diff options
Diffstat (limited to 'tests/suites/vlan')
| -rw-r--r-- | tests/suites/vlan/qinq_l2_xconnect.robot | 71 | ||||
| -rw-r--r-- | tests/suites/vlan/vlan_tag_translate_l2_xconnect_ipv4.robot | 453 |
2 files changed, 524 insertions, 0 deletions
diff --git a/tests/suites/vlan/qinq_l2_xconnect.robot b/tests/suites/vlan/qinq_l2_xconnect.robot new file mode 100644 index 0000000000..35fdcde6ca --- /dev/null +++ b/tests/suites/vlan/qinq_l2_xconnect.robot @@ -0,0 +1,71 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/default.robot +| Resource | resources/libraries/robot/testing_path.robot +| Resource | resources/libraries/robot/tagging.robot +| Resource | resources/libraries/robot/l2_traffic.robot +| Library | resources.libraries.python.Trace +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | HW_ENV | VM_ENV +| Test Setup | Setup all DUTs before test +| Suite Setup | Setup all TGs before traffic script +| Test Teardown | Run Keywords | Show Packet Trace on All DUTs | ${nodes} +| ... | AND | Show vpp trace dump on all DUTs +| Documentation | *L2 cross-connect with QinQ test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology with +| ... | single links between nodes. +| ... | *[Enc] Packet encapsulations:* Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, +| ... | Eth-IPv4-ICMPv4 on TG-DUTn for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 +| ... | cross-connect (L2XC) switching with 802.1ad QinQ VLAN tag push and pop. +| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets are +| ... | sent in both directions by TG on links to DUT1 and DUT2; on receive TG +| ... | verifies packets for correctness and their IPv4 src-addr, dst-addr and +| ... | MAC addresses. +| ... | *[Ref] Applicable standard specifications:* IEEE 802.1ad. + +*** Variables *** +| ${subid}= | 10 +| ${outer_vlan_id}= | 100 +| ${inner_vlan_id}= | 200 +| ${type_subif}= | two_tags +| ${tag_rewrite_method}= | pop-2 + +*** Test Cases *** +| TC01: DUT1 and DUT2 with L2XC and two VLAN push-pop switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv4-ICMPv4 on \ +| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 and DUT2 +| | ... | configure L2 cross-connect (L2XC), each with one interface to TG +| | ... | and one Ethernet interface towards the other DUT; each DUT +| | ... | pushes two VLAN tags on packets received from local TG, and +| | ... | popping two VLAN tags on packets transmitted to local TG. [Ver] +| | ... | Make TG send ICMPv4 Echo Req in both directions between two of +| | ... | its interfaces to be switched by DUT1 and DUT2; verify all +| | ... | packets are received. [Ref] IEEE 802.1ad. +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | When VLAN subinterfaces initialized on 3-node topology +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${dut2_node} | ${dut2_to_dut1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And L2 tag rewrite method setup on interfaces +| | ... | ${dut1_node} | ${subif_index_1} | ${dut2_node} | ${subif_index_2} +| | ... | ${tag_rewrite_method} +| | And Interfaces and VLAN sub-interfaces inter-connected using L2-xconnect +| | ... | ${dut1_node} | ${dut1_to_tg} | ${subif_index_1} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${subif_index_2} +| | Then Send and receive ICMP Packet +| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} diff --git a/tests/suites/vlan/vlan_tag_translate_l2_xconnect_ipv4.robot b/tests/suites/vlan/vlan_tag_translate_l2_xconnect_ipv4.robot new file mode 100644 index 0000000000..f1a954f4d0 --- /dev/null +++ b/tests/suites/vlan/vlan_tag_translate_l2_xconnect_ipv4.robot @@ -0,0 +1,453 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/default.robot +| Resource | resources/libraries/robot/testing_path.robot +| Resource | resources/libraries/robot/tagging.robot +| Resource | resources/libraries/robot/l2_traffic.robot +| Library | resources.libraries.python.Trace +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | HW_ENV | VM_ENV +| Test Setup | Setup all DUTs before test +| Suite Setup | Setup all TGs before traffic script +| Test Teardown | Run Keywords | Show Packet Trace on All DUTs | ${nodes} +| ... | AND | Show vpp trace dump on all DUTs +| Documentation | *L2 cross-connect with VLAN tag rewrite test cases - IPv4* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet encapsulations:* Eth-dot1q-IPv4-ICMPv4 or +| ... | Eth-dot1ad-IPv4-ICMPv4 on TG-DUT1 and DUT1-DUT2, Eth-IPv4-ICMPv4 +| ... | on TG-DUT2 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 cross-connect +| ... | (L2XC) switching between VLAN sub-interface with VLAN tag rewrite +| ... | translate-1-1 method of interface towards TG and interface towards DUT2. +| ... | DUT2 is configured configured with L2 cross-connect (L2XC) switching +| ... | between VLAN sub-interface with VLAN tag rewrite pop-1 method +| ... | of interface towards DUT1 and interface towards TG. +| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets are +| ... | sent from TG on link to DUT1 and received in TG on link form DUT2; +| ... | on receive TG verifies packets for correctness and their IPv4 src-addr, +| ... | dst-addr and MAC addresses. +| ... | *[Ref] Applicable standard specifications:* IEEE 802.1q, IEEE 802.1ad. + +*** Variables *** +| ${subid}= | 10 +| ${outer_vlan_id1}= | 110 +| ${outer_vlan_id2}= | 120 +| ${outer_vlan_wrong}= | 150 +| ${inner_vlan_id1}= | 210 +| ${inner_vlan_id2}= | 220 +| ${inner_vlan_wrong}= | 250 + +*** Test Cases *** +| TC01: DUT1 and DUT2 with L2XC and VLAN translate-1-1 (DUT1) switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1 and \ +| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 +| | ... | cross-connect (L2XC) with one interface to DUT2 and one VLAN +| | ... | sub-interface towards TG with VLAN tag rewrite translate-1-1 method; +| | ... | on DUT2 configure L2 cross-connect (L2XC) with one interface to TG +| | ... | and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 +| | ... | method. [Ver] Make TG send ICMPv4 Echo Req tagged with one Dot1q tag +| | ... | from one of its interfaces to another one via DUT1 and DUT2; verify +| | ... | that packet is received. [Ref] IEEE 802.1q +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | ${vlan1_name} | ${vlan1_index}= | When Vlan Subinterface Created +| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} +| | ${vlan2_name} | ${vlan2_index}= | And Vlan Subinterface Created +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_id2} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-1 +| | And Interfaces and VLAN sub-interfaces inter-connected using L2-xconnect +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Send and receive ICMP Packet +| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | encaps=Dot1q +| | ... | vlan1=${outer_vlan_id1} + +| TC02: DUT1 and DUT2 with L2XC and VLAN translate-1-1 with wrong tag used (DUT1) switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1 and \ +| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 +| | ... | cross-connect (L2XC) with one VLAN tagged sub-interface to DUT2 and +| | ... | one VLAN sub-interface towards TG with VLAN tag rewrite +| | ... | (translate-1-1) on sub-interface to DUT2; on DUT2 configure L2XC with +| | ... | one interface to TG and one VLAN sub-interface towards DUT1 with VLAN +| | ... | tag pop-1. [Ver] Make TG send ICMPv4 Echo Req tagged with one dot1q +| | ... | tag from one of its interfaces to another one via DUT1 and DUT2; +| | ... | verify that packet is not received. [Ref] IEEE 802.1q +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | ${vlan1_name} | ${vlan1_index}= | When Vlan Subinterface Created +| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} +| | ${vlan2_name} | ${vlan2_index}= | And Vlan Subinterface Created +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_wrong} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-1 +| | And Interfaces and VLAN sub-interfaces inter-connected using L2-xconnect +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Run Keyword And Expect Error | ICMP echo Rx timeout +| | ... | Send and receive ICMP Packet | ${tg_node} | ${tg_to_dut1} +| | ... | ${tg_to_dut2} | encaps=Dot1q | vlan1=${outer_vlan_id1} + +| TC03: DUT1 and DUT2 with L2XC and VLAN translate-1-2 (DUT1) switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1, \ +| | ... | Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. +| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to +| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite +| | ... | translate-1-2 method; on DUT2 configure L2 cross-connect (L2XC) with +| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with +| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv4 Echo Req +| | ... | tagged with one Dot1q tag from one of its interfaces to another one +| | ... | via DUT1 and DUT2; verify that packet is received. +| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | ${vlan1_name} | ${vlan1_index}= | When Vlan Subinterface Created +| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} +| | ${vlan2_name} | ${vlan2_index}= | And Tagged Subinterface Created +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} +| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} +| | ... | type_subif=two_tags dot1ad +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} +| | ... | tag1_id=${outer_vlan_id2} | tag2_id=${inner_vlan_id2} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-2 +| | And Interfaces and VLAN sub-interfaces inter-connected using L2-xconnect +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Send and receive ICMP Packet +| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | encaps=Dot1q +| | ... | vlan1=${outer_vlan_id1} + +| TC04: DUT1 and DUT2 with L2XC and VLAN translate-1-2 with wrong inner tag used (DUT1) switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1, \ +| | ... | Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. +| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to +| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite +| | ... | translate-1-2 method to set inner tag different from inner tag set on +| | ... | Dot1ad sub-interface of DUT2; on DUT2 configure L2 cross-connect with +| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with +| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv4 Echo Req +| | ... | tagged with one Dot1q tag from one of its interfaces to another one +| | ... | via DUT1 and DUT2; verify that packet is not received. +| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | ${vlan1_name} | ${vlan1_index}= | When Vlan Subinterface Created +| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} +| | ${vlan2_name} | ${vlan2_index}= | And Tagged Subinterface Created +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} +| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} +| | ... | type_subif=two_tags dot1ad +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} +| | ... | tag1_id=${outer_vlan_id2} | tag2_id=${inner_vlan_wrong} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-2 +| | And Interfaces and VLAN sub-interfaces inter-connected using L2-xconnect +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Run Keyword And Expect Error | ICMP echo Rx timeout +| | ... | Send and receive ICMP Packet | ${tg_node} | ${tg_to_dut1} +| | ... | ${tg_to_dut2} | encaps=Dot1q | vlan1=${outer_vlan_id1} + +| TC05: DUT1 and DUT2 with L2XC and VLAN translate-1-2 with wrong outer tag used (DUT1) switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1, \ +| | ... | Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. +| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to +| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite +| | ... | translate-1-2 method to set outer tag different from outer tag set on +| | ... | Dot1ad sub-interface of DUT2; on DUT2 configure L2 cross-connect with +| | ... | one interface to TG and one Dot1ad sub-interface towards DUT1 with +| | ... | VLAN tag rewrite pop-2 method. [Ver] Make TG send ICMPv4 Echo Req +| | ... | tagged with one Dot1q tag from one of its interfaces to another one +| | ... | via DUT1 and DUT2; verify that packet is not received. +| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | ${vlan1_name} | ${vlan1_index}= | When Vlan Subinterface Created +| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} +| | ${vlan2_name} | ${vlan2_index}= | And Tagged Subinterface Created +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} +| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} +| | ... | type_subif=two_tags dot1ad +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} +| | ... | tag1_id=${outer_vlan_wrong} | tag2_id=${inner_vlan_id2} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-2 +| | And Interfaces and VLAN sub-interfaces inter-connected using L2-xconnect +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Run Keyword