diff options
Diffstat (limited to 'tests/perf/10ge2p1x520-ethip6-ip6base-copwhtlistbase-ndrpdrdisc.robot')
| -rw-r--r-- | tests/perf/10ge2p1x520-ethip6-ip6base-copwhtlistbase-ndrpdrdisc.robot | 565 |
1 files changed, 0 insertions, 565 deletions
diff --git a/tests/perf/10ge2p1x520-ethip6-ip6base-copwhtlistbase-ndrpdrdisc.robot b/tests/perf/10ge2p1x520-ethip6-ip6base-copwhtlistbase-ndrpdrdisc.robot deleted file mode 100644 index fa5879507a..0000000000 --- a/tests/perf/10ge2p1x520-ethip6-ip6base-copwhtlistbase-ndrpdrdisc.robot +++ /dev/null @@ -1,565 +0,0 @@ -# Copyright (c) 2017 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance_setup.robot -| Library | resources.libraries.python.Cop -| ... -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC -| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | FEATURE | COPWHLIST -| ... -| Suite Setup | Set up 3-node performance topology with DUT's NIC model -| ... | L3 | Intel-X520-DA2 -| Suite Teardown | Tear down 3-node performance topology -| ... -| Test Setup | Set up performance test -| ... -| Test Teardown | Tear down performance discovery test | ${min_rate}pps -| ... | ${framesize} | ${traffic_profile} -| ... -| Documentation | *RFC2544: Pkt throughput IPv6 whitelist test cases* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 -| ... | routing, two static IPv6 /64 routes and IPv6 COP security whitelist -| ... | ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. -| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. -| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop -| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop -| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage -| ... | of packets transmitted. NDR and PDR are discovered for different -| ... | Ethernet L2 frame sizes using either binary search or linear search -| ... | algorithms with configured starting rate and final step that determines -| ... | throughput measurement resolution. Test packets are generated by TG on -| ... | links to DUTs. TG traffic profile contains two L3 flow-groups -| ... | (flow-group per direction, 253 flows per flow-group) with all packets -| ... | containing Ethernet header, IPv6 header and static -| ... | payload. MAC addresses are matching MAC addresses of the TG node -| ... | interfaces. -| ... | *[Ref] Applicable standard specifications:* RFC2544. - -*** Variables *** -# X520-DA2 bandwidth limit -| ${s_limit} | ${10000000000} -# Traffic profile: -| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253 - -*** Test Cases *** -| tc01-78B-1t1c-ethip6-ip6base-copwhtlistbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR -| | ... | for 78 Byte frames using binary search start at 10GE linerate, -| | ... | step 100kpps. -| | [Tags] | 78B | 1T1C | STHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${78} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc02-78B-1t1c-ethip6-ip6base-copwhtlistbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR -| | ... | for 78 Byte frames using binary search start at 10GE linerate, -| | ... | step 100kpps, LT=0.5%. -| | [Tags] | 78B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${78} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc03-1518B-1t1c-ethip6-ip6base-copwhtlistbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR -| | ... | for 1518 Byte frames using binary search start at 10GE linerate, -| | ... | step 10kpps. -| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc04-1518B-1t1c-ethip6-ip6base-copwhtlistbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR -| | ... | for 1518 Byte frames using binary search start at 10GE linerate, -| | ... | step 10kpps, LT=0.5%. -| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc05-9000B-1t1c-ethip6-ip6base-copwhtlistbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR -| | ... | for 9000 Byte frames using binary search start at 10GE linerate, -| | ... | step 5kpps. -| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc06-9000B-1t1c-ethip6-ip6base-copwhtlistbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR -| | ... | for 9000 Byte frames using binary search start at 10GE linerate, -| | ... | step 5kpps, LT=0.5%. -| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc07-78B-2t2c-ethip6-ip6base-copwhtlistbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR -| | ... | for 78 Byte frames using binary search start at 10GE linerate, -| | ... | step 100kpps. -| | [Tags] | 78B | 2T2C | MTHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${78} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc08-78B-2t2c-ethip6-ip6base-copwhtlistbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR -| | ... | for 78 Byte frames using binary search start at 10GE linerate, -| | ... | step 100kpps, LT=0.5%. -| | [Tags] | 78B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${78} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc09-1518B-2t2c-ethip6-ip6base-copwhtlistbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR -| | ... | for 1518 Byte frames using binary search start at 10GE linerate, -| | ... | step 10kpps. -| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc10-1518B-2t2c-ethip6-ip6base-copwhtlistbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR -| | ... | for 1518 Byte frames using binary search start at 10GE linerate, -| | ... | step 10kpps, LT=0.5%. -| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc11-9000B-2t2c-ethip6-ip6base-copwhtlistbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR -| | ... | for 9000 Byte frames using binary search start at 10GE linerate, -| | ... | step 5kpps. -| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc12-9000B-2t2c-ethip6-ip6base-copwhtlistbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR -| | ... | for 9000 Byte frames using binary search start at 10GE linerate, -| | ... | step 5kpps, LT=0.5%. -| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc13-78B-4t4c-ethip6-ip6base-copwhtlistbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR -| | ... | for 78 Byte frames using binary search start at 10GE linerate, -| | ... | step 100kpps. -| | [Tags] | 78B | 4T4C | MTHREAD | NDRDISC -| | ${framesize}= | Set Variable | ${78} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc14-78B-4t4c-ethip6-ip6base-copwhtlistbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR -| | ... | for 78 Byte frames using binary search start at 10GE linerate, -| | ... | step 100kpps, LT=0.5%. -| | [Tags] | 78B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${78} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc15-1518B-4t4c-ethip6-ip6base-copwhtlistbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR -| | ... | for 1518 Byte frames using binary search start at 10GE linerate, -| | ... | step 10kpps. -| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc16-1518B-4t4c-ethip6-ip6base-copwhtlistbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR -| | ... | for 1518 Byte frames using binary search start at 10GE linerate, -| | ... | step 10kpps, LT=0.5%. -| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -| tc17-9000B-4t4c-ethip6-ip6base-copwhtlistbase-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR -| | ... | for 9000 Byte frames using binary search start at 10GE linerate, -| | ... | step 5kpps. -| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc18-9000B-4t4c-ethip6-ip6base-copwhtlistbase-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ -| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR -| | ... | for 9000 Byte frames using binary search start at 10GE linerate, -| | ... | step 5kpps, LT=0.5%. -| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding in 3-node circular topology -| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local -| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local -| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 -| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 -| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable -| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} |