diff options
Diffstat (limited to 'tests/suites/honeycomb/1 - interface_management.robot')
| -rw-r--r-- | tests/suites/honeycomb/1 - interface_management.robot | 100 |
1 files changed, 100 insertions, 0 deletions
diff --git a/tests/suites/honeycomb/1 - interface_management.robot b/tests/suites/honeycomb/1 - interface_management.robot new file mode 100644 index 0000000000..50eaa4edeb --- /dev/null +++ b/tests/suites/honeycomb/1 - interface_management.robot @@ -0,0 +1,100 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Variables *** +# Node and interface to run tests on. +| ${node}= | ${nodes['DUT1']} +| ${interface}= | ${node['interfaces'].values()[0]['name']} +# Configuration which will be set and verified during tests. +| @{ipv4_address}= | 192.168.0.2 | 255.255.255.0 +| @{ipv4_neighbor}= | 192.168.0.3 | 08:00:27:c0:5d:37 +| &{ipv4_settings}= | enabled=${True} | forwarding=${True} | mtu=9000 +| @{ipv6_address}= | 10::10 | 64 +| @{ipv6_neighbor}= | 10::11 | 08:00:27:c0:5d:37 +| &{ipv6_settings}= | enabled=${True} | forwarding=${True} | mtu=9000 +| ... | dup-addr-detect-transmits=5 +| &{ethernet}= | mtu=9000 +| &{routing}= | vrf-id=27 +| &{vxlan_settings}= | src=10.0.1.20 | dst=10.0.3.20 | vni=1000 +| ... | encap-vrf-id=1000 + +*** Settings *** +| Resource | resources/libraries/robot/default.robot +| Resource | resources/libraries/robot/honeycomb/honeycomb.robot +| Resource | resources/libraries/robot/honeycomb/interfaces.robot +| Suite Setup | Run keywords | Setup all DUTs before test | AND +| ... | Setup Honeycomb service on DUTs | ${node} +| Documentation | *Honeycomb interface management test suite.* +| ... +| ... | Test suite uses the first interface of the first DUT node. + +*** Test Cases *** +| Honeycomb configures and reads interface state +| | [Documentation] | Check if Honeycomb API can modify the admin state of\ +| | ... | VPP interfaces. +| | [Tags] | honeycomb_sanity +| | Given Interface state is | ${node} | ${interface} | down +| | When Honeycomb sets interface state | ${node} | ${interface} | up +| | Then Interface state from Honeycomb should be +| | ... | ${node} | ${interface} | up +| | And Interface state from VAT should be | ${node} | ${interface} | up +| | When Honeycomb sets interface state | ${node} | ${interface} | down +| | Then Interface state from Honeycomb should be +| | ... | ${node} | ${interface} | down +| | And Interface state from VAT should be | ${node} | ${interface} | down + +| Honeycomb modifies interface configuration - ipv4 +| | [Documentation] | Check if Honeycomb API can configure interfaces for ipv4. +| | [Tags] | honeycomb_sanity +| | When Honeycomb sets interface ipv4 configuration +| | ... | ${node} | ${interface} | @{ipv4_address} | @{ipv4_neighbor} +| | ... | ${ipv4_settings} +| | Then IPv4 config from Honeycomb should be +| | ... | ${node} | ${interface} | @{ipv4_address} | @{ipv4_neighbor} +| | ... | ${ipv4_settings} +| | And IPv4 config from VAT should be +| | ... | ${node} | ${interface} | @{ipv4_address} + +| Honeycomb modifies interface configuration - ipv6 +| | [Documentation] | Check if Honeycomb API can configure interfaces for ipv6. +| | [Tags] | honeycomb_sanity +| | When Honeycomb sets interface ipv6 configuration +| | ... | ${node} | ${interface} | @{ipv6_address} | @{ipv6_neighbor} +| | ... | ${ipv6_settings} +| | Then IPv6 config from Honeycomb should be +| | ... | ${node} | ${interface} | @{ipv6_address} | @{ipv6_neighbor} +| | ... | ${ipv6_settings} +| | And IPv6 config from VAT should be +| | ... | ${node} | ${interface} | @{ipv6_address} + +| Honeycomb modifies interface configuration - ethernet,routing +| | [Documentation] | Check if Honeycomb API can configure interface ethernet\ +| | ... | and routing settings. +| | [Tags] | honeycomb_sanity +| | When Honeycomb sets interface ethernet and routing configuration +| | ... | ${node} | ${interface} | ${ethernet} | ${routing} +| | Then Interface ethernet and routing configuration from Honeycomb should be +| | ... | ${node} | ${interface} | ${ethernet} | ${routing} +| | And Interface ethernet and routing configuration from VAT should be +| | ... | ${node} | ${interface} | ${ethernet['mtu']} | ${routing['vrf-id']} + +| Honeycomb modifies interface configuration - VxLAN +| | [Documentation] | Check if Honeycomb API can configure interface VxLAN \ +| | ... | settings. +| | [Tags] | honeycomb_sanity +| | When Honeycomb sets interface VxLAN configuration +| | ... | ${node} | ${interface} | &{vxlan_settings} +| | Then VxLAN configuration from Honeycomb should be +| | ... | ${node} | ${interface} | &{vxlan_settings} +| | And VxLAN configuration from VAT should be +| | ... | ${node} | ${interface} | &{vxlan_settings} |