1 files changed, 0 insertions, 727 deletions
diff --git a/tests/suites/performance/Long_IPv4_iAcl_Intel-X520-DA2.robot b/tests/suites/performance/Long_IPv4_iAcl_Intel-X520-DA2.robot
deleted file mode 100644
index acf624514b..0000000000
--- a/tests/suites/performance/Long_IPv4_iAcl_Intel-X520-DA2.robot
+++ /dev/null
@@ -1,727 +0,0 @@
-# Copyright (c) 2016 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-#     http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Settings ***
-| Resource | resources/libraries/robot/performance.robot
-| Library | resources.libraries.python.Classify.Classify
-| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT1']} | WITH NAME | dut1_v4
-| Library | resources.libraries.python.IPv4Setup.Dut | ${nodes['DUT2']} | WITH NAME | dut2_v4
-| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PERFTEST_LONG
-| ...        | NIC_Intel-X520-DA2
-| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model
-| ... | L3 | Intel-X520-DA2
-| Suite Teardown | 3-node Performance Suite Teardown
-| Test Setup | Setup all DUTs before test
-| Test Teardown | Run Keywords | Remove startup configuration of VPP from all DUTs
-| ...           | AND          | Show vpp trace dump on all DUTs
-| Documentation | *RFC2544: Pkt throughput IPv4 iAcl whitelist test cases*
-| ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
-| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
-| ... | routing, two static IPv4 /24 routes and IPv4 iAcl security whitelist
-| ... | ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG.
-| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using either binary search or linear search
-| ... | algorithms with configured starting rate and final step that determines
-| ... | throughput measurement resolution. Test packets are generated by TG on
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
-| ... | (flow-group per direction, 253 flows per flow-group) with all packets
-| ... | containing Ethernet header, IPv4 header with IP protocol=61 and
-| ... | generated payload. MAC addresses are matching MAC addresses of the TG
-| ... | node interfaces.
-| ... | *[Ref] Applicable standard specifications:* RFC2544.
-
-*** Test Cases ***
-| TC01: 64B NDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR
-| | ... | for 64 Byte frames using binary search start at 10GE linerate,
-| | ... | step 100kpps.
-| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | SKIP_PATCH
-| | ${framesize}= | Set Variable | 64
-| | ${min_rate}= | Set Variable | 100000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_64B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-
-| TC02: 64B PDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR
-| | ... | for 64 Byte frames using binary search start at 10GE linerate,
-| | ... | step 100kpps, LT=0.5%.
-| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR
-| | ${framesize}= | Set Variable | 64
-| | ${min_rate}= | Set Variable | 100000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_64B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-| | ...                                       | ${glob_loss_acceptance}
-| | ...                                       | ${glob_loss_acceptance_type}
-
-| TC03: 1518B NDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR
-| | ... | for 1518 Byte frames using binary search start at 10GE linerate,
-| | ... | step 10kpps.
-| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | SKIP_PATCH
-| | ${framesize}= | Set Variable | 1518
-| | ${min_rate}= | Set Variable | 10000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1518B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-
-| TC04: 1518B PDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR
-| | ... | for 1518 Byte frames using binary search start at 10GE linerate,
-| | ... | step 10kpps, LT=0.5%.
-| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR
-| | ${framesize}= | Set Variable | 1518
-| | ${min_rate}= | Set Variable | 10000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1518B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-| | ...                                       | ${glob_loss_acceptance}
-| | ...                                       | ${glob_loss_acceptance_type}
-
-| TC05: 9000B NDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR
-| | ... | for 9000 Byte frames using binary search start at 10GE linerate,
-| | ... | step 5kpps.
-| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | SKIP_PATCH
-| | ${framesize}= | Set Variable | 9000
-| | ${min_rate}= | Set Variable | 5000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9000B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-
-| TC06: 9000B PDR binary search - DUT IPv4 iAcl whitelist - 1thread 1core 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR
-| | ... | for 9000 Byte frames using binary search start at 10GE linerate,
-| | ... | step 5kpps, LT=0.5%.
-| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR
-| | ${framesize}= | Set Variable | 9000
-| | ${min_rate}= | Set Variable | 5000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9000B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-| | ...                                       | ${glob_loss_acceptance}
-| | ...                                       | ${glob_loss_acceptance_type}
-
-| TC07: 64B NDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR
-| | ... | for 64 Byte frames using binary search start at 10GE linerate,
-| | ... | step 100kpps.
-| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | SKIP_PATCH
-| | ${framesize}= | Set Variable | 64
-| | ${min_rate}= | Set Variable | 100000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_64B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-
-| TC08: 64B PDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR
-| | ... | for 64 Byte frames using binary search start at 10GE linerate,
-| | ... | step 100kpps, LT=0.5%.
-| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR
-| | ${framesize}= | Set Variable | 64
-| | ${min_rate}= | Set Variable | 100000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_64B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-| | ...                                       | ${glob_loss_acceptance}
-| | ...                                       | ${glob_loss_acceptance_type}
-
-| TC09: 1518B NDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR
-| | ... | for 1518 Byte frames using binary search start at 10GE linerate,
-| | ... | step 10kpps.
-| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | SKIP_PATCH
-| | ${framesize}= | Set Variable | 1518
-| | ${min_rate}= | Set Variable | 10000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1518B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-
-| TC10: 1518B PDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR
-| | ... | for 1518 Byte frames using binary search start at 10GE linerate,
-| | ... | step 10kpps, LT=0.5%.
-| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | SKIP_PATCH
-| | ${framesize}= | Set Variable | 1518
-| | ${min_rate}= | Set Variable | 10000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1518B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-| | ...                                       | ${glob_loss_acceptance}
-| | ...                                       | ${glob_loss_acceptance_type}
-
-| TC11: 9000B NDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR
-| | ... | for 9000 Byte frames using binary search start at 10GE linerate,
-| | ... | step 5kpps.
-| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | SKIP_PATCH
-| | ${framesize}= | Set Variable | 9000
-| | ${min_rate}= | Set Variable | 5000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9000B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-
-| TC12: 9000B PDR binary search - DUT IPv4 iAcl whitelist - 2threads 2cores 1rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR
-| | ... | for 9000 Byte frames using binary search start at 10GE linerate,
-| | ... | step 5kpps, LT=0.5%.
-| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | SKIP_PATCH
-| | ${framesize}= | Set Variable | 9000
-| | ${min_rate}= | Set Variable | 5000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9000B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-| | ...                                       | ${glob_loss_acceptance}
-| | ...                                       | ${glob_loss_acceptance_type}
-
-| TC13: 64B NDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR
-| | ... | for 64 Byte frames using binary search start at 10GE linerate,
-| | ... | step 100kpps.
-| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | SKIP_PATCH
-| | ${framesize}= | Set Variable | 64
-| | ${min_rate}= | Set Variable | 100000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_64B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-
-| TC14: 64B PDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR
-| | ... | for 64 Byte frames using binary search start at 10GE linerate,
-| | ... | step 100kpps, LT=0.5%.
-| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR
-| | ${framesize}= | Set Variable | 64
-| | ${min_rate}= | Set Variable | 100000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_64B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-| | ...                                       | ${glob_loss_acceptance}
-| | ...                                       | ${glob_loss_acceptance_type}
-
-| TC15: 1518B NDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR
-| | ... | for 1518 Byte frames using binary search start at 10GE linerate,
-| | ... | step 10kpps.
-| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | SKIP_PATCH
-| | ${framesize}= | Set Variable | 1518
-| | ${min_rate}= | Set Variable | 10000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1518B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-
-| TC16: 1518B PDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR
-| | ... | for 1518 Byte frames using binary search start at 10GE linerate,
-| | ... | step 10kpps, LT=0.5%.
-| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | SKIP_PATCH
-| | ${framesize}= | Set Variable | 1518
-| | ${min_rate}= | Set Variable | 10000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1518B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Add No Multi Seg to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-| | ...                                       | ${glob_loss_acceptance}
-| | ...                                       | ${glob_loss_acceptance_type}
-
-| TC17: 9000B NDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR
-| | ... | for 9000 Byte frames using binary search start at 10GE linerate,
-| | ... | step 5kpps.
-| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | SKIP_PATCH
-| | ${framesize}= | Set Variable | 9000
-| | ${min_rate}= | Set Variable | 5000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9000B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-
-| TC18: 9000B PDR binary search - DUT IPv4 iAcl whitelist - 4threads 4cores 2rxq
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \
-| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR
-| | ... | for 9000 Byte frames using binary search start at 10GE linerate,
-| | ... | step 5kpps, LT=0.5%.
-| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | SKIP_PATCH
-| | ${framesize}= | Set Variable | 9000
-| | ${min_rate}= | Set Variable | 5000
-| | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9000B}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs
-| | And   Add all PCI devices to all DUTs
-| | And   Apply startup configuration on all VPP DUTs
-| | When  IPv4 forwarding initialized in a 3-node circular topology
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut1} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 20.20.20.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut1} | ${dut1_if1} | ip4 | ${table_idx}
-| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
-| | ... | ${dut2} | ip4 | dst
-| | And Vpp Configures Classify Session L3
-| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
-| | ... | ip4 | dst | 10.10.10.2
-| | And Vpp Enable Input Acl Interface
-| | ... | ${dut2} | ${dut2_if2} | ip4 | ${table_idx}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ...                                       | ${binary_max} | 3-node-IPv4
-| | ...                                       | ${min_rate} | ${max_rate}
-| | ...                                       | ${threshold}
-| | ...                                       | ${glob_loss_acceptance}
-| | ...                                       | ${glob_loss_acceptance_type}