1 files changed, 249 insertions, 0 deletions
diff --git a/tests/perf/Short_IPv6_Cop_Intel-X520-DA2.robot b/tests/perf/Short_IPv6_Cop_Intel-X520-DA2.robot
new file mode 100644
index 0000000000..5ef42c5a86
--- /dev/null
+++ b/tests/perf/Short_IPv6_Cop_Intel-X520-DA2.robot
@@ -0,0 +1,249 @@
+# Copyright (c) 2016 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance.robot
+| Library | resources.libraries.python.Cop
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PERFTEST_SHORT
+| ...        | NIC_Intel-X520-DA2
+| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model
+| ... | L3 | Intel-X520-DA2
+| Suite Teardown | 3-node Performance Suite Teardown
+| Test Setup | Setup all DUTs before test
+| Test Teardown | Run Keywords | Remove startup configuration of VPP from all DUTs
+| ...           | AND          | Show vpp trace dump on all DUTs
+| Documentation | *Reference NDR throughput IPv6 whitelist verify test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6
+| ... | routing, two static IPv6 /64 routes and IPv6 COP security whitelist
+| ... | ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG.
+| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In short performance tests, TG verifies
+| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet
+| ... | loss tolerance. Ref-NDR value is periodically updated acording to
+| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long
+| ... | performance tests for the same DUT configuration. Test packets are
+| ... | generated by TG on links to DUTs. TG traffic profile contains two L3
+| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with
+| ... | all packets containing Ethernet header, IPv6 header and generated
+| ... | payload. MAC addresses are matching MAC addresses of the TG node
+| ... | interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Test Cases ***
+| TC01: Verify 78B ref-NDR at 2x 2.8Mpps - DUT IPv6 whitelist - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 78 Byte frames using single trial throughput test.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
+| | ${framesize}= | Set Variable | 78
+| | ${duration}= | Set Variable | 10
+| | ${rate}= | Set Variable | 2.8mpps
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And   Add all PCI devices to all DUTs
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv6 forwarding initialized in a 3-node circular topology
+| | And   Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local
+| | And   Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local
+| | And   COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1
+| | And   COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1
+| | And   COP interface enable or disable | ${dut1} | ${dut1_if1} | enable
+| | And   COP interface enable or disable | ${dut2} | ${dut2_if2} | enable
+| | Then  Traffic should pass with no loss | ${duration} | ${rate}
+| | ...                                    | ${framesize} | 3-node-IPv6
+
+| TC02: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 whitelist - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 1518 Byte frames using single trial throughput test.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
+| | ${framesize}= | Set Variable | 1518
+| | ${duration}= | Set Variable | 10
+| | ${rate}= | Set Variable | 812743pps
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And   Add all PCI devices to all DUTs
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv6 forwarding initialized in a 3-node circular topology
+| | And   Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local
+| | And   Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local
+| | And   COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1
+| | And   COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1
+| | And   COP interface enable or disable | ${dut1} | ${dut1_if1} | enable
+| | And   COP interface enable or disable | ${dut2} | ${dut2_if2} | enable
+| | Then  Traffic should pass with no loss | ${duration} | ${rate}
+| | ...                                    | ${framesize} | 3-node-IPv6
+
+| TC03: Verify 9000B ref-NDR at 2x 138.580kpps - DUT IPv6 whitelist - 1thread 1core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 9000 Byte frames using single trial throughput test.
