diff options
Diffstat (limited to 'tests/suites/softwire/lightweight_4over6.robot')
| -rw-r--r-- | tests/suites/softwire/lightweight_4over6.robot | 200 |
1 files changed, 0 insertions, 200 deletions
diff --git a/tests/suites/softwire/lightweight_4over6.robot b/tests/suites/softwire/lightweight_4over6.robot deleted file mode 100644 index 68eea42d8e..0000000000 --- a/tests/suites/softwire/lightweight_4over6.robot +++ /dev/null @@ -1,200 +0,0 @@ -# Copyright (c) 2016 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/default.robot -| Resource | resources/libraries/robot/testing_path.robot -| Resource | resources/libraries/robot/ipv4.robot -| Resource | resources/libraries/robot/ipv6.robot -| Resource | resources/libraries/robot/map.robot -| Library | resources.libraries.python.Trace -| Force Tags | HW_ENV | VM_ENV | 3_NODE_DOUBLE_LINK_TOPO -| Test Setup | Run Keywords | Setup all DUTs before test -| ... | AND | Setup all TGs before traffic script -| Test Teardown | Show Packet Trace on All DUTs | ${nodes} -| Documentation | *Lightweight 4 over 6 test cases* -| ... -| ... | LW4o6 is a subset of MAP-E, with per-subscriber rules. It uses the -| ... | same tunneling mechanism and configuration as MAP-E. It does not use -| ... | embedded address bits. -| ... -| ... | *[Top] Network Topologies:* TG=DUT1 2-node topology with two links -| ... | between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP on TG_if1-DUT, -| ... | Eth-IPv6-IPv4-UDP on TG_if2_DUT. -| ... | *[Cfg] DUT configuration:* DUT1 is configured as lwAFTR. -| ... | *[Ver] TG verification:* Test UDP ICMP Echo Request in IPv4 are -| ... | sent to lwAFTR and are verified by TG for correctness their -| ... | encapsulation in IPv6 src-addr, dst-addr and MAC addresses. -| ... | *[Ref] Applicable standard specifications:* RFC7596 RFC7597. - -*** Variables *** -| ${dut_ip4}= | 10.0.0.1 -| ${dut_ip6}= | 2001:0::1 -| ${ipv4_prefix_len}= | 24 -| ${ipv6_prefix_len}= | 64 - -| ${lw_ipv4_pfx}= | 20.0.0.1/32 -| ${lw_ipv6_pfx}= | 2001:1::/64 -| ${lw_ipv6_src}= | 2001:1::1 -| ${lw_psid_length}= | ${8} -| ${lw_psid_offset}= | ${6} -| ${lw_rule_psid}= | ${52} -| ${lw_rule_ipv6_dst}= | 2001:1::2 -| ${lw_rule_2_psid}= | ${22} -| ${lw_rule_2_ipv6_dst}= | 2001:1::3 -| ${test_ipv4_inside}= | 20.0.0.1 -| ${test_ipv4_outside}= | 10.0.0.100 -# test_port depends on psid, length, offset -| ${test_port}= | ${1232} -| ${test_icmp_id}= | ${1232} -| ${test_2_port}= | ${6232} - -*** Test Cases *** -| TC01: Encapsulate IPv4 into IPv6. IPv6 dst depends on IPv4 and UDP destination -| | [Documentation] -| | ... | [Top] TG=DUT1. -| | ... | [Enc] Eth-IPv4-UDP on TG_if1-DUT, Eth-IPv6-IPv4-UDP on TG_if2_DUT. -| | ... | [Cfg] On DUT1 configure Map domain and Map rule. -| | ... | [Ver] Make TG send non-encapsulated UDP to DUT; verify TG received -| | ... | IPv4oIPv6 encapsulated packet is correct. -| | ... | [Ref] RFC7596 RFC7597 -| | ... -| | Given Path for 2-node testing is set -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['TG']} -| | And Interfaces in 2-node path are up -| | And IP addresses are set on interfaces -| | ... | ${dut_node} | ${dut_to_tg_if1} | ${dut_ip4} | ${ipv4_prefix_len} -| | ... | ${dut_node} | ${dut_to_tg_if2} | ${dut_ip6} | ${ipv6_prefix_len} -| | And Add IP Neighbor -| | ... | ${dut_node} | ${dut_to_tg_if2} | ${lw_rule_ipv6_dst} -| | ... | ${tg_to_dut_if2_mac} -| | ${domain_index}= -| | ... | When Map Add Domain -| | ... | ${dut_node} | ${lw_ipv4_pfx} | ${lw_ipv6_pfx} -| | ... | ${lw_ipv6_src} | 0 | ${lw_psid_offset} -| | ... | ${lw_psid_length} -| | And Map Add Rule -| | ... | ${dut_node} | ${domain_index} | ${lw_rule_psid} -| | ... | ${lw_rule_ipv6_dst} -| | Then Send IPv4 UDP and check headers for lightweight 4over6 -| | ... | ${tg_node} | ${tg_to_dut_if1} | ${tg_to_dut_if2} -| | ... | ${dut_to_tg_if1_mac} | ${test_ipv4_inside} | ${test_ipv4_outside} -| | ... | ${test_port} | ${tg_to_dut_if2_mac} | ${dut_to_tg_if2_mac} -| | ... | ${lw_rule_ipv6_dst} | ${lw_ipv6_src} - -TC02: Encapsulate IPv4 ICMP into IPv6. IPv6 dst depends on IPv4 addr and ICMP ID -| | [Documentation] -| | ... | [Top] TG=DUT1. -| | ... | [Enc] Eth-IPv4-ICMP(type 0 and 8) on TG_if1-DUT, Eth-IPv6-IPv4-ICMP -| | ... | on TG_if2_DUT. -| | ... | [Cfg] On DUT1 configure Map domain and Map rule. -| | ... | [Ver] Make TG send non-encapsulated ICMP to DUT; verify TG received -| | ... | IPv4oIPv6 encapsulated packet is correct. Checks IPv6 -| | ... | destination based on ICMP Identifier field. -| | ... | [Ref] RFC7596 section 8.1 -| | ... -| | Given Path for 2-node testing is set -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['TG']} -| | And Interfaces in 2-node path are up -| | And IP addresses are set on interfaces -| | ... | ${dut_node} | ${dut_to_tg_if1} | ${dut_ip4} | ${ipv4_prefix_len} -| | ... | ${dut_node} | ${dut_to_tg_if2} | ${dut_ip6} | ${ipv6_prefix_len} -| | And Add IP Neighbor -| | ... | ${dut_node} | ${dut_to_tg_if2} | ${lw_rule_ipv6_dst} -| | ... | ${tg_to_dut_if2_mac} -| | ${domain_index}= -| | ... | When Map Add Domain -| | ... | ${dut_node} | ${lw_ipv4_pfx} | ${lw_ipv6_pfx} -| | ... | ${lw_ipv6_src} | 0 | ${lw_psid_offset} -| | ... | ${lw_psid_length} -| | And Map Add Rule -| | ... | ${dut_node} | ${domain_index} | ${lw_rule_psid} -| | ... | ${lw_rule_ipv6_dst} -| | Then Send IPv4 ICMP and check headers for lightweight 4over6 -| | ... | ${tg_node} | ${tg_to_dut_if1} | ${tg_to_dut_if2} -| | ... | ${dut_to_tg_if1_mac} | ${test_ipv4_inside} | ${test_ipv4_outside} -| | ... | ${test_icmp_id} | ${tg_to_dut_if2_mac} | ${dut_to_tg_if2_mac} -| | ... | ${lw_rule_ipv6_dst} | ${lw_ipv6_src} - -TC03: Decapsulate IPv4 UDP from IPv6. -| | [Documentation] -| | ... | [Top] TG=DUT1. -| | ... | [Enc] Eth-IPv6-IPv4-UDP on TG_if2_DUT, Eth-IPv4-UDP on TG_if1-DUT. -| | ... | [Cfg] On DUT1 configure Map domain and Map rule. -| | ... | [Ver] Make TG send encapsulated UDP to