diff options
Diffstat (limited to 'tests/suites/performance/Long_IPv4_Cop_Intel-X520-DA2.robot')
| -rw-r--r-- | tests/suites/performance/Long_IPv4_Cop_Intel-X520-DA2.robot | 183 |
1 files changed, 111 insertions, 72 deletions
diff --git a/tests/suites/performance/Long_IPv4_Cop_Intel-X520-DA2.robot b/tests/suites/performance/Long_IPv4_Cop_Intel-X520-DA2.robot index 45245d92d9..fb7716b690 100644 --- a/tests/suites/performance/Long_IPv4_Cop_Intel-X520-DA2.robot +++ b/tests/suites/performance/Long_IPv4_Cop_Intel-X520-DA2.robot @@ -23,22 +23,36 @@ | Suite Teardown | 3-node Performance Suite Teardown | Test Setup | Setup all DUTs before test | Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs -| Documentation | *Throughput search suite (based on RFC2544).* +| Documentation | *RFC2544: Pkt throughput IPv4 whitelist test cases* | ... -| ... | Test suite uses 3-node topology TG - DUT1 - DUT2 - TG, with one link -| ... | between nodes. Traffic profile contain 2 L3 streams (1 stream per -| ... | direction). Packets contain Ethernet header, IPv4 header, -| ... | IP protocol=61 and random payload. Ethernet header MAC addresses are -| ... | matching MAC addresses of the TG node. COP (whitelist) is applied -| ... | on link between TG - DUT1 and DUT2 - TG. Additional ipv4 fib table with -| ... | index 1 is created and single entry added to permit all the -| ... | traffic (subnet /24). +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4 +| ... | routing, two static IPv4 /24 routes and IPv4 COP security whitelist +| ... | ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. +| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 253 flows per flow-group) with all packets +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static +| ... | payload. MAC addresses are matching MAC addresses of the TG node +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. *** Test Cases *** -| Find NDR by using RFC2544 binary search and 64B frames through IPv4 forwarding with COP in 3-node topology +| TC01: 64B NDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with non drop rate for 64B frames by using -| | ... | binary search with threshold 0.1Mpps. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 64 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${min_rate}= | Set Variable | 100000 @@ -62,11 +76,12 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR by using RFC2544 binary search and 64B frames through IPv4 forwarding with COP in 3-node topology +| TC02: 64B PDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with partial drop rate for 64B frames by using -| | ... | binary search with threshold 0.1Mpps. Loss acceptance is set to 0.5 -| | ... | percent of transmitted packets. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 64 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | PDR | | ${framesize}= | Set Variable | 64 | | ${min_rate}= | Set Variable | 100000 @@ -92,10 +107,12 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR by using RFC2544 binary search and 1518B frames through IPv4 forwarding with COP in 3-node topology +| TC03: 1518B NDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with non drop rate for 1518B frames by using -| | ... | binary search with threshold 10,000pps. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 @@ -119,11 +136,12 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR by using RFC2544 binary search and 1518B frames through IPv4 forwarding with COP in 3-node topology +| TC04: 1518B PDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with partial drop rate for 1518B frames by using -| | ... | binary search with threshold 10,000pps. Loss acceptance is set to 0.5 -| | ... | percent of transmitted packets. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | PDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 @@ -149,10 +167,12 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR by using RFC2544 binary search and 9000B frames through IPv4 forwarding with COP in 3-node topology +| TC05: 9000B NDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with non drop rate for 9000B frames by using -| | ... | binary search with threshold 5,000pps. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 @@ -175,11 +195,12 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR by using RFC2544 binary search and 9000B frames through IPv4 forwarding with COP in 3-node topology +| TC06: 9000B PDR binary search - DUT IPv4 whitelist - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with partial drop rate for 9000B frames by using -| | ... | binary search with threshold of 5,000pps. Loss acceptance is set to -| | ... | 0.5 percent of transmitted packets. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. | | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | PDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 @@ -204,10 +225,12 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 2 cores and rss 1 by using RFC2544 binary search and 64B frames through IPv4 forwarding with COP in 3-node topology +| TC07: 64B NDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with non drop rate for 64B frames by using -| | ... | binary search with threshold 0.1Mpps. