive queue per NIC port. [Ver] Verify ref-NDR for 64 \ +| | ... | Byte frames using single trial throughput test. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR +| | ${framesize}= | Set Variable | 64 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 8.9mpps +| | Set Test Variable | ${cb} | ${framesize} +| | Set Test Variable | ${eb} | ${framesize} +| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC08: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing and policer config with 4 thread, 4 \ +| | ... | phy core, 2 receive queue per NIC port. [Ver] Verify ref-NDR for \ +| | ... | 1518 Byte frames using single trial throughput test. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR +| | ${framesize}= | Set Variable | 1518 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 812743pps +| | Set Test Variable | ${cb} | ${framesize} +| | Set Test Variable | ${eb} | ${framesize} +| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC09: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv4 2r3c-ca policer - 4threads 4cores 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing and policer config with 4 thread, 4 \ +| | ... | phy core, 2 receive queue per NIC port. [Ver] Verify ref-NDR for \ +| | ... | 9000 Byte frames using single trial throughput test. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR +| | ${framesize}= | Set Variable | 9000 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 138580pps +| | Set Test Variable | ${cb} | ${framesize} +| | Set Test Variable | ${eb} | ${framesize} +| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | And IPv4 policer 2r3c-'ca' initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 |