diff options
Diffstat (limited to 'tests/vpp/perf/container_memif/10ge2p1x520-eth-l2xcbase-eth-1memif-1dcr-mrr.robot')
| -rw-r--r-- | tests/vpp/perf/container_memif/10ge2p1x520-eth-l2xcbase-eth-1memif-1dcr-mrr.robot | 440 |
1 files changed, 220 insertions, 220 deletions
diff --git a/tests/vpp/perf/container_memif/10ge2p1x520-eth-l2xcbase-eth-1memif-1dcr-mrr.robot b/tests/vpp/perf/container_memif/10ge2p1x520-eth-l2xcbase-eth-1memif-1dcr-mrr.robot index d0c70f0c6d..d9dcce584e 100644 --- a/tests/vpp/perf/container_memif/10ge2p1x520-eth-l2xcbase-eth-1memif-1dcr-mrr.robot +++ b/tests/vpp/perf/container_memif/10ge2p1x520-eth-l2xcbase-eth-1memif-1dcr-mrr.robot @@ -1,220 +1,220 @@ -# Copyright (c) 2018 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-# http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Settings ***
-| Resource | resources/libraries/robot/performance/performance_setup.robot
-| ...
-| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
-| ... | NIC_Intel-X520-DA2 | ETH | L2XCFWD | BASE | MEMIF | SINGLE_MEMIF
-| ... | DOCKER
-| ...
-| Suite Setup | Run Keywords
-| ... | Set up 3-node performance topology with DUT's NIC model | L2
-| ... | Intel-X520-DA2
-| ... | AND | Set up performance test suite with MEMIF
-| ... | AND | Set up performance topology with containers
-| ...
-| Suite Teardown | Tear down 3-node performance topology with container
-| ...
-| Test Setup | Run Keywords
-| ... | Set up performance test
-| ... | AND | Restart VPP in all 'VNF' containers
-| ...
-| Test Teardown | Tear down performance mrr test
-| ...
-| Test Template | Check RR for l2xcbase-eth-1memif-1dcr
-| ...
-| Documentation | *Raw results L2XC test cases*
-| ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
-| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 configured with L2 cross-
-| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
-| ... | Container is connected to VPP via Memif interface running same VPP
-| ... | version as running on DUT. Resources are limited via cgroup to use 5
-| ... | cores allocated from pool of isolated CPUs. There are no memory
-| ... | contraints. Cross Horizontal topology with packets flowing via DUT (VPP)
-| ... | to Container, then via horizontal memif to the next Container, and so on
-| ... | until the last Container then to NIC (in last Container). Single
-| ... | Container is supported as of now.
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
-| ... | addresses of the TG node interfaces.
-
-*** Variables ***
-# X520-DA2 bandwidth limit
-| ${s_limit} | ${10000000000}
-# Traffic profile
-| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254
-# Container settings
-| ${container_count}= | ${1}
-| ${container_engine}= | Docker
-| ${container_image}= | ubuntu:xenial-20180412
-| ${container_install_dkms}= | ${TRUE}
-| ${container_chain_topology}= | cross_horiz
-# CPU settings
-| ${system_cpus}= | ${1}
-| ${vpp_cpus}= | ${5}
-| ${container_cpus}= | ${5}
-
-*** Keywords ***
-| Check RR for l2xcbase-eth-1memif-1dcr
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2XC switching config with ${wt} thread(s), ${wt}\
-| | ... | phy core(s), ${rxq} receive queue(s) per NIC port.
-| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\
-| | ... | trial throughput test.
-| | ...
-| | [Arguments] | ${framesize} | ${wt} | ${rxq}
-| | ...
-| | Set Test Variable | ${framesize}
-| | ${get_framesize}= | Get Frame Size | ${framesize}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize}
-| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
-| | And Add single PCI device to all DUTs
-| | And Run Keyword If | ${get_framesize} < ${1522}
-| | ... | Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | And Initialize L2 xconnect for single memif in 3-node circular topology
-| | ... | ${rxq}
-| | Then Traffic should pass with maximum rate | ${perf_trial_duration}
-| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
-
-*** Test Cases ***
-| tc01-64B-1t1c-eth-l2xcbase-eth-1memif-1dcr-mrr
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2XC switching config with 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\
-| | ... | throughput test.
-| | ...
-| | [Tags] | 64B | 1C | THIS
-| | framesize=${64} | wt=1 | rxq=1
-
-| tc02-1518B-1t1c-eth-l2xcbase-eth-1memif-1dcr-mrr
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2XC switching config with 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\
-| | ... | throughput test.
-| | ...
-| | [Tags] | 1518B | 1C
-| | framesize=${1518} | wt=1 | rxq=1
-
-| tc03-9000B-1t1c-eth-l2xcbase-eth-1memif-1dcr-mrr
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2XC switching config with 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\
-| | ... | throughput test.
-| | ...
-| | [Tags] | 9000B | 1C
-| | framesize=${9000} | wt=1 | rxq=1
-
-| tc04-IMIX-1t1c-eth-l2xcbase-eth-1memif-1dcr-mrr
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2XC switching config with 1 phy core,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\
-| | ... | throughput test.
-| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B)
-| | ...
-| | [Tags] | IMIX | 1C
-| | framesize=IMIX_v4_1 | wt=1 | rxq=1
-
-| tc05-64B-2t2c-eth-l2xcbase-eth-1memif-1dcr-mrr
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2XC switching config with 2 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\
-| | ... | throughput test.
-| | ...
-| | [Tags] | 64B | 2C
-| | framesize=${64} | wt=2 | rxq=1
-
-| tc06-1518B-2t2c-eth-l2xcbase-eth-1memif-1dcr-mrr
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2XC switching config with 1 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\
-| | ... | throughput test.