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 64 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${min_rate}= | Set Variable | 100000 @@ -231,11 +254,12 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 2 cores and rss 1 by using RFC2544 binary search and 64B frames through IPv4 forwarding with COP in 3-node topology +| TC08: 64B PDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with partial drop rate for 64B frames by -| | ... | using binary search with threshold 0.1Mpps. Loss acceptance is set to -| | ... | 0.5 percent of transmitted packets. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 64 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 64 | | ${min_rate}= | Set Variable | 100000 @@ -261,10 +285,12 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 2 cores and rss 1 by using RFC2544 binary search and 1518B frames through IPv4 forwarding with COP in 3-node topology +| TC09: 1518B NDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with non drop rate for 1518B frames by -| | ... | using binary search with threshold 10,000pps. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 @@ -288,11 +314,12 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 2 cores and rss 1 by using RFC2544 binary search and 1518B frames through IPv4 forwarding with COP in 3-node topology +| TC10: 1518B PDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with partial drop rate for 1518B frames by -| | ... | using binary search with threshold 10,000pps. Loss acceptance is set -| | ... | to 0.5 percent of transmitted packets. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 @@ -318,10 +345,12 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 2 cores and rss 1 by using RFC2544 binary search and 9000B frames through IPv4 forwarding with COP in 3-node topology +| TC11: 9000B NDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with non drop rate for 9000B frames by -| | ... | using binary search with threshold 5,000pps. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 @@ -344,11 +373,12 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 2 cores and rss 1 by using RFC2544 binary search and 9000B frames through IPv4 forwarding with COP in 3-node topology +| TC12: 9000B PDR binary search - DUT IPv4 whitelist - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with partial drop rate for 9000B frames by -| | ... | using binary search with threshold 5,000pps. Loss acceptance is set -| | ... | to 0.5 percent of transmitted packets. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. | | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 @@ -373,10 +403,12 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 4 cores and rss 2 by using RFC2544 binary search and 64B frames through IPv4 forwarding with COP in 3-node topology +| TC13: 64B NDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with non drop rate for 64B -| | ... | frames by using binary search with threshold 0.1Mpps. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 64 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${min_rate}= | Set Variable | 100000 @@ -400,11 +432,12 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 4 cores and rss 2 by using RFC2544 binary search and 64B frames through IPv4 forwarding with COP in 3-node topology +| TC14: 64B PDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with partial drop rate for 64B -| | ... | frames by using binary search with threshold 0.1Mpps. Loss acceptance -| | ... | is set to 0.5 percent of transmitted packets. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 64 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 64 | | ${min_rate}= | Set Variable | 100000 @@ -430,10 +463,12 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 4 cores and rss 2 by using RFC2544 binary search and 1518B frames through IPv4 forwarding with COP in 3-node topology +| TC15: 1518B NDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with non drop rate for 1518B -| | ... | frames by using binary search with threshold 10,000pps. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 @@ -457,11 +492,12 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 4 cores and rss 2 by using RFC2544 binary search and 1518B frames through IPv4 forwarding with COP in 3-node topology +| TC16: 1518B PDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with partial drop rate for 1518B -| | ... | frames by using binary search with threshold 10,000pps. Loss -| | ... | acceptance is set to 0.5 percent of transmitted packets. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 @@ -487,10 +523,12 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 4 cores and rss 2 by using RFC2544 linear search and 9000B frames through IPv4 forwarding with COP in 3-node topology +| TC17: 9000B NDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with non drop rate for 9000B -| | ... | frames by using binary search with threshold 5,000pps. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 @@ -513,11 +551,12 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 4 cores and rss 2 by using RFC2544 linear search and 9000B frames through IPv4 forwarding with COP in 3-node topology +| TC18: 9000B PDR binary search - DUT IPv4 whitelist - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with partial drop rate for 9000B -| | ... | frames by using binary search with threshold 5,000pps. Loss -| | ... | acceptance is set to 0.5 percent of transmitted packets. +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. | | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 |