diff options
Diffstat (limited to 'tests/perf/10ge2p1x520-ethip4lispip6-ip4base-ndrpdrdisc.robot')
| -rw-r--r-- | tests/perf/10ge2p1x520-ethip4lispip6-ip4base-ndrpdrdisc.robot | 596 |
1 files changed, 0 insertions, 596 deletions
diff --git a/tests/perf/10ge2p1x520-ethip4lispip6-ip4base-ndrpdrdisc.robot b/tests/perf/10ge2p1x520-ethip4lispip6-ip4base-ndrpdrdisc.robot deleted file mode 100644 index 356750ae8f..0000000000 --- a/tests/perf/10ge2p1x520-ethip4lispip6-ip4base-ndrpdrdisc.robot +++ /dev/null @@ -1,596 +0,0 @@ -# Copyright (c) 2017 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance_setup.robot -| Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot -| Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py -| ... -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC -| ... | NIC_Intel-X520-DA2 | IP4FWD | ENCAP | LISP | IP6UNRLAY | IP4OVRLAY -| ... -| Suite Setup | Set up 3-node performance topology with DUT's NIC model -| ... | L3 | Intel-X520-DA2 -| Suite Teardown | Tear down 3-node performance topology -| ... -| Test Setup | Set up performance test -| ... -| Test Teardown | Tear down performance discovery test | ${min_rate}pps -| ... | ${framesize} | ${traffic_profile} -| ... -| Documentation | *RFC6830: Pkt throughput Lisp test cases* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ -| ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISP-IPv6 on DUT1-DUT2 and\ -| ... | Eth-IPv4 on TG-DUTn for IPv4 routing over LISPoIPv6 tunnel.\ -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\ -| ... | routing and static routes. LISPoIPv6 tunnel is configured\ -| ... | between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520\ -| ... | Niantic by Intel. -| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ -| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ -| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ -| ... | of packets transmitted. NDR and PDR are discovered for different\ -| ... | Ethernet L2 frame sizes using either binary search or linear search\ -| ... | *[Ref] Applicable standard specifications:* RFC6830. - -*** Variables *** -# X520-DA2 bandwidth limit -| ${s_limit} | ${10000000000} -# Traffic profile: -| ${traffic_profile} | trex-sl-3n-ethip4-ip4src253 - -*** Test Cases *** -| tc01-64B-1t1c-ethip4lispip6-ip4base-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\ -| | ... | port. -| | ... | [Ver] Find NDR for 64 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 100kpps. -| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc02-64B-1t1c-ethip4lispip6-ip4base-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\ -| | ... | port. -| | ... | [Ver] Find PDR for 64 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 100kpps, LT=0.5%. -| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc03-1460B-1t1c-ethip4lispip6-ip4base-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\ -| | ... | port. -| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 100kpps. -| | [Tags] | 1460B | 1T1C | STHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${1460} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc04-1460B-1t1c-ethip4lispip6-ip4base-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\ -| | ... | port. -| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 10kpps, LT=0.5%. -| | [Tags] | 1460B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1460} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc05-9000B-1t1c-ethip4lispip6-ip4base-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\ -| | ... | port. -| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 5kpps. -| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc06-9000B-1t1c-ethip4lispip6-ip4base-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\ -| | ... | port. -| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 5kpps, LT=0.5%. -| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc07-64B-2t2c-ethip4lispip6-ip4base-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\ -| | ... | port. -| | ... | [Ver] Find NDR for 64 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 100kpps. -| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc08-64B-2t2c-ethip4lispip6-ip4base-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\ -| | ... | port. -| | ... | [Ver] Find PDR for 64 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 100kpps. -| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc09-1460B-2t2c-ethip4lispip6-ip4base-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\ -| | ... | port. -| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 10kpps. -| | [Tags] | 1460B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1460} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc10-1460B-2t2c-ethip4lispip6-ip4base-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\ -| | ... | port. -| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 10kpps, LT=0.5%. -| | [Tags] | 1460B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1460} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc11-9000B-2t2c-ethip4lispip6-ip4base-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\ -| | ... | port. -| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 5kpps. -| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc12-9000B-2t2c-ethip4lispip6-ip4base-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\ -| | ... | port. -| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 5kpps, LT=0.5%. -| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc13-64B-4t4c-ethip4lispip6-ip4base-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\ -| | ... | port. -| | ... | [Ver] Find NDR for 64 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 100kpps. -| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc14-64B-4t4c-ethip4lispip6-ip4base-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\ -| | ... | port. -| | ... | [Ver] Find PDR for 64 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 100kpps, LT=0.5%. -| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc15-1460B-4t4c-ethip4lispip6-ip4base-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\ -| | ... | port. -| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 10kpps. -| | [Tags] | 1460B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1460} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc16-1460B-4t4c-ethip4lispip6-ip4base-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\ -| | ... | port. -| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 10kpps, LT=0.5%. -| | [Tags] | 1460B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1460} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc17-9000B-4t4c-ethip4lispip6-ip4base-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\ -| | ... | port. -| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 5kpps. -| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc18-9000B-4t4c-ethip4lispip6-ip4base-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\ -| | ... | port. -| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start\ -| | ... | at 10GE linerate, step 5kpps, LT=0.5%. -| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 48} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6} -| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid} -| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency} -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} |