aboutsummaryrefslogtreecommitdiffstats
path: root/tests/perf/Long_Lisp_Intel-X520-DA2.robot
diff options
context:
space:
mode:
Diffstat (limited to 'tests/perf/Long_Lisp_Intel-X520-DA2.robot')
-rw-r--r--tests/perf/Long_Lisp_Intel-X520-DA2.robot2328
1 files changed, 2328 insertions, 0 deletions
diff --git a/tests/perf/Long_Lisp_Intel-X520-DA2.robot b/tests/perf/Long_Lisp_Intel-X520-DA2.robot
new file mode 100644
index 0000000000..2ff8a582ab
--- /dev/null
+++ b/tests/perf/Long_Lisp_Intel-X520-DA2.robot
@@ -0,0 +1,2328 @@
+# Copyright (c) 2016 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance.robot
+| Resource | resources/libraries/robot/lisp/lisp_static_adjacency.robot
+| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']}
+| ... | WITH NAME | dut1_v4
+| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']}
+| ... | WITH NAME | dut2_v4
+# import additional Lisp settings from resource file
+| Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PERFTEST_LONG
+| ... | NIC_Intel-X520-DA2
+| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model
+| ... | L3 | Intel-X520-DA2
+| Suite Teardown | 3-node Performance Suite Teardown
+| Test Setup | Setup all DUTs before test
+| Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs
+| Documentation | *RFC6830: Pkt throughput Lisp test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2,
+| ... | Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel;
+| ... | Eth-IPv6-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for
+| ... | IPv6 routing over LISPoIPv6 tunnel; Eth-IPv6-LISP-IPv4-ICMPv4 on
+| ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv6
+| ... | tunnel; Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on
+| ... | TG-DUTn for IPv6 routing over LISPoIPv4 tunnel.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4 (IPv6)
+| ... | routing and static routes. LISPoIPv4 (oIPv6) tunnel is configured
+| ... | between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic
+| ... | by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using either binary search or linear search
+| ... | *[Ref] Applicable standard specifications:* RFC6830.
+
+*** Test Cases ***
+| TC01: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 64
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_72B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC02: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv4
+| | ${framesize}= | Set Variable | 64
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_72B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC03: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 1480 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1480
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC04: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port. [Ver] Find PDR for 1480 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv4
+| | ${framesize}= | Set Variable | 1480
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC05: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC06: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv4
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC07: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 64
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_72B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC08: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv4
+| | ${framesize}= | Set Variable | 64
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_72B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC09: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 1480 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1480
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC10: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 1480 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1480
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC11: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC12: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC13: 64B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 64
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_72B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC14: 64B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv4
+| | ${framesize}= | Set Variable | 64
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_72B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC15: 1480B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 1480 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1480
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC16: 1480B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 1480 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1480
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC17: 9000B NDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC18: 9000B PDR binary search - DUT IPv4 over LISPoIPv4 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
+| | ... | ${dut2_to_tg_ip4} | ${prefix4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
+| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC19: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 78 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 78
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_86B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC20: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 78 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv6
+| | ${framesize}= | Set Variable | 78
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_86B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC21: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC22: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv6
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC23: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC24: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv6
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC25: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 78 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 78
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_86B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC26: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 78 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv6
+| | ${framesize}= | Set Variable | 78
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_86B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC27: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC28: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC29: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC30: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC31: 78B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 78 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 78
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_86B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC32: 78B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 78 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv6
+| | ${framesize}= | Set Variable | 78
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_86B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC33: 1460B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC34: 1460B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_1488B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC35: 9000B NDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC36: 9000B PDR binary search - DUT IPv6 over LISPoIPv6 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_linerate_pps_9008B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6} | ${dut1_to_tg_ip6} | ${dut2_to_dut1_ip6}
+| | ... | ${dut2_to_tg_ip6} | ${prefix6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6_eid} | ${dut2_ip6_eid}
+| | ... | ${dut1_ip6_static_adjacency} | ${dut2_ip6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC37: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 64
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_112B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC38: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv4oIPv6
+| | ${framesize}= | Set Variable | 64
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_112B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC39: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC40: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv4oIPv6
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC41: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC42: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv4oIPv6
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC43: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 64
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_112B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC44: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv4oIPv6
+| | ${framesize}= | Set Variable | 64
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_112B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC45: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC46: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv4oIPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC47: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC48: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv4oIPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC49: 64B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 64 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 64
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_112B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC50: 64B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 64 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv4oIPv6
+| | ${framesize}= | Set Variable | 64
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_112B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC51: 1460B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC52: 1460B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 1460 Byte frames using binary search starlt
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv4oIPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC53: 9000B NDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv4oIPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC54: 9000B PDR binary search - DUT IPv4 over LISPoIPv6 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv4oIPv6 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip4o6} | ${dut1_to_tg_ip4o6} | ${dut2_to_dut1_ip4o6}
+| | ... | ${dut2_to_tg_ip4o6} | ${tg_prefix4o6} | ${dut_prefix4o6}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip4o6_eid} | ${dut2_ip4o6_eid}
+| | ... | ${dut1_ip4o6_static_adjacency} | ${dut2_ip4o6_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv4
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC55: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 78 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 78
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_126B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC56: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 78 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv6IPv4
+| | ${framesize}= | Set Variable | 78
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_126B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC57: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC58: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv6oIPv4
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC59: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC60: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | LISP_IPv6oIPv4
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC61: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 78 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 78
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_126B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC62: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 78 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv6oIPv4
+| | ${framesize}= | Set Variable | 78
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_126B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC63: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC64: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv6oIPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC65: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC66: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | LISP_IPv6oIPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC67: 78B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 78 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 78
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_126B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC68: 78B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 78 Byte frames using binary search start
+| | ... | at 10GE linerate, step 100kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv6oIPv4
+| | ${framesize}= | Set Variable | 78
+| | ${min_rate}= | Set Variable | 100000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_126B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC69: 1460B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC70: 1460B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 1460 Byte frames using binary search start
+| | ... | at 10GE linerate, step 10kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv6oIPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 1460
+| | ${min_rate}= | Set Variable | 10000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_1508B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Add No Multi Seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}
+
+| TC71: 9000B NDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | LISP_IPv6oIPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+
+| TC72: 9000B PDR binary search - DUT IPv6 over LISPoIPv4 tunnel - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist \
+| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC
+| | ... | port.
+| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start
+| | ... | at 10GE linerate, step 5kpps, LT=0.5%.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | LISP_IPv6oIPv4 | SKIP_PATCH
+| | ${framesize}= | Set Variable | 9000
+| | ${min_rate}= | Set Variable | 5000
+| | ${max_rate}= | Set Variable | ${10Ge_lisp_iph_linerate_pps_9048B}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And Add PCI devices to DUTs from 3-node single link topology
+| | And Apply startup configuration on all VPP DUTs
+| | When Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular topology
+| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4}
+| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4}
+| | And Set up Lisp topology
+| | ... | ${dut1} | ${dut1_if2} | ${NONE}
+| | ... | ${dut2} | ${dut2_if1} | ${NONE}
+| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid}
+| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency}
+| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
+| | ... | ${binary_max} | 3-node-IPv6
+| | ... | ${min_rate} | ${max_rate}
+| | ... | ${threshold}
+| | ... | ${glob_loss_acceptance}
+| | ... | ${glob_loss_acceptance_type}