diff options
Diffstat (limited to 'tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4base-iacl1sl-10kflows-mrr.robot')
| -rw-r--r-- | tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4base-iacl1sl-10kflows-mrr.robot | 243 |
1 files changed, 243 insertions, 0 deletions
diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4base-iacl1sl-10kflows-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4base-iacl1sl-10kflows-mrr.robot new file mode 100644 index 0000000000..32f9fac4d2 --- /dev/null +++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4base-iacl1sl-10kflows-mrr.robot @@ -0,0 +1,243 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | ETH | IP4FWD | FEATURE | ACL | ACL_STATELESS +| ... | IACL | ACL1 | 10k_FLOWS +| ... +| Suite Setup | Run Keywords +| ... | Set up 3-node performance topology with DUT's NIC model | L3 +| ... | Intel-X520-DA2 +| ... | AND | Set up performance test suite with ACL +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Documentation | *Raw results IPv4 test cases with ACL* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\ +| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\ +| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\ +| ... | DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.\ +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} + +# ACL test setup +| ${acl_action}= | permit +| ${acl_apply_type}= | input +| ${no_hit_aces_number}= | 1 +| ${flows_per_dir}= | 10k + +# starting points for non-hitting ACLs +| ${src_ip_start}= | 30.30.30.1 +| ${dst_ip_start}= | 40.40.40.1 +| ${ip_step}= | ${1} +| ${sport_start}= | ${1000} +| ${dport_start}= | ${1000} +| ${port_step}= | ${1} +| ${trex_stream1_subnet}= | 10.10.10.0/24 +| ${trex_stream2_subnet}= | 20.20.20.0/24 + +*** Keywords *** +| Check RR for IPv4 routing with ACLs +| | ... +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ACL with ${wt} thread(s),\ +| | ... | ${wt} phy core(s), ${rxq} receive queue(s) per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${wt} | ${rxq} | ${framesize} +| | ... +| | # Test Variables required for test execution and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | ${ip_nr}= | Set Variable | 10 +| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology +| | ${traffic_profile}= | Set Variable | trex-sl-3n-ethip4udp-10u1000p-conc +| | Set Test Variable | ${traffic_profile} +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4udp-ip4base-iacl1-stateless-flows10k-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for IPv4 routing with ACLs +| | wt=1 | rxq=1 | framesize=${64} + +| tc02-1518B-1t1c-ethip4udp-ip4base-iacl1-stateless-flows10k-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for IPv4 routing with ACLs +| | wt=1 | rxq=1 | framesize=${1518} + +| tc03-9000B-1t1c-ethip4udp-ip4base-iacl1-stateless-flows10k-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 9000B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for IPv4 routing with ACLs +| | wt=1 | rxq=1 | framesize=${9000} + +| tc04-IMIX-1t1c-ethip4udp-ip4base-iacl1-stateless-flows10k-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for IPv4 routing with ACLs +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 + +| tc05-64B-2t2c-ethip4udp-ip4base-iacl1-stateless-flows10k-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for IPv4 routing with ACLs +| | wt=2 | rxq=1 | framesize=${64} + +| tc06-1518B-2t2c-ethip4udp-ip4base-iacl1-stateless-flows10k-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for IPv4 routing with ACLs +| | wt=2 | rxq=1 | framesize=${1518} + +| tc07-9000B-2t2c-ethip4udp-ip4base-iacl1-stateless-flows10k-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for IPv4 routing with ACLs +| | wt=2 | rxq=1 | framesize=${9000} + +| tc08-IMIX-2t2c-ethip4udp-ip4base-iacl1-stateless-flows10k-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for IPv4 routing with ACLs +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 + +| tc09-64B-4t4c-ethip4udp-ip4base-iacl1-stateless-flows10k-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for IPv4 routing with ACLs +| | wt=4 | rxq=2 | framesize=${64} + +| tc10-1518B-4t4c-ethip4udp-ip4base-iacl1-stateless-flows10k-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for IPv4 routing with ACLs +| | wt=4 | rxq=2 | framesize=${1518} + +| tc11-9000B-4t4c-ethip4udp-ip4base-iacl1-stateless-flows10k-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for IPv4 routing with ACLs +| | wt=4 | rxq=2 | framesize=${9000} + +| tc12-IMIX-4t4c-ethip4udp-ip4base-iacl1-stateless-flows10k-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with ACL with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for IPv4 routing with ACLs +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 |