1 files changed, 132 insertions, 0 deletions
diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr.robot
new file mode 100644
index 0000000000..4c517df0c6
--- /dev/null
+++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr.robot
@@ -0,0 +1,132 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X520-DA2 | L2BDMACLRN | SCALE | L2BD_100 | DOT1Q | VLAN_100
+| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_100
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L2 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results L2BD with IEEE 802.1Q and VXLANoIPv4 test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\
+| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 100 L2\
+| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\
+| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\
+| ... | flows per flow-group) with all packets containing Ethernet header,\
+| ... | IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload.\
+| ... | MAC addresses are matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348.
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${overhead}= | ${50}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan100ip4src254ip4dst254
+# Number of VXLAN tunnels
+| ${vxlan_count}= | ${100}
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\
+| | ... | uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize} | overhead=${overhead}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology
+| | ... | vxlan_count=${vxlan_count}
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}