1 files changed, 0 insertions, 147 deletions
diff --git a/tests/vpp/perf/ip4/10ge2p1x710-ethip4udp-ip4base-iacl50sf-10kflows-mrr.robot b/tests/vpp/perf/ip4/10ge2p1x710-ethip4udp-ip4base-iacl50sf-10kflows-mrr.robot
deleted file mode 100644
index 9d3debccd3..0000000000
--- a/tests/vpp/perf/ip4/10ge2p1x710-ethip4udp-ip4base-iacl50sf-10kflows-mrr.robot
+++ /dev/null
@@ -1,147 +0,0 @@
-# Copyright (c) 2018 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-#     http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Settings ***
-| Resource | resources/libraries/robot/performance/performance_setup.robot
-| ...
-| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
-| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATEFUL
-| ... | IACL | ACL50 | 10k_FLOWS
-| ...
-| Suite Setup | Run Keywords
-| ... | Set up 3-node performance topology with DUT's NIC model | L3
-| ... | Intel-X710
-| ... | AND | Set up performance test suite with ACL
-| Suite Teardown | Tear down 3-node performance topology
-| ...
-| Test Setup | Set up performance test
-| ...
-| Test Teardown | Tear down performance mrr test
-| ...
-| Test Template | Local Template
-| ...
-| Documentation | *Raw results IPv4 test cases with ACL*
-| ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
-| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
-| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
-| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X710 Niantic by Intel.
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
-| ... | at line rate and reports total received/sent packets over trial period.\
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
-| ... | header with IP protocol=61 and static payload. MAC addresses are\
-| ... | matching MAC addresses of the TG node interfaces.
-| ... | *[Ref] Applicable standard specifications:* RFC2544.
-
-*** Variables ***
-# X710 bandwidth limit
-| ${s_limit}= | ${10000000000}
-
-# ACL test setup
-| ${acl_action}= | permit+reflect
-| ${acl_apply_type}= | input
-| ${no_hit_aces_number}= | 50
-| ${flows_per_dir}= | 10k
-
-# starting points for non-hitting ACLs
-| ${src_ip_start}= | 30.30.30.1
-| ${dst_ip_start}= | 40.40.40.1
-| ${ip_step}= | ${1}
-| ${sport_start}= | ${1000}
-| ${dport_start}= | ${1000}
-| ${port_step}= | ${1}
-| ${trex_stream1_subnet}= | 10.10.10.0/24
-| ${trex_stream2_subnet}= | 20.20.20.0/24
-
-| ${traffic_profile}= | trex-sl-3n-ethip4udp-10u1000p-conc
-
-*** Keywords ***
-| Local Template
-| | ...
-| | [Documentation]
-| | ... | [Cfg] DUT runs IPv4 routing config.
-| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
-| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
-| | ... | trial throughput test.
-| | ...
-| | ... | *Arguments:*
-| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
-| | ... | Type: integer, string
-| | ... | - phy_cores - Number of physical cores. Type: integer
-| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
-| | ...
-| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
-| | ...
-| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
-| | And Add PCI devices to all DUTs
-| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
-| | ... | ${s_limit} | ${framesize}
-| | And Apply startup configuration on all VPP DUTs
-| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
-| | Then Traffic should pass with maximum rate
-| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
-
-*** Test Cases ***
-| tc01-64B-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
-| | [Tags] | 64B | 1C
-| | framesize=${64} | phy_cores=${1}
-
-| tc02-64B-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
-| | [Tags] | 64B | 2C
-| | framesize=${64} | phy_cores=${2}
-
-| tc03-64B-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
-| | [Tags] | 64B | 4C
-| | framesize=${64} | phy_cores=${4}
-
-| tc04-1518B-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
-| | [Tags] | 1518B | 1C
-| | framesize=${1518} | phy_cores=${1}
-
-| tc05-1518B-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
-| | [Tags] | 1518B | 2C
-| | framesize=${1518} | phy_cores=${2}
-
-| tc06-1518B-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
-| | [Tags] | 1518B | 4C
-| | framesize=${1518} | phy_cores=${4}
-
-| tc07-9000B-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
-| | [Tags] | 9000B | 1C
-| | framesize=${9000} | phy_cores=${1}
-
-| tc08-9000B-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
-| | [Tags] | 9000B | 2C
-| | framesize=${9000} | phy_cores=${2}
-
-| tc09-9000B-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
-| | [Tags] | 9000B | 4C
-| | framesize=${9000} | phy_cores=${4}
-
-| tc10-IMIX-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
-| | [Tags] | IMIX | 1C
-| | framesize=IMIX_v4_1 | phy_cores=${1}
-
-| tc11-IMIX-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
-| | [Tags] | IMIX | 2C
-| | framesize=IMIX_v4_1 | phy_cores=${2}
-
-| tc12-IMIX-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
-| | [Tags] | IMIX | 4C
-| | framesize=IMIX_v4_1 | phy_cores=${4}