diff options
Diffstat (limited to 'tests/perf/10ge2p1x520-ethip4-ip4base-ndrchk.robot')
| -rw-r--r-- | tests/perf/10ge2p1x520-ethip4-ip4base-ndrchk.robot | 198 |
1 files changed, 198 insertions, 0 deletions
diff --git a/tests/perf/10ge2p1x520-ethip4-ip4base-ndrchk.robot b/tests/perf/10ge2p1x520-ethip4-ip4base-ndrchk.robot new file mode 100644 index 0000000000..73efd44ced --- /dev/null +++ b/tests/perf/10ge2p1x520-ethip4-ip4base-ndrchk.robot @@ -0,0 +1,198 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance.robot +| Library | resources.libraries.python.topology.Topology +| Library | resources.libraries.python.NodePath +| Library | resources.libraries.python.InterfaceUtil +| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']} | WITH NAME | dut1_v4 +| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']} | WITH NAME | dut2_v4 +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PERFTEST_SHORT +| ... | NIC_Intel-X520-DA2 | PERFTEST_BASE +| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | 3-node Performance Suite Teardown +| Test Setup | Setup all DUTs before test +| Test Teardown | Run Keywords | Remove startup configuration of VPP from all DUTs +| ... | AND | Show vpp trace dump on all DUTs +| Documentation | *Reference NDR throughput IPv4 routing verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4 +| ... | routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with +| ... | 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT configuration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 +| ... | and static payload. MAC addresses are matching MAC addresses of the +| ... | TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Test Cases *** +| TC01: Verify 64B ref-NDR at 2x 3.5Mpps - DUT IPv4 - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR +| | ${framesize}= | Set Variable | 64 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 3.5mpps +| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC02: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv4 - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR +| | ${framesize}= | Set Variable | 1518 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 812743pps +| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC03: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv4 - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR +| | ${framesize}= | Set Variable | 9000 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 138580pps +| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC04: Verify 64B ref-NDR at 2x 7.5Mpps - DUT IPv4 - 2threads, 2cores, 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR +| | ${framesize}= | Set Variable | 64 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 7.5mpps +| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC05: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv4 - 2threads, 2cores, 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR +| | ${framesize}= | Set Variable | 1518 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 812743pps +| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC06: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv4 - 2threads, 2cores, 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR +| | ${framesize}= | Set Variable | 9000 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 138580pps +| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC07: Verify 64B ref-NDR at 2x 10.0Mpps - DUT IPv4 - 4threads, 4cores, 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR +| | ${framesize}= | Set Variable | 64 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 10.0mpps +| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC08: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv4 - 4threads, 4cores, 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR +| | ${framesize}= | Set Variable | 1518 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 812743pps +| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 + +| TC09: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv4 - 4threads, 4cores, 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR +| | ${framesize}= | Set Variable | 9000 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 138580pps +| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And IPv4 forwarding initialized in a 3-node circular topology +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv4 |