And Expect Error | ICMP echo Rx timeout +| | ... | Send and receive ICMP Packet | ${tg_node} | ${tg_to_dut1} +| | ... | ${tg_to_dut2} | encaps=Dot1q | vlan1=${outer_vlan_id1} + +| TC06: DUT1 and DUT2 with L2XC and VLAN translate-1-2 with wrong outer and inner tag used (DUT1) switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1, \ +| | ... | Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. +| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to +| | ... | DUT2 and one VLAN sub-interface towards TG with VLAN tag rewrite +| | ... | translate-1-2 method to set outer and inner tags different from tags +| | ... | set on Dot1ad sub-interface of DUT2; on DUT2 configure L2 +| | ... | cross-connect with one interface to TG and one Dot1ad sub-interface +| | ... | towards DUT1 with VLAN tag rewrite pop-2 method. [Ver] Make TG send +| | ... | ICMPv4 Echo Req tagged with one Dot1q tag from one of its interfaces +| | ... | to another one via DUT1 and DUT2; verify that packet is not received. +| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | ${vlan1_name} | ${vlan1_index}= | When Vlan Subinterface Created +| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} +| | ${vlan2_name} | ${vlan2_index}= | And Tagged Subinterface Created +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} +| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} +| | ... | type_subif=two_tags dot1ad +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-1-2 | push_dot1q=${False} +| | ... | tag1_id=${outer_vlan_wrong} | tag2_id=${inner_vlan_wrong} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-2 +| | And Interfaces and VLAN sub-interfaces inter-connected using L2-xconnect +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Run Keyword And Expect Error | ICMP echo Rx timeout +| | ... | Send and receive ICMP Packet | ${tg_node} | ${tg_to_dut1} +| | ... | ${tg_to_dut2} | encaps=Dot1q | vlan1=${outer_vlan_id1} + +| TC07: DUT1 and DUT2 with L2XC and VLAN translate-2-1 (DUT1) switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv4-ICMPv4 on TG-DUT1, \ +| | ... | Eth-dot1q-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. +| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to +| | ... | DUT2 and one Dot1ad sub-interface towards TG with VLAN tag rewrite +| | ... | translate-2-1 method; on DUT2 configure L2 cross-connect (L2XC) with +| | ... | one interface to TG and one VLAN sub-interface towards DUT1 with +| | ... | VLAN tag rewrite pop-1 method. [Ver] Make TG send ICMPv4 Echo Req +| | ... | tagged with Dot1ad tags from one of its interfaces to another one +| | ... | via DUT1 and DUT2; verify that packet is received. +| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | ${vlan1_name} | ${vlan1_index}= | When Tagged Subinterface Created +| | ... | ${dut1_node} | ${dut1_to_tg} | ${subid} +| | ... | outer_vlan_id=${outer_vlan_id1} | inner_vlan_id=${inner_vlan_id1} +| | ... | type_subif=two_tags dot1ad +| | ${vlan2_name} | ${vlan2_index}= | And Vlan Subinterface Created +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-2-1 | tag1_id=${outer_vlan_id2} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-1 +| | And Interfaces and VLAN sub-interfaces inter-connected using L2-xconnect +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Send and receive ICMP Packet +| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | encaps=Dot1ad +| | ... | vlan1=${outer_vlan_id1} | vlan2=${inner_vlan_id1} + +| TC08: DUT1 and DUT2 with L2XC and VLAN translate-2-1 with wrong tag used (DUT1) switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv4-ICMPv4 on TG-DUT1, \ +| | ... | Eth-dot1q-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. +| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC) with one interface to +| | ... | DUT2 and one Dot1ad sub-interface towards TG with VLAN tag rewrite +| | ... | translate-2-1 method to set tag different from tag set on VLAN +| | ... | sub-interface of DUT2; on DUT2 configure L2 cross-connect (L2XC) with +| | ... | one interface to TG and one VLAN sub-interface towards DUT1 with +| | ... | VLAN tag rewrite pop-1 method. [Ver] Make TG send ICMPv4 Echo Req +| | ... | tagged with Dot1ad tags from one of its interfaces to another one +| | ... | via DUT1 and DUT2; verify that packet is not