aboutsummaryrefslogtreecommitdiffstats
path: root/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr.robot
diff options
context:
space:
mode:
Diffstat (limited to 'tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr.robot')
-rw-r--r--tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr.robot209
1 files changed, 209 insertions, 0 deletions
diff --git a/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr.robot b/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr.robot
new file mode 100644
index 0000000000..68f11b84d2
--- /dev/null
+++ b/tests/vpp/perf/crypto/40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr.robot
@@ -0,0 +1,209 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/crypto/ipsec.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | IP4FWD | IPSEC | IPSECHW | IPSECTUN | NIC_Intel-XL710 | BASE
+| ...
+| Suite Setup | Set up IPSec performance test suite | L3 | Intel-XL710
+| ... | HW_cryptodev
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| Test Teardown | Tear down performance mrr test
+| ...
+| Documentation | *Raw results IPv4 IPsec tunnel mode performance test suite.*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 on TG-DUTn,
+| ... | Eth-IPv4-IPSec on DUT1-DUT2
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with multiple
+| ... | IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it
+| ... | and send to another DUT, where packets are decrypted and sent back to TG
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
+| ... | at line rate and reports total received/sent packets over trial period.
+| ... | Test packets are generated by TG on
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
+| ... | (flow-group per direction, number of flows per flow-group equals to
+| ... | number of IPSec tunnels) with all packets
+| ... | containing Ethernet header, IPv4 header with IP protocol=61 and
+| ... | static payload. MAC addresses are matching MAC addresses of the TG
+| ... | node interfaces. Incrementing of IP.dst (IPv4 destination address) field
+| ... | is applied to both streams.
+| ... | *[Ref] Applicable standard specifications:* RFC4303 and RFC2544.
+
+*** Variables ***
+# XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G}= | ${24500000000}
+# XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps}= | ${18750000}
+| ${tg_if1_ip4}= | 192.168.10.2
+| ${dut1_if1_ip4}= | 192.168.10.1
+| ${dut1_if2_ip4}= | 172.168.1.1
+| ${dut2_if1_ip4}= | 172.168.1.2
+| ${dut2_if2_ip4}= | 192.168.20.1
+| ${tg_if2_ip4}= | 192.168.20.2
+| ${raddr_ip4}= | 20.0.0.0
+| ${laddr_ip4}= | 10.0.0.0
+| ${addr_range}= | ${32}
+| ${ipsec_overhead}= | ${58}
+| ${n_tunnels}= | ${1}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-ethip4-ip4dst${n_tunnels}
+
+*** Keywords ***
+| Check RR for IPv4 routing with IPSec HW cryptodev
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPSec tunneling CBC-SHA1 config with ${wt} thread(s),\
+| | ... | ${wt} phy core(s), ${rxq} receive queue(s) per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\
+| | ... | trial throughput test.
+| | ...
+| | [Arguments] | ${framesize} | ${wt} | ${rxq}
+| | ...
+| | # Test Variables required for test teardown
+| | Set Test Variable | ${framesize}
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | ${max_rate}= | Calculate pps | ${s_24.5G}
+| | ... | ${get_framesize} + ${ipsec_overhead}
+| | ${max_rate}= | Set Variable If
+| | ... | ${max_rate} > ${s_18.75Mpps} | ${s_18.75Mpps} | ${max_rate}
+| | ${encr_alg}= | Crypto Alg AES CBC 128
+| | ${auth_alg}= | Integ Alg SHA1 96
+| | ...
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | And Run Keyword If | ${get_framesize} < ${1522}
+| | ... | Add no multi seg to all DUTs
+| | And Add cryptodev to all DUTs | ${${wt}}
+| | And Add DPDK dev default RXD to all DUTs | 2048
+| | And Add DPDK dev default TXD to all DUTs | 2048
+| | And Apply startup configuration on all VPP DUTs
+| | When Generate keys for IPSec | ${encr_alg} | ${auth_alg}
+| | And Initialize IPSec in 3-node circular topology
+| | And VPP IPsec Create Tunnel Interfaces
+| | ... | ${dut1} | ${dut2} | ${dut1_if2_ip4} | ${dut2_if1_ip4} | ${dut1_if2}
+| | ... | ${dut2_if1} | ${n_tunnels} | ${encr_alg} | ${encr_key} | ${auth_alg}
+| | ... | ${auth_key} | ${laddr_ip4} | ${raddr_ip4} | ${addr_range}
+| | Then Traffic should pass with maximum rate | ${perf_trial_duration}
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1t1c-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr
+| | [Documentation]
+| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\
+| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\
+| | ... | throughput test.
+| | [Tags] | 64B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for IPv4 routing with IPSec HW cryptodev
+| | framesize=${64} | wt=1 | rxq=1
+
+| tc02-1518B-1t1c-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr
+| | [Documentation]
+| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\
+| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single\
+| | ... | trial throughput test.
+| | [Tags] | 1518B | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for IPv4 routing with IPSec HW cryptodev
+| | framesize=${1518} | wt=1 | rxq=1
+
+# TODO: Add check to make test fail if rx=0.
+# TODO: Add 9000B test cases when they start passing.
+
+| tc04-IMIX-1t1c-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr
+| | [Documentation]
+| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\
+| | ... | with 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single\
+| | ... | trial throughput test.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | [Tags] | IMIX | 1T1C | STHREAD
+| | ...
+| | [Template] | Check RR for IPv4 routing with IPSec HW cryptodev
+| | framesize=IMIX_v4_1 | wt=1 | rxq=1
+
+| tc05-64B-2t2c-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr
+| | [Documentation]
+| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\
+| | ... | with 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\
+| | ... | throughput test.
+| | [Tags] | 64B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for IPv4 routing with IPSec HW cryptodev
+| | framesize=${64} | wt=2 | rxq=1
+
+| tc06-1518B-2t2c-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr
+| | [Documentation]
+| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\
+| | ... | with 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single\
+| | ... | trial throughput test.
+| | [Tags] | 1518B | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for IPv4 routing with IPSec HW cryptodev
+| | framesize=${1518} | wt=2 | rxq=1
+
+| tc08-IMIX-2t2c-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr
+| | [Documentation]
+| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\
+| | ... | with 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single\
+| | ... | trial throughput test.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | [Tags] | IMIX | 2T2C | MTHREAD
+| | ...
+| | [Template] | Check RR for IPv4 routing with IPSec HW cryptodev
+| | framesize=IMIX_v4_1 | wt=2 | rxq=1
+
+| tc09-64B-4t4c-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr
+| | [Documentation]
+| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\
+| | ... | with 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\
+| | ... | throughput test.
+| | [Tags] | 64B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for IPv4 routing with IPSec HW cryptodev
+| | framesize=${64} | wt=4 | rxq=2
+
+| tc10-1518B-4t4c-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr
+| | [Documentation]
+| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\
+| | ... | with 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single\
+| | ... | trial throughput test.
+| | [Tags] | 1518B | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for IPv4 routing with IPSec HW cryptodev
+| | framesize=${1518} | wt=4 | rxq=2
+
+| tc12-IMIX-4t4c-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr
+| | [Documentation]
+| | ... | [Cfg] DUTs run 1 IPsec tunnel CBC-SHA1 in each direction, configured\
+| | ... | with 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single\
+| | ... | trial throughput test.
+| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
+| | [Tags] | IMIX | 4T4C | MTHREAD
+| | ...
+| | [Template] | Check RR for IPv4 routing with IPSec HW cryptodev
+| | framesize=IMIX_v4_1 | wt=4 | rxq=2