diff options
Diffstat (limited to 'tests/vpp/func/l2xc/eth2p-dot1q-l2xcbase-vlantrans11-func.robot')
| -rw-r--r-- | tests/vpp/func/l2xc/eth2p-dot1q-l2xcbase-vlantrans11-func.robot | 171 |
1 files changed, 171 insertions, 0 deletions
diff --git a/tests/vpp/func/l2xc/eth2p-dot1q-l2xcbase-vlantrans11-func.robot b/tests/vpp/func/l2xc/eth2p-dot1q-l2xcbase-vlantrans11-func.robot new file mode 100644 index 0000000000..49039e9db9 --- /dev/null +++ b/tests/vpp/func/l2xc/eth2p-dot1q-l2xcbase-vlantrans11-func.robot @@ -0,0 +1,171 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| Resource | resources/libraries/robot/shared/testing_path.robot +| Resource | resources/libraries/robot/l2/tagging.robot +| Resource | resources/libraries/robot/l2/l2_traffic.robot +| Library | resources.libraries.python.Trace +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | HW_ENV | VM_ENV | SKIP_VPP_PATCH +| Test Setup | Set up functional test +| Test Teardown | Tear down functional test +| Documentation | *L2XC with VLAN tag rewrite test cases - translate-1-1* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet encapsulations:* Eth-dot1q-IPv4-ICMPv4 or +| ... | Eth-dot1q-IPv6-ICMPv6 on TG-DUT1 and DUT1-DUT2, Eth-IPv4-ICMPv4 or +| ... | Eth-IPv4-ICMPv4 on TG-DUT2 for L2 switching of IPv4/IPv6. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 cross-connect +| ... | (L2XC) switching between VLAN sub-interface with VLAN tag rewrite +| ... | translate-1-1 method of interface towards TG and interface towards DUT2. +| ... | DUT2 is configured configured with L2 cross-connect (L2XC) switching +| ... | between VLAN sub-interface with VLAN tag rewrite pop-1 method +| ... | of interface towards DUT1 and interface towards TG. +| ... | *[Ver] TG verification:* Test ICMPv4 Echo Request packets are +| ... | sent from TG on link to DUT1 and received in TG on link form DUT2; +| ... | on receive TG verifies packets for correctness and their IPv4 src-addr, +| ... | dst-addr and MAC addresses. +| ... | *[Ref] Applicable standard specifications:* IEEE 802.1q, IEEE 802.1ad. + +*** Variables *** +| ${subid}= | 10 + +| ${outer_vlan_id1}= | 110 +| ${outer_vlan_id2}= | 120 +| ${outer_vlan_wrong}= | 150 + +| ${src_ip}= | 3ffe:63::1 +| ${dst_ip}= | 3ffe:63::2 + +*** Test Cases *** +| TC01: DUT1 and DUT2 with L2XC and VLAN translate-1-1 (DUT1) switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1 and \ +| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 +| | ... | cross-connect (L2XC) with one interface to DUT2 and one VLAN +| | ... | sub-interface towards TG with VLAN tag rewrite translate-1-1 method; +| | ... | on DUT2 configure L2 cross-connect (L2XC) with one interface to TG +| | ... | and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 +| | ... | method. [Ver] Make TG send ICMPv4 Echo Req tagged with one Dot1q tag +| | ... | from one of its interfaces to another one via DUT1 and DUT2; verify +| | ... | that packet is received. [Ref] IEEE 802.1q +| | Given Configure path in 3-node circular topology +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Set interfaces in 3-node circular topology up +| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface +| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} +| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} +| | And Configure L2 tag rewrite method on interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_id2} +| | And Configure L2 tag rewrite method on interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-1 +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Send ICMP packet and verify received packet +| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | encaps=Dot1q +| | ... | vlan1=${outer_vlan_id1} + +| TC02: DUT1 and DUT2 with L2XC and VLAN translate-1-1 with wrong tag used (DUT1) switch ICMPv4 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv4-ICMPv4 on TG-DUT1 and \ +| | ... | DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUT2. [Cfg] On DUT1 configure L2 +| | ... | cross-connect (L2XC) with one VLAN tagged sub-interface to DUT2 and +| | ... | one VLAN sub-interface towards TG with VLAN tag rewrite +| | ... | (translate-1-1) on sub-interface to DUT2; on DUT2 configure L2XC with +| | ... | one interface to TG and one VLAN sub-interface towards DUT1 with VLAN +| | ... | tag pop-1. [Ver] Make TG send ICMPv4 Echo Req tagged with one dot1q +| | ... | tag from one of its interfaces to another one via DUT1 