DUT; verify TG received -| | ... | IPv4 non-encapsulated packet is correct. -| | ... | [Ref] RFC7596 RFC7597 -| | ... -| | Given Path for 2-node testing is set -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['TG']} -| | And Interfaces in 2-node path are up -| | And IP addresses are set on interfaces -| | ... | ${dut_node} | ${dut_to_tg_if1} | ${dut_ip4} | ${ipv4_prefix_len} -| | ... | ${dut_node} | ${dut_to_tg_if2} | ${dut_ip6} | ${ipv6_prefix_len} -| | And Add Arp on DUT -| | ... | ${dut_node} | ${dut_to_tg_if1} -| | ... | ${test_ipv4_outside} -| | ... | ${tg_to_dut_if1_mac} -| | ${domain_index}= -| | ... | When Map Add Domain -| | ... | ${dut_node} | ${lw_ipv4_pfx} | ${lw_ipv6_pfx} -| | ... | ${lw_ipv6_src} | 0 | ${lw_psid_offset} -| | ... | ${lw_psid_length} -| | And Map Add Rule -| | ... | ${dut_node} | ${domain_index} | ${lw_rule_psid} -| | ... | ${lw_rule_ipv6_dst} -| | Then Send IPv4 UDP in IPv6 and check headers for lightweight 4over6 -| | ... | ${tg_node} | ${tg_to_dut_if2} | ${tg_to_dut_if1} -| | ... | ${dut_to_tg_if2_mac} | ${tg_to_dut_if2_mac} -| | ... | ${lw_ipv6_src} | ${lw_rule_ipv6_dst} -| | ... | ${test_ipv4_outside} | ${test_ipv4_inside} | ${test_port} -| | ... | ${tg_to_dut_if1_mac} | ${dut_to_tg_if1_mac} - -TC04: Hairpinning of traffic between two lwB4 -| | [Documentation] -| | ... | [Top] DUT1-TG. -| | ... | [Enc] Eth-IPv6-IPv4-UDP on TG_if2_DUT, Eth-IPv6-IPv4-UDP on TG_if2_DUT. -| | ... | [Cfg] On DUT1 configure Map domain and two Map rules. -| | ... | [Ver] Make TG send encapsulated UDP to DUT; verify TG received -| | ... | encapsulated packet is correct. -| | ... | [Ref] RFC7596 RFC7597 -| | ... -| | Given Path for 2-node testing is set -| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['TG']} -| | And Interfaces in 2-node path are up -| | And IP addresses are set on interfaces -| | ... | ${dut_node} | ${dut_to_tg_if1} | ${dut_ip4} | ${ipv4_prefix_len} -| | ... | ${dut_node} | ${dut_to_tg_if2} | ${dut_ip6} | ${ipv6_prefix_len} -| | And Add IP Neighbor -| | ... | ${dut_node} | ${dut_to_tg_if2} | ${lw_rule_2_ipv6_dst} -| | ... | ${tg_to_dut_if2_mac} -| | ${domain_index}= -| | ... | When Map Add Domain -| | ... | ${dut_node} | ${lw_ipv4_pfx} | ${lw_ipv6_pfx} -| | ... | ${lw_ipv6_src} | 0 | ${lw_psid_offset} -| | ... | ${lw_psid_length} -| | And Map Add Rule -| | ... | ${dut_node} | ${domain_index} | ${lw_rule_psid} -| | ... | ${lw_rule_ipv6_dst} -| | And Map Add Rule -| | ... | ${dut_node} | ${domain_index} | ${lw_rule_2_psid} -| | ... | ${lw_rule_2_ipv6_dst} -| | Then Send IPv4 UDP in IPv6 and check headers for lightweight hairpinning -| | ... | ${tg_node} | ${tg_to_dut_if2} | ${tg_to_dut_if2} -| | ... | ${dut_to_tg_if2_mac} -| | ... | ${lw_ipv6_src} | ${lw_rule_ipv6_dst} -| | ... | ${test_ipv4_inside} | ${test_ipv4_inside} -| | ... | ${test_2_port} | ${test_port} -| | ... | ${tg_to_dut_if2_mac} | ${dut_to_tg_if2_mac} -| | ... | ${lw_rule_2_ipv6_dst} | ${lw_ipv6_src} |