diff options
Diffstat (limited to 'tests/vpp/func/ip4_tunnels/lisp')
7 files changed, 778 insertions, 0 deletions
diff --git a/tests/vpp/func/ip4_tunnels/lisp/api-crud-lisp-func.robot b/tests/vpp/func/ip4_tunnels/lisp/api-crud-lisp-func.robot new file mode 100644 index 0000000000..118d657515 --- /dev/null +++ b/tests/vpp/func/ip4_tunnels/lisp/api-crud-lisp-func.robot @@ -0,0 +1,116 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Library | resources.libraries.python.topology.Topology +| Library | resources.libraries.python.NodePath +| Library | resources.libraries.python.Trace +| Library | resources.libraries.python.LispUtil +| Resource | resources/libraries/robot/shared/default.robot +| Resource | resources/libraries/robot/shared/interfaces.robot +| Resource | resources/libraries/robot/overlay/lisp_api.robot +# import additional Lisp settings from resource file +| Variables | resources/test_data/lisp/api/lisp_api_resources.py +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | 3_NODE_DOUBLE_LINK_TOPO +| ... | VM_ENV | HW_ENV +| ... +| Test Setup | Set up functional test +| ... +| Test Teardown | Tear down functional test +| ... +| Documentation | *API test cases* +| ... +| ... | *[Top] Network Topologies:* DUT1 1-node topology. +| ... | *[Enc] Packet Encapsulations:* None. +| ... | *[Cfg] DUT configuration:* DUT1 gets configured with all LISP +| ... | parameters. +| ... | *[Ver] Verification:* DUT1 operational data gets verified following +| ... | configuration. +| ... | *[Ref] Applicable standard specifications:* RFC6830. + +*** Variables *** +| ${locator_set_num}= | 3 + +*** Test Cases *** + +| TC01: DUT can enable and disable LISP +| | [Documentation] +| | ... | [Top] DUT1. [Enc] None. [Cfg1] Test LISP enable/disable API; On \ +| | ... | DUT1 enable LISP. [Ver1] Check DUT1 if LISP is enabled. [Cfg2] +| | ... | Then disable LISP. [Ver2] Check DUT1 if LISP is disabled. [Ref] +| | ... | RFC6830. +| | When Enable LISP | ${nodes['DUT1']} +| | Then LISP should be enabled | ${nodes['DUT1']} | ${lisp_status} +| | When Disable LISP | ${nodes['DUT1']} +| | Then LISP Should be disabled | ${nodes['DUT1']} | ${lisp_status} + +| TC02: DUT can add and delete locator_set +| | [Documentation] +| | ... | [Top] DUT1. [Enc] None. [Cfg1] Test LISP locator_set API; on \ +| | ... | DUT1 configure locator_set and locator. [Ver1] Check DUT1 +| | ... | configured locator_set and locator are correct. [Cfg2] Then +| | ... | remove locator_set and locator. [Ver2] check DUT1 locator_set +| | ... | and locator are removed. [Ref] RFC6830. +| | Given Generate LISP locator_set data +| | ... | ${nodes['DUT1']} | ${locator_set_num} +| | And Enable LISP | ${nodes['DUT1']} +| | When Configure LISP locator_set data | ${nodes['DUT1']} +| | Then LISP locator_set shpuld be configured correctly | ${nodes['DUT1']} +| | When Delete all LISP locator_set from VPP | ${nodes['DUT1']} +| | Then LISP locator_set should be unset | ${nodes['DUT1']} + +| TC03: DUT can add, reset and delete locator_set +| | [Documentation] +| | ... | [Top] DUT1. [Enc] None. [Cfg1] Test LISP locator_set API; on \ +| | ... | DUT1 configure locator_set and locator. [Ver1] Check DUT1 +| | ... | locator_set and locator are correct. [Cfg2] Then reset +| | ... | locator_set and set it again. [Ver2] Check DUT1 locator_set and +| | ... | locator are correct. [Cfg3] Then remove locator_set and locator. +| | ... | [Ver3] Check DUT1 all locator_set and locators are removed. +| | ... | [Ref] RFC6830. +| | Given Lisp locator_set data use for test reset locator_set are prepared +| | ... | ${nodes['DUT1']} | ${locator_set_num} +| | And Enable LISP | ${nodes['DUT1']} +| | When Configure LISP locator_set data | ${nodes['DUT1']} +| | Then LISP locator_set shpuld be configured correctly | ${nodes['DUT1']} +| | When Delete all LISP locator_set from VPP | ${nodes['DUT1']} +| | Then LISP locator_set should be unset | ${nodes['DUT1']} + +| TC04: DUT can add and delete eid address +| | [Documentation] +| | ... | [Top] DUT1. [Enc] None. [Cfg1] Test LISP eid API; on DUT1 \ +| | ... | configure LISP eid IP address. [Ver1] Check DUT1 configured data +| | ... | is correct. [Cfg2] Remove configured data. [Ver2] Check DUT1 all +| | ... | eid IP addresses are