diff options
Diffstat (limited to 'tests/perf/40ge2p1vic1385-eth-l2bdbasemaclrn-ndrdisc.robot')
| -rw-r--r-- | tests/perf/40ge2p1vic1385-eth-l2bdbasemaclrn-ndrdisc.robot | 349 |
1 files changed, 0 insertions, 349 deletions
diff --git a/tests/perf/40ge2p1vic1385-eth-l2bdbasemaclrn-ndrdisc.robot b/tests/perf/40ge2p1vic1385-eth-l2bdbasemaclrn-ndrdisc.robot deleted file mode 100644 index 879bfa427b..0000000000 --- a/tests/perf/40ge2p1vic1385-eth-l2bdbasemaclrn-ndrdisc.robot +++ /dev/null @@ -1,349 +0,0 @@ -# Copyright (c) 2017 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance.robot -| Library | resources.libraries.python.NodePath -| ... -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC -| ... | NIC_Cisco-VIC-1385 | ETH | L2BDMACLRN | BASE -| ... -| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model -| ... | L2 | Cisco-VIC-1385 -| Suite Teardown | 3-node Performance Suite Teardown -| ... -| Test Setup | Performance test setup -| Test Teardown | Performance test teardown | ${min_rate}pps | ${framesize} -| ... | 3-node-bridge -| ... -| Documentation | *RFC2544: Pkt throughput L2BD test cases* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- -| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p40GE NIC -| ... | NIC_Cisco-VIC-1385. -| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop -| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop -| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage -| ... | of packets transmitted. NDR and PDR are discovered for different -| ... | Ethernet L2 frame sizes using either binary search or linear search -| ... | algorithms with configured starting rate and final step that determines -| ... | throughput measurement resolution. Test packets are generated by TG on -| ... | links to DUTs. TG traffic profile contains two L3 flow-groups -| ... | (flow-group per direction, 253 flows per flow-group) with all packets -| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static -| ... | payload. MAC addresses are matching MAC addresses of the TG node -| ... | interfaces. -| ... | *[Ref] Applicable standard specifications:* RFC2544. - -*** Variables *** -# XL710-DA2 (TG) bandwidth limit ~49Gbps/2=24.5Gbps -| ${s_24.5G} | ${24500000000} -# XL710-DA2 Mpps (TG) limit 37.5Mpps/2=18.75Mpps -| ${s_18.75Mpps} | ${18750000} - -*** Test Cases *** -| tc01-64B-1t1c-eth-l2bdbasemaclrn-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\ -| | ... | 18.75Mpps rate, step 100kpps. -| | ... -| | [Tags] | 1T1C | STHREAD | NDRDISC -| | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Set Variable | ${s_18.75Mpps} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo -| | And Add PCI devices to DUTs from 3-node single link topology -| | And Add No Multi Seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And L2 bridge domain initialized in a 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} -| | ... | ${threshold} - -| tc02-64B-1t1c-eth-l2bdbasemaclrn-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at\ -| | ... | 18.75Mpps rate, step 100kpps. -| | ... -| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Set Variable | ${s_18.75Mpps} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo -| | And Add PCI devices to DUTs from 3-node single link topology -| | And Add No Multi Seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And L2 bridge domain initialized in a 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} -| | ... | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} - -| tc03-1518B-1t1c-eth-l2bdbasemaclrn-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\ -| | ... | 24.5G rate, step 10kpps. -| | ... -| | [Tags] | 1T1C | STHREAD | NDRDISC -| | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo -| | And Add PCI devices to DUTs from 3-node single link topology -| | And Add No Multi Seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And L2 bridge domain initialized in a 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} -| | ... | ${threshold} - -| tc05-9000B-1t1c-eth-l2bdbasemaclrn-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\ -| | ... | 24.5G rate, step 10kpps. -| | ... -| | [Tags] | 1T1C | STHREAD | NDRDISC -| | ... -| | ${framesize}= | Set Variable | ${9000} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo -| | And Add PCI devices to DUTs from 3-node single link topology -| | And Add No Multi Seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And L2 bridge domain initialized in a 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} -| | ... | ${threshold} - -| tc07-64B-2t2c-eth-l2bdbasemaclrn-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\ -| | ... | 18.75Mpps rate, step 100kpps. -| | ... -| | [Tags] | 2T2C | MTHREAD | NDRDISC -| | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Set Variable | ${s_18.75Mpps} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo -| | And Add PCI devices to DUTs from 3-node single link topology -| | And Add No Multi Seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And L2 bridge domain initialized in a 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} -| | ... | ${threshold} - -| tc08-64B-2t2c-eth-l2bdbasemaclrn-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at\ -| | ... | 18.75Mpps rate, step 100kpps. -| | ... -| | [Tags] | 2T2C | MTHREAD | PDR | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Set Variable | ${s_18.75Mpps} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo -| | And Add PCI devices to DUTs from 3-node single link topology -| | And Add No Multi Seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And L2 bridge domain initialized in a 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} -| | ... | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} - -| tc09-1518B-2t2c-eth-l2bdbasemaclrn-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\ -| | ... | 24.5G rate, step 10kpps. -| | ... -| | [Tags] | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo -| | And Add PCI devices to DUTs from 3-node single link topology -| | And Add No Multi Seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And L2 bridge domain initialized in a 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} -| | ... | ${threshold} - -| tc13-64B-4t4c-eth-l2bdbasemaclrn-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\ -| | ... | 2 receive queues per NIC port. -| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\ -| | ... | 18.75Mpps rate, step 100kpps. -| | ... -| | [Tags] | 4T4C | MTHREAD | NDRDISC -| | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Set Variable | ${s_18.75Mpps} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo -| | And Add PCI devices to DUTs from 3-node single link topology -| | And Add No Multi Seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And L2 bridge domain initialized in a 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} -| | ... | ${threshold} - -| tc15-1518B-4t4c-eth-l2bdbasemaclrn-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\ -| | ... | 2 receive queues per NIC port. -| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\ -| | ... | 24.5G rate, step 10kpps. -| | ... -| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${10000} -| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo -| | And Add PCI devices to DUTs from 3-node single link topology -| | And Add No Multi Seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And L2 bridge domain initialized in a 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} -| | ... | ${threshold} - -| tc19-IMIX-1t1c-eth-l2bdbasemaclrn-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at\ -| | ... | 24.5G rate, step 100kpps. -| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) -| | ... -| | [Tags] | 1T1C | STHREAD | NDRDISC -| | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo -| | And Add all PCI devices to all DUTs -| | And Add No Multi Seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And L2 bridge domain initialized in a 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} -| | ... | ${threshold} - -| tc20-IMIX-2t2c-eth-l2bdbasemaclrn-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD switching config with 2 thread, 2 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at\ -| | ... | 24.5G rate, step 100kpps. -| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) -| | ... -| | [Tags] | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rxqueues '1' in 3-node single-link topo -| | And Add all PCI devices to all DUTs -| | And Add No Multi Seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And L2 bridge domain initialized in a 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} -| | ... | ${threshold} - -| tc21-IMIX-4t4c-eth-l2bdbasemaclrn-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD switching config with 4 thread, 4 phy core,\ -| | ... | 2 receive queue per NIC port. -| | ... | [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at\ -| | ... | 24.5G rate, step 100kpps. -| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) -| | ... -| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rxqueues '2' in 3-node single-link topo -| | And Add all PCI devices to all DUTs -| | And Add No Multi Seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And L2 bridge domain initialized in a 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | 3-node-bridge | ${min_rate} | ${max_rate} -| | ... | ${threshold} |