-| | ...
-| | [Tags] | 1518B | 2C
-| | framesize=${1518} | wt=2 | rxq=1
-
-| tc07-9000B-2t2c-eth-l2xcbase-eth-1memif-1dcr-mrr
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2XC switching config with 1 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\
-| | ... | throughput test.
-| | ...
-| | [Tags] | 9000B | 2C
-| | framesize=${9000} | wt=2 | rxq=1
-
-| tc08-IMIX-2t2c-eth-l2xcbase-eth-1memif-1dcr-mrr
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2XC switching config with 2 phy cores,\
-| | ... | 1 receive queue per NIC port.
-| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\
-| | ... | throughput test.
-| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B)
-| | ...
-| | [Tags] | IMIX | 2C
-| | framesize=IMIX_v4_1 | wt=2 | rxq=1
-
-| tc09-64B-4t4c-eth-l2xcbase-eth-1memif-1dcr-mrr
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2XC switching config with 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\
-| | ... | throughput test.
-| | ...
-| | [Tags] | 64B | 4C
-| | framesize=${64} | wt=4 | rxq=2
-
-| tc10-1518B-4t4c-eth-l2xcbase-eth-1memif-1dcr-mrr
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2XC switching config with 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\
-| | ... | throughput test.
-| | ...
-| | [Tags] | 1518B | 4C
-| | framesize=${1518} | wt=4 | rxq=2
-
-| tc11-9000B-4t4c-eth-l2xcbase-eth-1memif-1dcr-mrr
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2XC switching config with 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\
-| | ... | throughput test.
-| | ...
-| | [Tags] | 9000B | 4C
-| | framesize=${9000} | wt=4 | rxq=2
-
-| tc12-IMIX-4t4c-eth-l2xcbase-eth-1memif-1dcr-mrr
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2XC switching config with 4 phy cores,\
-| | ... | 2 receive queues per NIC port.
-| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\
-| | ... | throughput test.
-| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B)
-| | ...
-| | [Tags] | IMIX | 4C
-| | framesize=IMIX_v4_1 | wt=4 | rxq=2
+# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | ETH | L2XCFWD | BASE | MEMIF | SINGLE_MEMIF +| ... | DOCKER +| ... +| Suite Setup | Run Keywords +| ... | Set up 3-node performance topology with DUT's NIC model | L2 +| ... | Intel-X520-DA2 +| ... | AND | Set up performance test suite with MEMIF +| ... | AND | Set up performance topology with containers +| ... +| Suite Teardown | Tear down 3-node performance topology with container +| ... +| Test Setup | Run Keywords +| ... | Set up performance test +| ... | AND | Restart VPP in all 'VNF' containers +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Check RR for l2xcbase-eth-1memif-1dcr +| ... +| Documentation | *Raw results L2XC test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 configured with L2 cross- +| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | Container is connected to VPP via Memif interface running same VPP +| ... | version as running on DUT. Resources are limited via cgroup to use 5 +| ... | cores allocated from pool of isolated CPUs. There are no memory +| ... | contraints. Cross Horizontal topology with packets flowing via DUT (VPP) +| ... | to Container, then via horizontal memif to the next Container, and so on +| ... | until the last Container then to NIC (in last Container). Single +| ... | Container is supported as of now. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 +# Container settings +| ${container_count}= | ${1} +| ${container_engine}= | Docker +| ${container_image}= | ubuntu:xenial-20180412 +| ${container_install_dkms}= | ${TRUE} +| ${container_chain_topology}= | cross_horiz +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${container_cpus}= | ${5} + +*** Keywords *** +| Check RR for l2xcbase-eth-1memif-1dcr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with ${wt} thread(s), ${wt}\ +| | ... | phy core(s), ${rxq} receive queue(s) per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${framesize} | ${wt} | ${rxq} +| | ... +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${get_framesize} +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add single PCI device to all DUTs +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect for single memif in 3-node circular topology +| | ... | ${rxq} +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2xcbase-eth-1memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 1C +| | framesize=${64} | wt=1 | rxq=1 + +| tc02-1518B-1t1c-eth-l2xcbase-eth-1memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 1C +| | framesize=${1518} | wt=1 | rxq=1 + +| tc03-9000B-1t1c-eth-l2xcbase-eth-1memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 9000B | 1C +| | framesize=${9000} | wt=1 | rxq=1 + +| tc04-IMIX-1t1c-eth-l2xcbase-eth-1memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | ... +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | wt=1 | rxq=1 + +| tc05-64B-2t2c-eth-l2xcbase-eth-1memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 2C +| | framesize=${64} | wt=2 | rxq=1 + +| tc06-1518B-2t2c-eth-l2xcbase-eth-1memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 2C +| | framesize=${1518} | wt=2 | rxq=1 + +| tc07-9000B-2t2c-eth-l2xcbase-eth-1memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 9000B | 2C +| | framesize=${9000} | wt=2 | rxq=1 + +| tc08-IMIX-2t2c-eth-l2xcbase-eth-1memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | ... +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | wt=2 | rxq=1 + +| tc09-64B-4t4c-eth-l2xcbase-eth-1memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 4C +| | framesize=${64} | wt=4 | rxq=2 + +| tc10-1518B-4t4c-eth-l2xcbase-eth-1memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 4C +| | framesize=${1518} | wt=4 | rxq=2 + +| tc11-9000B-4t4c-eth-l2xcbase-eth-1memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 9000B | 4C +| | framesize=${9000} | wt=4 | rxq=2 + +| tc12-IMIX-4t4c-eth-l2xcbase-eth-1memif-1dcr-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | ... +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | wt=4 | rxq=2 |