and DUT2; +| | ... | verify that packet is not received. [Ref] IEEE 802.1q +| | [Tags] | SKIP_PATCH +| | Given Configure path in 3-node circular topology +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Set interfaces in 3-node circular topology up +| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface +| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} +| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} +| | And Configure L2 tag rewrite method on interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_wrong} +| | And Configure L2 tag rewrite method on interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-1 +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Run Keyword And Expect Error | ICMP echo Rx timeout +| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} +| | ... | ${tg_to_dut2} | encaps=Dot1q | vlan1=${outer_vlan_id1} + +| TC03: DUT1 and DUT2 with L2XC and VLAN translate-1-1 (DUT1) switch ICMPv6 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1 and \ +| | ... | DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 +| | ... | cross-connect (L2XC) with one interface to DUT2 and one VLAN +| | ... | sub-interface towards TG with VLAN tag rewrite translate-1-1 method; +| | ... | on DUT2 configure L2 cross-connect (L2XC) with one interface to TG +| | ... | and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 +| | ... | method. [Ver] Make TG send ICMPv6 Echo Req tagegd with one Dot1q tag +| | ... | from one of its interfaces to another one via DUT1 and DUT2; verify +| | ... | that packet is received. [Ref] IEEE 802.1q +| | Given Configure path in 3-node circular topology +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Set interfaces in 3-node circular topology up +| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface +| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} +| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} +| | And Configure L2 tag rewrite method on interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_id2} +| | And Configure L2 tag rewrite method on interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-1 +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Send ICMP packet and verify received packet +| | ... | ${tg_node} | ${tg_to_dut1} | ${tg_to_dut2} | src_ip=${src_ip} +| | ... | dst_ip=${dst_ip} | encaps=Dot1q | vlan1=${outer_vlan_id1} + +| TC04: DUT1 and DUT2 with L2XC and VLAN translate-1-1 with wrong tag used (DUT1) switch ICMPv6 between two TG links +| | [Documentation] +| | ... | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-dot1q-IPv6-ICMPv6 on TG-DUT1 and \ +| | ... | DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUT2. [Cfg] On DUT1 configure L2 +| | ... | cross-connect (L2XC) with one interface to DUT2 and one VLAN +| | ... | sub-interface towards TG with VLAN tag rewrite translate-1-1 method +| | ... | to set tag different from tag set on VLAN sub-interface of DUT2; +| | ... | on DUT2 configure L2 cross-connect (L2XC) with one interface to TG +| | ... | and one VLAN sub-interface towards DUT1 with VLAN tag rewrite pop-1 +| | ... | method. [Ver] Make TG send ICMPv6 Echo Req tagegd with one Dot1q tag +| | ... | from one of its interfaces to another one via DUT1 and DUT2; verify +| | ... | that packet is not received. [Ref] IEEE 802.1q +| | [Tags] | SKIP_PATCH +| | Given Configure path in 3-node circular topology +| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['DUT2']} | ${nodes['TG']} +| | And Set interfaces in 3-node circular topology up +| | ${vlan1_name} | ${vlan1_index}= | When Create vlan sub-interface +| | ... | ${dut1_node} | ${dut1_to_tg} | ${outer_vlan_id1} +| | ${vlan2_name} | ${vlan2_index}= | And Create vlan sub-interface +| | ... | ${dut2_node} | ${dut2_to_dut1} | ${outer_vlan_id2} +| | And Configure L2 tag rewrite method on interface | ${dut1_node} +| | ... | ${vlan1_index} | translate-1-1 | tag1_id=${outer_vlan_wrong} +| | And Configure L2 tag rewrite method on interface | ${dut2_node} +| | ... | ${vlan2_index} | pop-1 +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1_node} | ${dut1_to_dut2} | ${vlan1_index} +| | ... | ${dut2_node} | ${dut2_to_tg} | ${vlan2_index} +| | Then Run Keyword And Expect Error | ICMP echo Rx timeout +| | ... | Send ICMP packet and verify received packet | ${tg_node} | ${tg_to_dut1} +| | ... | ${tg_to_dut2} | src_ip=${src_ip} | dst_ip=${dst_ip} | encaps=Dot1q +| | ... | vlan1=${outer_vlan_id1} |