removed. [Ref] RFC6830. +| | Given Enable LISP | ${nodes['DUT1']} +| | When Configure LISP eid address | ${nodes['DUT1']} | ${eid_table} +| | Then LISP eid address should be set correctly to eid table +| | ... | ${nodes['DUT1']} | ${eid_table_vat} +| | When Delete all LISP eid address from VPP | ${nodes['DUT1']} | ${eid_table} +| | Then LISP eid table should be empty | ${nodes['DUT1']} + +| TC05: DUT can add and delete LISP map resolver address +| | [Documentation] +| | ... | [Top] DUT1. [Enc] None. [Cfg1] Test LISP map resolver address \ +| | ... | API; on DUT1 configure LISP map resolver address. [Ver1] Check +| | ... | DUT1 configured data is correct. [Cfg2] Remove configured data. +| | ... | [Ver2] Check DUT1 all map resolver addresses are removed. [Ref] +| | ... | RFC6830. +| | Given Enable LISP | ${nodes['DUT1']} +| | When Configure LISP map resolver address | ${nodes['DUT1']} | ${map_resolver} +| | Then LISP map resolver address should be configured correctly +| | ... | ${nodes['DUT1']} | ${map_resolver} +| | When Delete all LISP map resolver address from VPP +| | ... | ${nodes['DUT1']} | ${map_resolver} +| | Then LISP map resolver address should be empty | ${nodes['DUT1']} diff --git a/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lisp-ip4base-func.robot b/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lisp-ip4base-func.robot new file mode 100644 index 0000000000..ae9485c3b8 --- /dev/null +++ b/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lisp-ip4base-func.robot @@ -0,0 +1,124 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| Resource | resources/libraries/robot/shared/testing_path.robot +| Resource | resources/libraries/robot/ip/ip4.robot +| Resource | resources/libraries/robot/shared/traffic.robot +| Resource | resources/libraries/robot/overlay/lisp_static_adjacency.robot +| Resource | resources/libraries/robot/l2/l2_traffic.robot +| Library | resources.libraries.python.IPUtil +| Library | resources.libraries.python.Trace +# import additional Lisp settings from resource file +| Variables | resources/test_data/lisp/static_adjacency/lisp_static_adjacency.py +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | 3_NODE_DOUBLE_LINK_TOPO +| ... | VM_ENV | HW_ENV +| ... +| Test Setup | Set up functional test +| ... +| Test Teardown | Tear down functional test +| ... +| Documentation | *IP AFI independent functional tests.* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2,\ +| ... | Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\ +| ... | routing and static routes. LISPoIPv4 tunnel is\ +| ... | configured between DUT1 and DUT2. +| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets\ +| ... | are sent in both directions by TG on links to DUT1 and DUT2; on receive\ +| ... | TG verifies packets for correctness and their IPv4 src-addr,\ +| ... | dst-addr and MAC addresses. +| ... | *[Ref] Applicable standard specifications:* RFC6830. + +*** Test Cases *** +| TC01: DUT1 and DUT2 route IPv4 over LISPoIPv4 tunnel after disable-enable +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. +| | ... | [Enc] Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on\ +| | ... | TG-DUTn. +| | ... | [Cfg1] On DUT1 and DUT2 configure IPv4 LISP static adjacencies. +| | ... | [Ver1] Make TG send ICMPv4 Echo Req between its interfaces across\ +| | ... | both DUTs and LISP tunnel between them; verify IPv4 headers on\ +| | ... | received packets are correct. +| | ... | [Cfg2] Disable LISP. +| | ... | [Ver2] Verify packets are not received via LISP tunnel. +| | ... | [Cfg3] Re-enable LISP. +| | ... | [Ver3] Verify packets are received again via LISP tunnel. +| | ... | [Ref] RFC6830. +| | Given Configure path in 3-node circular topology +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Set interfaces in 3-node circular topology up +| | And Configure IP addresses on interfaces +| | ... | ${dut1_node} | ${dut1_to_dut2} +| | ... | ${dut1_to_dut2_ip4} | ${prefix4} +| | ... | ${dut1_node} | ${dut1_to_tg} +| | ... | ${dut1_to_tg_ip4} | ${prefix4} +| | ... | ${dut2_node} | ${dut2_to_dut1} +| | ... | ${dut2_to_dut1_ip4} | ${prefix4} +| | ... | ${dut2_node} | ${dut2_to_tg} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And VPP IP Probe | ${dut1_node} | ${dut1_to_dut2} | ${dut2_to_dut1_ip4} +| | And VPP IP Probe | ${dut2_node} | ${dut2_to_dut1} | ${dut1_to_dut2_ip4} +| | And Add Arp On Dut | ${dut2_node} | ${dut2_to_tg} | ${tg2_ip4} +| | ... | ${tg_to_dut2_mac} +| | And Add Arp On Dut | ${dut1_node} | ${dut1_to_tg} | ${tg1_ip4} +| | ... | ${tg_to_dut1_mac} +| | When Configure LISP topology in 3-node circular topology +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${NONE} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_to_dut2_ip4_static_adjacency} +| | ... | ${dut2_to_dut1_ip4_static_adjacency} +| | Then Send packet and verify headers +| | ... | ${tg_node} | ${tg1_ip4} | ${tg2_ip4} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Send packet and verify headers +| | ... | ${tg_node} | ${tg2_ip4} | ${tg1_ip4} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} +| | When Disable Lisp | ${dut1_node} +| | Then Packet transmission from port to port should fail +| | ... | ${tg_node} | ${tg1_ip4} | ${tg2_ip4} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Packet transmission from port to port should fail +| | ... | ${tg_node} | ${tg2_ip4} | ${tg1_ip4} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} +| | When Enable Lisp | ${dut1_node} +| | And Vpp Add Lisp Adjacency | ${dut1_node} +| | ... | ${dut1_to_dut2_ip4_static_adjacency['vni']} +| | ... | ${dut1_to_dut2_ip4_static_adjacency['deid']} +| | ... | ${dut1_to_dut2_ip4_static_adjacency['prefix']} +| | ... | ${dut1_to_dut2_ip4_static_adjacency['seid']} +| | ... | ${dut1_to_dut2_ip4_static_adjacency['prefix']} +| | And Vpp Add Lisp Adjacency | ${dut2_node} +| | ... | ${dut2_to_dut1_ip4_static_adjacency['vni']} +| | ... | ${dut2_to_dut1_ip4_static_adjacency['deid']} +| | ... | ${dut2_to_dut1_ip4_static_adjacency['prefix']} +| | ... | ${dut2_to_dut1_ip4_static_adjacency['seid']} +| | ... | ${dut2_to_dut1_ip4_static_adjacency['prefix']} +| | Then Wait Until Keyword Succeeds | 2x | 5s | Send packet and verify headers +| | ... | ${tg_node} | ${tg1_ip4} | ${tg2_ip4} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Wait Until Keyword Succeeds | 2x | 5s | Send packet and verify headers +| | ... | ${tg_node} | ${tg2_ip4} | ${tg1_ip4} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} diff --git a/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lisp-l2bdbasemaclrn-func.robot b/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lisp-l2bdbasemaclrn-func.robot new file mode 100644 index 0000000000..98602fc45f --- /dev/null +++ b/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lisp-l2bdbasemaclrn-func.robot @@ -0,0 +1,95 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Library | resources.libraries.python.topology.Topology +| Library | resources.libraries.python.NodePath +| Library | resources.libraries.python.Trace +| Library | resources.libraries.python.IPUtil +| Library | resources.libraries.python.LispUtil +| Library | resources.libraries.python.L2Util +| Resource | resources/libraries/robot/shared/traffic.robot +| Resource | resources/libraries/robot/shared/default.robot +| Resource | resources/libraries/robot/shared/interfaces.robot +| Resource | resources/libraries/robot/shared/testing_path.robot +| Resource | resources/libraries/robot/ip/ip4.robot +| Resource | resources/libraries/robot/overlay/l2lisp.robot +# Import configuration and test data: +| Variables | resources/test_data/lisp/l2/l2_ipv4.py +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | VM_ENV | LISP +| ... +| Test Setup | Set up functional test +| ... +| Test Teardown | Tear down functional test +| ... +| Documentation | *ip4-lispgpe-ip4 encapsulation test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-ICMPv4-LISPGpe-IP4 +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\ +| ... | routing and static routes. LISPoIPv4 tunnel is configured between\ +| ... | DUT1 and DUT2. +| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets are sent in\ +| ... | both directions by TG on links to DUT1 and DUT2; on receive\ +| ... | TG verifies packets for correctness and their IPv4 src-addr, dst-addr\ +| ... | and MAC addresses. +| ... | *[Ref] Applicable standard specifications:* RFC6830. + +*** Test Cases *** +| TC01: Route IPv4 packet through LISP with Bridge Domain