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
+| | ${framesize}= | Set Variable | 9000
+| | ${duration}= | Set Variable | 10
+| | ${rate}= | Set Variable | 138580pps
+| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
+| | And   Add all PCI devices to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv6 forwarding initialized in a 3-node circular topology
+| | And   Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local
+| | And   Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local
+| | And   COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1
+| | And   COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1
+| | And   COP interface enable or disable | ${dut1} | ${dut1_if1} | enable
+| | And   COP interface enable or disable | ${dut2} | ${dut2_if2} | enable
+| | Then  Traffic should pass with no loss | ${duration} | ${rate}
+| | ...                                    | ${framesize} | 3-node-IPv6
+
+| TC04: Verify 78B ref-NDR at 2x 4.9Mpps - DUT IPv6 whitelist - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 78 Byte frames using single trial throughput test.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
+| | ${framesize}= | Set Variable | 78
+| | ${duration}= | Set Variable | 10
+| | ${rate}= | Set Variable | 4.9mpps
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And   Add all PCI devices to all DUTs
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv6 forwarding initialized in a 3-node circular topology
+| | And   Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local
+| | And   Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local
+| | And   COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1
+| | And   COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1
+| | And   COP interface enable or disable | ${dut1} | ${dut1_if1} | enable
+| | And   COP interface enable or disable | ${dut2} | ${dut2_if2} | enable
+| | Then  Traffic should pass with no loss | ${duration} | ${rate}
+| | ...                                    | ${framesize} | 3-node-IPv6
+
+| TC05: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 whitelist - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 1518 Byte frames using single trial throughput test.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
+| | ${framesize}= | Set Variable | 1518
+| | ${duration}= | Set Variable | 10
+| | ${rate}= | Set Variable | 812743pps
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And   Add all PCI devices to all DUTs
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv6 forwarding initialized in a 3-node circular topology
+| | And   Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local
+| | And   Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local
+| | And   COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1
+| | And   COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1
+| | And   COP interface enable or disable | ${dut1} | ${dut1_if1} | enable
+| | And   COP interface enable or disable | ${dut2} | ${dut2_if2} | enable
+| | Then  Traffic should pass with no loss | ${duration} | ${rate}
+| | ...                                    | ${framesize} | 3-node-IPv6
+
+| TC06: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv6 whitelist - 2thread 2core 1rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 9000 Byte frames using single trial throughput test.
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
+| | ${framesize}= | Set Variable | 9000
+| | ${duration}= | Set Variable | 10
+| | ${rate}= | Set Variable | 138580pps
+| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
+| | And   Add all PCI devices to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv6 forwarding initialized in a 3-node circular topology
+| | And   Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local
+| | And   Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local
+| | And   COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1
+| | And   COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1
+| | And   COP interface enable or disable | ${dut1} | ${dut1_if1} | enable
+| | And   COP interface enable or disable | ${dut2} | ${dut2_if2} | enable
+| | Then  Traffic should pass with no loss | ${duration} | ${rate}
+| | ...                                    | ${framesize} | 3-node-IPv6
+
+| TC07: Verify 78B ref-NDR at 2x 10.1Mpps - DUT IPv6 whitelist - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 78 Byte frames using single trial throughput test.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
+| | ${framesize}= | Set Variable | 78
+| | ${duration}= | Set Variable | 10
+| | ${rate}= | Set Variable | 10.1mpps
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And   Add all PCI devices to all DUTs
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv6 forwarding initialized in a 3-node circular topology
+| | And   Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local
+| | And   Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local
+| | And   COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1
+| | And   COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1
+| | And   COP interface enable or disable | ${dut1} | ${dut1_if1} | enable
+| | And   COP interface enable or disable | ${dut2} | ${dut2_if2} | enable
+| | Then  Traffic should pass with no loss | ${duration} | ${rate}
+| | ...                                    | ${framesize} | 3-node-IPv6
+
+| TC08: Verify 1518B ref-NDR at 2x 812.74kpps - DUT IPv6 whitelist - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 1518 Byte frames using single trial throughput test.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
+| | ${framesize}= | Set Variable | 1518
+| | ${duration}= | Set Variable | 10
+| | ${rate}= | Set Variable | 812743pps
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And   Add all PCI devices to all DUTs
+| | And   Add No Multi Seg to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv6 forwarding initialized in a 3-node circular topology
+| | And   Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local
+| | And   Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local
+| | And   COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1
+| | And   COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1
+| | And   COP interface enable or disable | ${dut1} | ${dut1_if1} | enable
+| | And   COP interface enable or disable | ${dut2} | ${dut2_if2} | enable
+| | Then  Traffic should pass with no loss | ${duration} | ${rate}
+| | ...                                    | ${framesize} | 3-node-IPv6
+
+| TC09: Verify 9000B ref-NDR at 2x 138.58kpps - DUT IPv6 whitelist - 4thread 4core 2rxq
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \
+| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify
+| | ... | ref-NDR for 9000 Byte frames using single trial throughput test.
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
+| | ${framesize}= | Set Variable | 9000
+| | ${duration}= | Set Variable | 10
+| | ${rate}= | Set Variable | 138580pps
+| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
+| | And   Add all PCI devices to all DUTs
+| | And   Apply startup configuration on all VPP DUTs
+| | When  IPv6 forwarding initialized in a 3-node circular topology
+| | And   Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local
+| | And   Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local
+| | And   COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1
+| | And   COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1
+| | And   COP interface enable or disable | ${dut1} | ${dut1_if1} | enable
+| | And   COP interface enable or disable | ${dut2} | ${dut2_if2} | enable
+| | Then  Traffic should pass with no loss | ${duration} | ${rate}
+| | ...                                    | ${framesize} | 3-node-IPv6