diff options
Diffstat (limited to 'tests/perf/10ge2p1x520-ethip6lispip6-ip6base-ndrchk.robot')
| -rw-r--r-- | tests/perf/10ge2p1x520-ethip6lispip6-ip6base-ndrchk.robot | 269 |
1 files changed, 269 insertions, 0 deletions
diff --git a/tests/perf/10ge2p1x520-ethip6lispip6-ip6base-ndrchk.robot b/tests/perf/10ge2p1x520-ethip6lispip6-ip6base-ndrchk.robot new file mode 100644 index 0000000000..bd18ec321a --- /dev/null +++ b/tests/perf/10ge2p1x520-ethip6lispip6-ip6base-ndrchk.robot @@ -0,0 +1,269 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance.robot +| Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot +# import additional Lisp settings from resource file +| Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PERFTEST_SHORT +| ... | NIC_Intel-X520-DA2 | PERFTEST_ENCAP | LISP +| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | 3-node Performance Suite Teardown +| Test Setup | Setup all DUTs before test +| Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs +| Documentation | *Reference NDR throughput Lisp tunnel verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6-LISP-IPv6 on DUT1-DUT2,\ +| ... | Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv6 tunnel. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6\ +| ... | routing and static routes. LISPoIPv6 tunnel is configured\ +| ... | between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520\ +| ... | Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies\ +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet\ +| ... | loss tolerance. Ref-NDR value is periodically updated acording to\ +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long\ +| ... | performance tests for the same DUT confiiguration. Test packets are\ +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3\ +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with\ +| ... | all packets containing Ethernet header, IPv6 header with\ +| ... | IP protocol=61 and generated payload. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Test Cases *** +| TC01: Verify 78B ref-NDR at 2x 1.56Mpps - DUT IPv6 - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\ +| | ... | throughput test. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6 +| | ${framesize}= | Set Variable | 78 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 1.56mpps +| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv6 + +| TC02: Verify 1460B ref-NDR at 2x 740kpps - DUT IPv6 - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial\ +| | ... | throughput test. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6 +| | ${framesize}= | Set Variable | 1460 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 740000pps +| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv6 + +| TC03: Verify 9000B ref-NDR at 2x 120kpps - DUT IPv6 - 1thread 1core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6 +| | ${framesize}= | Set Variable | 9000 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 120000pps +| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv6 + +| TC04: Verify 78B ref-NDR at 2x 3.2Mpps - DUT IPv6 - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\ +| | ... | throughput test. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6 +| | ${framesize}= | Set Variable | 78 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 3.2mpps +| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv6 + +| TC05: Verify 1460B ref-NDR at 2x 740kpps - DUT IPv6 - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial\ +| | ... | throughput test. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6 +| | ${framesize}= | Set Variable | 1460 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 740000pps +| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv6 + +| TC06: Verify 9000B ref-NDR at 2x 120kpps - DUT IPv6 - 2thread 2core 1rxq +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6 +| | ${framesize}= | Set Variable | 9000 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 120000pps +| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv6 + +| TC07: Verify 78B ref-NDR at 2x 3.2Mpps - DUT IPv6 - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\ +| | ... | throughput test. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6 +| | ${framesize}= | Set Variable | 78 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 3.2mpps +| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv6 + +| TC08: Verify 1460B ref-NDR at 2x 740kpps - DUT IPv6 - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Verify ref-NDR for 1460 Byte frames using single trial\ +| | ... | throughput test. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6 +| | ${framesize}= | Set Variable | 1460 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 740000pps +| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Add No Multi Seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv6 + +| TC09: Verify 9000B ref-NDR at 2x 120kpps - DUT IPv6 - 4thread 4core 2rxq +| | [Documentation] +| | ... | [Cfg] DUT runs LISP tunnel config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6 +| | ${framesize}= | Set Variable | 9000 +| | ${duration}= | Set Variable | 10 +| | ${rate}= | Set Variable | 120000pps +| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo +| | And Add PCI devices to DUTs from 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Lisp IPv6 forwarding initialized in a 3-node circular topology +| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6} +| | ... | ${dut2_to_tg_ip6} | ${prefix6} +| | And Set up Lisp topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid} +| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency} +| | Then Traffic should pass with no loss | ${duration} | ${rate} +| | ... | ${framesize} | 3-node-IPv6 + |