setup. +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. +| | ... | [Enc] Eth-IPv4-ICMPv4-LISPGpe-IP4 +| | ... | [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2. Also\ +| | ... | configure BD and assign it to LISP VNI. +| | ... | [Ver] Make TG send ICMPv4 Echo Req between its interfaces across both\ +| | ... | DUTs and LISP tunnel between them; verify IPv4, Ether headers on\ +| | ... | received packets are correct. +| | ... | [Ref] RFC6830. +| | ... +| | Given Configure path in 3-node circular topology +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Set interfaces in 3-node circular topology up +| | And Configure IP addresses on interfaces +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${dut1_to_dut2_ip4} | ${prefix4} +| | ... | ${dut1_node} | ${dut1_to_tg} | ${dut1_to_tg_ip4} | ${prefix4} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${dut2_to_dut1_ip4} | ${prefix4} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${dut2_to_tg_ip4} | ${prefix4} +| | And Add Arp On Dut | ${dut2_node} | ${dut2_to_tg} | ${tg2_ip4} +| | ... | ${tg_to_dut2_mac} +| | And Add Arp On Dut | ${dut1_node} | ${dut1_to_tg} | ${tg1_ip4} +| | ... | ${tg_to_dut1_mac} +| | And Add Arp On Dut | ${dut1_node} | ${dut1_to_dut2} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_dut1_mac} +| | And Add Arp On Dut | ${dut2_node} | ${dut2_to_dut1} | ${dut1_to_dut2_ip4} +| | ... | ${dut1_to_dut2_mac} +| | When Create L2 BD | ${dut1_node} | ${vpp_bd_id} +| | And Add Interface To L2 BD | ${dut1_node} | ${dut1_to_tg} | ${vpp_bd_id} +| | And Create L2 BD | ${dut2_node} | ${vpp_bd_id} +| | And Add Interface To L2 BD | ${dut2_node} | ${dut2_to_tg} | ${vpp_bd_id} +| | And Configure L2 LISP on DUT | ${dut1_node} +| | ... | ${dut1_to_dut2_ip4_static_adjacency} +| | ... | ${lisp_dut_settings} +| | And Configure L2 LISP on DUT | ${dut2_node} +| | ... | ${dut2_to_dut1_ip4_static_adjacency} +| | ... | ${lisp_dut_settings} +| | Then Send packet and verify headers +| | ... | ${tg_node} | ${tg1_ip4} | ${tg2_ip4} +| | ... | ${tg_to_dut1} | ${tg_if1_mac} | ${tg_if2_mac} +| | ... | ${tg_to_dut2} | ${tg_if1_mac} | ${tg_if2_mac} +| | And Send packet and verify headers +| | ... | ${tg_node} | ${tg2_ip4} | ${tg1_ip4} +| | ... | ${tg_to_dut2} | ${tg_if2_mac} | ${tg_if1_mac} +| | ... | ${tg_to_dut1} | ${tg_if2_mac} | ${tg_if1_mac} diff --git a/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lispgpe-ip4base-func.robot b/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lispgpe-ip4base-func.robot new file mode 100644 index 0000000000..90a0ae1599 --- /dev/null +++ b/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lispgpe-ip4base-func.robot @@ -0,0 +1,104 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Library | resources.libraries.python.topology.Topology +| Library | resources.libraries.python.NodePath +| Library | resources.libraries.python.Trace +| Library | resources.libraries.python.IPUtil +| Library | resources.libraries.python.VPPUtil +| Library | resources.libraries.python.InterfaceUtil +| Library | resources.libraries.python.VhostUser +| Resource | resources/libraries/robot/shared/traffic.robot +| Resource | resources/libraries/robot/shared/default.robot +| Resource | resources/libraries/robot/shared/interfaces.robot +| Resource | resources/libraries/robot/shared/testing_path.robot +| Resource | resources/libraries/robot/ip/ip4.robot +| Resource | resources/libraries/robot/vrf.robot +| Resource | resources/libraries/robot/vm/qemu.robot +| Resource | resources/libraries/robot/l2/l2_bridge_domain.robot +| Resource | resources/libraries/robot/overlay/lispgpe.robot +# Import configuration and test data: +| Variables | resources/test_data/lisp/ipv4_lispgpe_ipv4/ipv4_lispgpe_ipv4.py +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | VM_ENV | LISP +| ... +| Test Setup | Set up functional test +| ... +| Test Teardown | Tear down LISP functional test +| ... +| Documentation | *ip4-lispgpe-ip4 encapsulation test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2,\ +| ... | Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\ +| ... | routing and static routes. LISPoIPv4 tunnel is configured between\ +| ... | DUT1 and DUT2. +| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets are sent in\ +| ... | both directions by TG on links to DUT1 and DUT2; on receive\ +| ... | TG verifies packets for correctness and their IPv4 src-addr, dst-addr\ +| ... | and MAC addresses. +| ... | *[Ref] Applicable standard specifications:* RFC6830. + +*** Test Cases *** +| TC01: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using physical interfaces +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. +| | ... | [Enc] Eth-IPv4-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on\ +| | ... | TG-DUTn. +| | ... | [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2. +| | ... | [Ver] Case: ip4-lispgpe-ip4 - phy2lisp +| | ... | Make TG send ICMPv4 Echo Req between its interfaces across both\ +| | ... | DUTs and LISP GPE tunnel between them; verify IPv4 headers on\ +| | ... | received packets are correct. +| | ... | [Ref] RFC6830. +| | ... +| | Given Configure path in 3-node circular topology +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Set interfaces in 3-node circular topology up +| | And Configure IP addresses on interfaces +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${dut1_to_dut2_ip4} | ${prefix4} +| | ... | ${dut1_node} | ${dut1_to_tg} | ${dut1_to_tg_ip4} | ${prefix4} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${dut2_to_dut1_ip4} | ${prefix4} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${dut2_to_tg_ip4} | ${prefix4} +| | And Add IP Neighbors +| | When Configure LISP GPE topology in 3-node circular topology +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${NONE} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_to_dut2_ip4_static_adjacency} +| | ... | ${dut2_to_dut1_ip4_static_adjacency} +| | Then Send packet and verify headers +| | ... | ${tg_node} | ${tg1_ip4} | ${tg2_ip4} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Send packet and verify headers +| | ... | ${tg_node} | ${tg2_ip4} | ${tg1_ip4} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} + +*** Keywords *** +| Add IP Neighbors +| | [Documentation] +| | ... | Add IP neighbors to physical interfaces on DUTs. +| | ... +| | Add IP Neighbor | ${dut1_node} | ${dut1_to_tg} | ${tg1_ip4} +| | ... | ${tg_to_dut1_mac} +| | Add IP Neighbor | ${dut2_node} | ${dut2_to_tg} | ${tg2_ip4} +| | ... | ${tg_to_dut2_mac} +| | Add IP Neighbor | ${dut1_node} | ${dut1_to_dut2} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_dut1_mac} +| | Add IP Neighbor | ${dut2_node} | ${dut2_to_dut1} | ${dut1_to_dut2_ip4} +| | ... | ${dut1_to_dut2_mac} diff --git a/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lispgpe-ip4basevrf-func.robot b/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lispgpe-ip4basevrf-func.robot new file mode 100644 index 0000000000..f41be5fecc --- /dev/null +++ b/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lispgpe-ip4basevrf-func.robot @@ -0,0 +1,109 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Library | resources.libraries.python.topology.Topology +| Library | resources.libraries.python.NodePath +| Library | resources.libraries.python.Trace +| Library | resources.libraries.python.IPUtil +| Library | resources.libraries.python.VPPUtil +| Library | resources.libraries.python.InterfaceUtil +| Library | resources.libraries.python.VhostUser +| Resource | resources/libraries/robot/shared/traffic.robot +| Resource | resources/libraries/robot/shared/default.robot +| Resource | resources/libraries/robot/shared/interfaces.robot +| Resource | resources/libraries/robot/shared/testing_path.robot +| Resource | resources/libraries/robot/ip/ip4.robot +| Resource | resources/libraries/robot/vrf.robot +| Resource | resources/libraries/robot/vm/qemu.robot +| Resource | resources/libraries/robot/l2/l2_bridge_domain.robot +| Resource | resources/libraries/robot/overlay/lispgpe.robot +# Import configuration and test data: +| Variables | resources/test_data/lisp/ipv4_lispgpe_ipv4/ipv4_lispgpe_ipv4.py +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | VM_ENV | LISP +| ... +| Test Setup | Set up functional test +| ... +| Test Teardown | Tear down LISP functional test +| ... +| Documentation | *ip4-lispgpe-ip4 encapsulation test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2,\ +| ... | Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\ +| ... | routing and static routes. LISPoIPv4 tunnel is configured between\ +| ... | DUT1 and DUT2. +| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets are sent in\ +| ... | both directions by TG on links to DUT1 and DUT2; on receive\ +| ... | TG verifies packets for correctness and their IPv4 src-addr, dst-addr\ +| ... | and MAC addresses. +| ... | *[Ref] Applicable standard specifications:* RFC6830. + +*** Test Cases *** +| TC01: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using physical interfaces and VRF is enabled +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. +| | ... | [Enc] Eth-IPv4-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on\ +| | ... | TG-DUTn. +| | ... | [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2. +| | ... | [Ver] Case: ip4-lispgpe-ip4 - vrf, phy2lisp +| | ... | Make TG send ICMPv4 Echo Req between its interfaces across both\ +| | ... | DUTs and LISP GPE tunnel between them; verify IPv4 headers on\ +| | ... | received packets are correct. +| | ... | [Ref] RFC6830. +| | ... +| | Given Configure path in 3-node circular topology +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Set interfaces in 3-node circular topology up +| | And Assign Interface To Fib Table | ${dut1_node} +| | ... | ${dut1_to_tg} | ${fib_table_1} +| | And Assign Interface To Fib Table | ${dut2_node} +| | ... | ${dut2_to_tg} | ${fib_table_1} +| | And Add IP Neighbors +| | And Configure IP addresses on interfaces +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${dut1_to_dut2_ip4} | ${prefix4} +| | ... | ${dut1_node} | ${dut1_to_tg} | ${dut1_to_tg_ip4} | ${prefix4} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${dut2_to_dut1_ip4} | ${prefix4} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${dut2_to_tg_ip4} | ${prefix4} +| | When Configure LISP GPE topology in 3-node circular topology +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${NONE} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_to_dut2_ip4_static_adjacency} +| | ... | ${dut2_to_dut1_ip4_static_adjacency} +| | ... | ${dut1_dut2_vni} | ${fib_table_1} +| | Then Send packet and verify headers +| | ... | ${tg_node} | ${tg1_ip4} | ${tg2_ip4} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Send packet and verify headers +| | ... | ${tg_node} | ${tg2_ip4} | ${tg1_ip4} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} + +*** Keywords *** +| Add IP Neighbors +| | [Documentation] +| | ... | Add IP neighbors to physical interfaces on DUTs. +| | ... +| | Add IP Neighbor | ${dut1_node} | ${dut1_to_tg} | ${tg1_ip4} +| | ... | ${tg_to_dut1_mac} +| | Add IP Neighbor | ${dut2_node} | ${dut2_to_tg} | ${tg2_ip4} +| | ... | ${tg_to_dut2_mac} +| | Add IP Neighbor | ${dut1_node} | ${dut1_to_dut2} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_dut1_mac} +| | Add IP Neighbor | ${dut2_node} | ${dut2_to_dut1} | ${dut1_to_dut2_ip4} +| | ... | ${dut1_to_dut2_mac} diff --git a/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lispgpe-ip6base-func.robot b/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lispgpe-ip6base-func.robot new file mode 100644 index 0000000000..7e97aca29e --- /dev/null +++ b/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lispgpe-ip6base-func.robot @@ -0,0 +1,120 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| Resource | resources/libraries/robot/shared/testing_path.robot +| Resource | resources/libraries/robot/ip/ip4.robot +| Resource | resources/libraries/robot/shared/traffic.robot +| Resource | resources/libraries/robot/overlay/lisp_static_adjacency.robot +| Resource | resources/libraries/robot/l2/l2_traffic.robot +| Resource | resources/libraries/robot/overlay/lispgpe.robot +| Resource | resources/libraries/robot/l2/l2_bridge_domain.robot +| Resource | resources/libraries/robot/vm/qemu.robot +| Library | resources.libraries.python.IPUtil +| Library | resources.libraries.python.VhostUser +| Library | resources.libraries.python.Trace +| Library | resources.libraries.python.VPPUtil +# import additional Lisp settings from resource file +| Variables | resources/test_data/lisp/static_adjacency/lisp_static_adjacency.py +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | 3_NODE_DOUBLE_LINK_TOPO +| ... | VM_ENV | HW_ENV +| ... +| Test Setup | Set up functional test +| ... +| Test Teardown | Tear down functional test +| ... +| Documentation | *LISP static adjacency test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2,\ +| ... | Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv4 tunnel. