diff options
Diffstat (limited to 'tests/perf/10ge2p1x520-ethip6lispip6-ip6Base-pdrchk.robot')
| -rw-r--r-- | tests/perf/10ge2p1x520-ethip6lispip6-ip6Base-pdrchk.robot | 193 |
1 files changed, 193 insertions, 0 deletions
diff --git a/tests/perf/10ge2p1x520-ethip6lispip6-ip6Base-pdrchk.robot b/tests/perf/10ge2p1x520-ethip6lispip6-ip6Base-pdrchk.robot new file mode 100644 index 0000000000..3278c7137d --- /dev/null +++ b/tests/perf/10ge2p1x520-ethip6lispip6-ip6Base-pdrchk.robot @@ -0,0 +1,193 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance.robot +| Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot +| Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PDRCHK +| ... | NIC_Intel-X520-DA2 | IP6FWD | ENCAP | LISP | IP6UNRLAY | IP6OVRLAY +| ... +| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | 3-node Performance Suite Teardown +| ... +| Test Setup | Performance test setup +| Test Teardown | Performance pdrchk test teardown +| ... +| Documentation | *Reference PDR throughput Lisp tunnel verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6-LISP-IPv6 on DUT1-DUT2,\ +| ... | Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv6 tunnel. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6\ +| ... | routing and static routes. LISPoIPv6 tunnel is configured\ +| ... | between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520\ +| ... | Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies\ +| ... | DUTs' throughput at ref-PDR (reference Non Drop Rate) with zero packet\ +| ... | loss tolerance. Ref-PDR value is periodically updated acording to\ +| ... | formula: ref-PDR = 0.9x PDR, where PDR is found in RFC2544 long\ +| ... | performance tests for the same DUT confiiguration. Test packets are\ +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3\ +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with\ +| ... | all packets containing Ethernet header, IPv6 header with\ +| ... | IP protocol=61 and generated payload. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253 + +*** Keywords *** +| Check PDR for Lisp IPv6 over IPv6 forwarding +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with ${wt} thread, ${wt} phy core,\ +| | ... | ${rxq} receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for ${framesize} Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Arguments] | ${framesize} | ${rate} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${rate} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and rxqueues '${rxq}' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Traffic should pass with partial loss | ${perf_trial_duration} +| | ... | ${rate} | ${framesize} | ${traffic_profile} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-78B-1t1c-ethip6lispip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 78B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for Lisp IPv6 over IPv6 forwarding +| | framesize=${78} | rate=1.56mpps | wt=1 | rxq=1 + +| tc02-1460B-1t1c-ethip6lispip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1460B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for Lisp IPv6 over IPv6 forwarding +| | framesize=${1460} | rate=740000pps | wt=1 | rxq=1 + +| tc03-9000B-1t1c-ethip6lispip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for Lisp IPv6 over IPv6 forwarding +| | framesize=${9000} | rate=120000pps | wt=1 | rxq=1 + +| tc04-78B-2t2c-ethip6lispip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 78B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for Lisp IPv6 over IPv6 forwarding +| | framesize=${78} | rate=3.2mpps | wt=2 | rxq=1 + +| tc05-1460B-2t2c-ethip6lispip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1460B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for Lisp IPv6 over IPv6 forwarding +| | framesize=${1460} | rate=740000pps | wt=2 | rxq=1 + +| tc06-9000B-2t2c-ethip6lispip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for Lisp IPv6 over IPv6 forwarding +| | framesize=${9000} | rate=120000pps | wt=2 | rxq=1 + +| tc07-78B-4t4c-ethip6lispip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 78B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for Lisp IPv6 over IPv6 forwarding +| | framesize=${78} | rate=3.2mpps | wt=4 | rxq=2 + +| tc08-1460B-4t4c-ethip6lispip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1460B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for Lisp IPv6 over IPv6 forwarding +| | framesize=${1460} | rate=740000pps | wt=4 | rxq=2 + +| tc09-9000B-4t4c-ethip6lispip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for Lisp IPv6 over IPv6 forwarding +| | framesize=${9000} | rate=120000pps | wt=4 | rxq=2 |