received. +| | ... | [Ref] IEEE 802.1q, IEEE 802.1ad +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | ${vlan1_name} | ${vlan1_index}= | When Tagged Subinterface Created +| | ... | ${dut1_node} | ${dut1_to_tg} | ${subid} +| | ... | outer_vlan_id=${outer_vlan_id1} | inner_vlan_id=${inner_vlan_id1} +| | ... | type_subif=two_tags dot1ad +| | ${vlan2_name} | ${vlan2_index}= | And Vlan Subinterface Created +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-2-1 | tag1_id=${outer_vlan_wrong} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-1 +| | And Interfaces and VLAN sub-interfaces inter-connected using L2-xconnect +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Run Keyword And Expect Error | ICMP echo Rx timeout +| | ... | Send and receive ICMP Packet | ${tg_node} | ${tg_to_dut1} +| | ... | ${tg_to_dut2} | encaps=Dot1ad | vlan1=${outer_vlan_id1} +| | ... | vlan2=${inner_vlan_id1} + +| TC09: DUT1 and DUT2 with L2XC and VLAN translate-2-2 switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv4-ICMPv4 on TG-DUT1 and \ +| | ... | on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 +| | ... | cross-connect (L2XC) with one interface to DUT2 and one Dot1ad +| | ... | sub-interface towards TG with VLAN tag rewrite translate-2-2 method; +| | ... | on DUT2 configure L2 cross-connect (L2XC) with one interface to TG and +| | ... | one Dot1ad sub-interface towards DUT1 with VLAN tag rewrite pop-1 +| | ... | tagged with Dot1ad tags from one of its interfaces to another one +| | ... | method. [Ver] Make TG send ICMPv4 Echo Req via DUT1 and DUT2; verify +| | ... | that packet is received. [Ref] IEEE 802.1ad +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | ${vlan1_name} | ${vlan1_index}= | When Tagged Subinterface Created +| | ... | ${dut1_node} | ${dut1_to_tg} | ${subid} +| | ... | outer_vlan_id=${outer_vlan_id1} | inner_vlan_id=${inner_vlan_id1} +| | ... | type_subif=two_tags dot1ad +| | ${vlan2_name} | ${vlan2_index}= | And Tagged Subinterface Created +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} +| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} +| | ... | type_subif=two_tags dot1ad +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-2-2 | push_dot1q=${False} +| | ... | tag1_id=${outer_vlan_id2} | tag2_id=${inner_vlan_id2} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-2 +| | And Interfaces and VLAN sub-interfaces inter-connected using L2-xconnect +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Send and receive ICMP Packet +| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | encaps=Dot1ad +| | ... | vlan1=${outer_vlan_id1} | vlan2=${inner_vlan_id1} + +| TC10: DUT1 and DUT2 with L2XC and VLAN translate-2-2 with wrong inner tag used (DUT1) switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv4-ICMPv4 on TG-DUT1 and \ +| | ... | on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 +| | ... | cross-connect (L2XC) with one interface to DUT2 and one Dot1ad +| | ... | sub-interface towards TG with VLAN tag rewrite translate-2-2 method to +| | ... | set inner tag different from inner tag set on Dot1ad sub-interface of +| | ... | DUT2; on DUT2 configure L2 cross-connect (L2XC) with one interface to +| | ... | TG and one Dot1ad sub-interface towards DUT1 with VLAN tag rewrite +| | ... | pop-1 tagged with Dot1ad tags from one of its interfaces to another one +| | ... | method. [Ver] Make TG send ICMPv4 Echo Req via DUT1 and DUT2; verify +| | ... | that packet is not received. [Ref] IEEE 802.1ad +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | ${vlan1_name} | ${vlan1_index}= | When Tagged Subinterface Created +| | ... | ${dut1_node} | ${dut1_to_tg} | ${subid} +| | ... | outer_vlan_id=${outer_vlan_id1} | inner_vlan_id=${inner_vlan_id1} +| | ... | type_subif=two_tags dot1ad +| | ${vlan2_name} | ${vlan2_index}= | And Tagged Subinterface Created +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} +| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} +| | ... | type_subif=two_tags dot1ad +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-2-2 | push_dot1q=${False} +| | ... | tag1_id=${outer_vlan_id2} | tag2_id=${inner_vlan_wrong} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-2 +| | And Interfaces and VLAN sub-interfaces inter-connected using L2-xconnect +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Run Keyword And Expect Error | ICMP echo Rx timeout +| | ... | Send and receive ICMP Packet | ${tg_node} | ${tg_to_dut1} +| | ... | ${tg_to_dut2} | encaps=Dot1ad | vlan1=${outer_vlan_id1} +| | ... | vlan2=${inner_vlan_id1} + +| TC11: DUT1 and DUT2 with L2XC and VLAN translate-2-2 with wrong outer tag used (DUT1) switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv4-ICMPv4 on TG-DUT1 and \ +| | ... | on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 +| | ... | cross-connect (L2XC) with one interface to DUT2 and one Dot1ad +| | ... | sub-interface towards TG with VLAN tag rewrite translate-2-2 method to +| | ... | set outer tag different from outer tag set on Dot1ad sub-interface of +| | ... | DUT2; on DUT2 configure L2 cross-connect (L2XC) with one interface to +| | ... | TG and one Dot1ad sub-interface towards DUT1 with VLAN tag rewrite +| | ... | pop-1 tagged with Dot1ad tags from one of its interfaces to another +| | ... | one method. [Ver] Make TG send ICMPv4 Echo Req via DUT1 and DUT2; +| | ... | verify that packet is not received. [Ref] IEEE 802.1ad +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | ${vlan1_name} | ${vlan1_index}= | When Tagged Subinterface Created +| | ... | ${dut1_node} | ${dut1_to_tg} | ${subid} +| | ... | outer_vlan_id=${outer_vlan_id1} | inner_vlan_id=${inner_vlan_id1} +| | ... | type_subif=two_tags dot1ad +| | ${vlan2_name} | ${vlan2_index}= | And Tagged Subinterface Created +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} +| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} +| | ... | type_subif=two_tags dot1ad +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-2-2 | push_dot1q=${False} +| | ... | tag1_id=${outer_vlan_wrong} | tag2_id=${inner_vlan_id2} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-2 +| | And Interfaces and VLAN sub-interfaces inter-connected using L2-xconnect +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Run Keyword And Expect Error | ICMP echo Rx timeout +| | ... | Send and receive ICMP Packet | ${tg_node} | ${tg_to_dut1} +| | ... | ${tg_to_dut2} | encaps=Dot1ad | vlan1=${outer_vlan_id1} +| | ... | vlan2=${inner_vlan_id1} + +| TC12: DUT1 and DUT2 with L2XC and VLAN translate-2-2 with wrong outer and inner tags used (DUT1) switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1ad-IPv4-ICMPv4 on TG-DUT1 and \ +| | ... | on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 +| | ... | cross-connect (L2XC) with one interface to DUT2 and one Dot1ad +| | ... | sub-interface towards TG with VLAN tag rewrite translate-2-2 method to +| | ... | set tags different from tags set on Dot1ad sub-interface of DUT2; +| | ... | on DUT2 configure L2 cross-connect (L2XC) with one interface to TG +| | ... | and one Dot1ad sub-interface towards DUT1 with VLAN tag rewrite pop-1 +| | ... | tagged with Dot1ad tags from one of its interfaces to another one +| | ... | method. [Ver] Make TG send ICMPv4 Echo Req via DUT1 and DUT2; verify +| | ... | that packet is not received. [Ref] IEEE 802.1ad +| | Given Path for 3-node testing is set +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Interfaces in 3-node path are up +| | ${vlan1_name} | ${vlan1_index}= | When Tagged Subinterface Created +| | ... | ${dut1_node} | ${dut1_to_tg} | ${subid} +| | ... | outer_vlan_id=${outer_vlan_id1} | inner_vlan_id=${inner_vlan_id1} +| | ... | type_subif=two_tags dot1ad +| | ${vlan2_name} | ${vlan2_index}= | And Tagged Subinterface Created +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${subid} +| | ... | outer_vlan_id=${outer_vlan_id2} | inner_vlan_id=${inner_vlan_id2} +| | ... | type_subif=two_tags dot1ad +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-2-2 | push_dot1q=${False} +| | ... | tag1_id=${outer_vlan_wrong} | tag2_id=${inner_vlan_wrong} +| | And L2 Tag Rewrite Method Is Set On Interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-2 +| | And Interfaces and VLAN sub-interfaces inter-connected using L2-xconnect +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Run Keyword And Expect Error | ICMP echo Rx timeout +| | ... | Send and receive ICMP Packet | ${tg_node} | ${tg_to_dut1} +| | ... | ${tg_to_dut2} | encaps=Dot1ad | vlan1=${outer_vlan_id1} +| | ... | vlan2=${inner_vlan_id1} |