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6\ +| ... | routing and static routes. LISPoIPv4 tunnel is configured\ +| ... | between DUT1 and DUT2. +| ... | *[Ver] TG verification:* Test ICMPv6 Echo Request packets\ +| ... | are sent in both directions by TG on links to DUT1 and DUT2; on receive\ +| ... | TG verifies packets for correctness and their IPv6 src-addr,\ +| ... | dst-addr and MAC addresses. +| ... | *[Ref] Applicable standard specifications:* RFC6830. + +*** Test Cases *** +| TC01: DUT1 and DUT2 route IPv6 bidirectionally over LISPoIPv4 tunnel +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. +| | ... | [Enc] Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on\ +| | ... | TG-DUTn. +| | ... | [Cfg] On DUT1 and DUT2 configure IPv4 LISP static adjacencies. +| | ... | [Ver] Make TG send ICMPv6 Echo Req between its interfaces across both\ +| | ... | DUTs and LISP tunnel between them; verify IPv6 headers on received\ +| | ... | packets are correct. +| | ... | [Cfg2] Reconf LISP. +| | ... | [Ver2] Verify packets are received again via LISP tunnel. +| | ... | [Ref] RFC6830. +| | Given Configure path in 3-node circular topology +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Set interfaces in 3-node circular topology up +| | And Configure IP addresses on interfaces +| | ... | ${dut1_node} | ${dut1_to_dut2} +| | ... | ${dut1_to_dut2_ip6o4} | ${dut_prefix6o4} +| | ... | ${dut1_node} | ${dut1_to_tg} +| | ... | ${dut1_to_tg_ip6o4} | ${tg_prefix6o4} +| | ... | ${dut2_node} | ${dut2_to_dut1} +| | ... | ${dut2_to_dut1_ip6o4} | ${dut_prefix6o4} +| | ... | ${dut2_node} | ${dut2_to_tg} +| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} +| | And Add IP Neighbors +| | And Vpp All RA Suppress Link Layer | ${nodes} +| | When Configure LISP topology in 3-node circular topology +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${NONE} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} +| | Then Send packet and verify headers +| | ... | ${tg_node} | ${tg1_ip6o4} | ${tg2_ip6o4} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Send packet and verify headers +| | ... | ${tg_node} | ${tg2_ip6o4} | ${tg1_ip6o4} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} +| | When Change LISP Configuration | ${dut1_node} | ${dut2_node} +| | ... | ${dut1_to_dut2} | ${dut2_to_dut1} | ${dut1_to_dut2_mac} +| | ... | ${dut2_to_dut1_mac} | ${dut1_to_dut2_ip6o4} +| | ... | ${dut2_to_dut1_ip6o4_reconf} | ${dut_prefix6o4} +| | ... | ${dut1_ip6o4_static_adjacency} +| | ... | ${dut1_ip6o4_static_adjacency_reconf} +| | Then Send packet and verify headers +| | ... | ${tg_node} | ${tg1_ip6o4} | ${tg2_ip6o4} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Send packet and verify headers +| | ... | ${tg_node} | ${tg2_ip6o4} | ${tg1_ip6o4} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} + +*** Keywords *** +| Add IP Neighbors +| | [Documentation] +| | ... | Add IP neighbors to physical interfaces on DUTs. +| | ... +| | Add IP Neighbor | ${dut1_node} | ${dut1_to_tg} | ${tg1_ip6o4} +| | ... | ${tg_to_dut1_mac} +| | Add IP Neighbor | ${dut2_node} | ${dut2_to_tg} | ${tg2_ip6o4} +| | ... | ${tg_to_dut2_mac} +| | Add IP Neighbor | ${dut1_node} | ${dut1_to_dut2} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_dut1_mac} +| | Add IP Neighbor | ${dut2_node} | ${dut2_to_dut1} | ${dut1_to_dut2_ip6o4} +| | ... | ${dut1_to_dut2_mac} diff --git a/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lispgpe-ip6basevrf-func.robot b/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lispgpe-ip6basevrf-func.robot new file mode 100644 index 0000000000..668e870ff0 --- /dev/null +++ b/tests/vpp/func/ip4_tunnels/lisp/eth2p-ethip4lispgpe-ip6basevrf-func.robot @@ -0,0 +1,110 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| Resource | resources/libraries/robot/shared/testing_path.robot +| Resource | resources/libraries/robot/ip/ip4.robot +| Resource | resources/libraries/robot/shared/traffic.robot +| Resource | resources/libraries/robot/overlay/lisp_static_adjacency.robot +| Resource | resources/libraries/robot/l2/l2_traffic.robot +| Resource | resources/libraries/robot/overlay/lispgpe.robot +| Resource | resources/libraries/robot/l2/l2_bridge_domain.robot +| Resource | resources/libraries/robot/vm/qemu.robot +| Library | resources.libraries.python.IPUtil +| Library | resources.libraries.python.VhostUser +| Library | resources.libraries.python.Trace +| Library | resources.libraries.python.VPPUtil +# import additional Lisp settings from resource file +| Variables | resources/test_data/lisp/static_adjacency/lisp_static_adjacency.py +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | 3_NODE_DOUBLE_LINK_TOPO +| ... | VM_ENV | HW_ENV +| ... +| Test Setup | Set up functional test +| ... +| Test Teardown | Tear down LISP functional test +| ... +| Documentation | *LISP static adjacency test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2,\ +| ... | Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv4 tunnel. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6\ +| ... | routing and static routes. LISPoIPv4 tunnel is configured\ +| ... | between DUT1 and DUT2. +| ... | *[Ver] TG verification:* Test ICMPv6 Echo Request packets\ +| ... | are sent in both directions by TG on links to DUT1 and DUT2; on receive\ +| ... | TG verifies packets for correctness and their IPv6 src-addr,\ +| ... | dst-addr and MAC addresses. +| ... | *[Ref] Applicable standard specifications:* RFC6830. + +*** Test Cases *** +| TC01: DUT1 and DUT2 route IPv6 bidirectionally over LISP GPE tunnel using physical interfaces and VRF is enabled +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. +| | ... | [Enc] Eth-IPv4-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on\ +| | ... | TG-DUTn. +| | ... | [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2. +| | ... | [Ver] Case: ip6-lispgpe-ip4 - vrf, phy2lisp +| | ... | Make TG send ICMPv4 Echo Req between its interfaces across both\ +| | ... | DUTs and LISP GPE tunnel between them; verify IPv6 headers on\ +| | ... | received packets are correct. +| | ... | [Ref] RFC6830. +| | ... +| | Given Configure path in 3-node circular topology +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Set interfaces in 3-node circular topology up +| | And Assign Interface To Fib Table | ${dut1_node} +| | ... | ${dut1_to_tg} | ${fib_table_1} | ip6=${TRUE} +| | And Assign Interface To Fib Table | ${dut2_node} +| | ... | ${dut2_to_tg} | ${fib_table_1} | ip6=${TRUE} +| | And Add IP Neighbors +| | And Configure IP addresses on interfaces +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${dut1_to_dut2_ip6o4} +| | ... | ${dut_prefix6o4} +| | ... | ${dut1_node} | ${dut1_to_tg} | ${dut1_to_tg_ip6o4} | ${tg_prefix6o4} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut_prefix6o4} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} +| | And Vpp All RA Suppress Link Layer | ${nodes} +| | When Configure LISP GPE topology in 3-node circular topology +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${NONE} +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} +| | ... | ${dut1_ip6o4_static_adjacency} +| | ... | ${dut2_ip6o4_static_adjacency} +| | ... | ${dut1_dut2_vni} | ${fib_table_1} +| | Then Send packet and verify headers +| | ... | ${tg_node} | ${tg1_ip6o4} | ${tg2_ip6o4} +| | ... | ${tg_to_dut1} | ${tg_to_dut1_mac} | ${dut1_to_tg_mac} +| | ... | ${tg_to_dut2} | ${dut2_to_tg_mac} | ${tg_to_dut2_mac} +| | And Send packet and verify headers +| | ... | ${tg_node} | ${tg2_ip6o4} | ${tg1_ip6o4} +| | ... | ${tg_to_dut2} | ${tg_to_dut2_mac} | ${dut2_to_tg_mac} +| | ... | ${tg_to_dut1} | ${dut1_to_tg_mac} | ${tg_to_dut1_mac} + +*** Keywords *** +| Add IP Neighbors +| | [Documentation] +| | ... | Add IP neighbors to physical interfaces on DUTs. +| | ... +| | Add IP Neighbor | ${dut1_node} | ${dut1_to_tg} | ${tg1_ip6o4} +| | ... | ${tg_to_dut1_mac} +| | Add IP Neighbor | ${dut2_node} | ${dut2_to_tg} | ${tg2_ip6o4} +| | ... | ${tg_to_dut2_mac} +| | Add IP Neighbor | ${dut1_node} | ${dut1_to_dut2} | ${dut2_to_dut1_ip6o4} +| | ... | ${dut2_to_dut1_mac} +| | Add IP Neighbor | ${dut2_node} | ${dut2_to_dut1} | ${dut1_to_dut2_ip6o4} +| | ... | ${dut1_to_dut2_mac} |