diff options
Diffstat (limited to 'tests/vpp/perf/ip4_tunnels')
3 files changed, 697 insertions, 0 deletions
diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4lispip4-ip4base-mrr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4lispip4-ip4base-mrr.robot new file mode 100644 index 0000000000..d917e3926e --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4lispip4-ip4base-mrr.robot @@ -0,0 +1,247 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Resource | resources/libraries/robot/overlay/lisp_static_adjacency.robot +| Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | IP4FWD | ENCAP | LISP | IP4UNRLAY | IP4OVRLAY +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Documentation | *Raw results Lisp test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISP-IPv4 on DUT1-DUT2,\ +| ... | Eth-IPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\ +| ... | routing and static routes. LISPoIPv4 tunnel is configured between DUT1\ +| ... | and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC6830. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${lisp_overhead}= | ${8} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src253 + +*** Keywords *** +| Check RR for ethip4lispip4-ip4base +| | ... +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters\ +| | ... | config with ${wt} thread(s), ${wt} phy core(s), ${rxq} receive\ +| | ... | queue(s) per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${wt} | ${rxq} | ${framesize} +| | ... +| | # Test Variables required for test execution and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} +| | ... | ${get_framesize + ${lisp_overhead}} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize + ${lisp_overhead}} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize LISP IPv4 forwarding in 3-node circular topology +| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4} +| | ... | ${dut2_to_tg_ip4} | ${prefix4} +| | And Configure LISP topology in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${NONE} +| | ... | ${dut2} | ${dut2_if1} | ${NONE} +| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid} +| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency} +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4lispip4-ip4base-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist\ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\ +| | ... | port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4lispip4-ip4base +| | wt=1 | rxq=1 | framesize=${64} + +| tc02-1480B-1t1c-ethip4lispip4-ip4base-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist\ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\ +| | ... | port. +| | ... | [Ver] Measure MaxReceivedRate for 1480B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1480B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4lispip4-ip4base +| | wt=1 | rxq=1 | framesize=${1480} + +| tc03-9000B-1t1c-ethip4lispip4-ip4base-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist\ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\ +| | ... | port. +| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 9000B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4lispip4-ip4base +| | wt=1 | rxq=1 | framesize=${9000} + +| tc04-IMIX-1t1c-ethip4lispip4-ip4base-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist\ +| | ... | filters config with 1 thread, 1 phy core, 1 receive queue per NIC\ +| | ... | port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4lispip4-ip4base +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 + +| tc05-64B-2t2c-ethip4lispip4-ip4base-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist\ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\ +| | ... | port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 2T2C | STHREAD +| | ... +| | [Template] | Check RR for ethip4lispip4-ip4base +| | wt=2 | rxq=1 | framesize=${64} + +| tc06-1480B-2t2c-ethip4lispip4-ip4base-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist\ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\ +| | ... | port. +| | ... | [Ver] Measure MaxReceivedRate for 1480B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1480B | 2T2C | STHREAD +| | ... +| | [Template] | Check RR for ethip4lispip4-ip4base +| | wt=2 | rxq=1 | framesize=${1480} + +| tc07-9000B-2t2c-ethip4lispip4-ip4base-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist\ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\ +| | ... | port. +| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 9000B | 2T2C | STHREAD +| | ... +| | [Template] | Check RR for ethip4lispip4-ip4base +| | wt=2 | rxq=1 | framesize=${9000} + +| tc08-IMIX-2t2c-ethip4lispip4-ip4base-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist\ +| | ... | filters config with 2 threads, 2 phy cores, 1 receive queue per NIC\ +| | ... | port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 2T2C | STHREAD +| | ... +| | [Template] | Check RR for ethip4lispip4-ip4base +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 + +| tc09-64B-4t4c-ethip4lispip4-ip4base-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist\ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\ +| | ... | port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 4T4C | STHREAD +| | ... +| | [Template] | Check RR for ethip4lispip4-ip4base +| | wt=4 | rxq=2 | framesize=${64} + +| tc10-1480B-4t4c-ethip4lispip4-ip4base-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist\ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\ +| | ... | port. +| | ... | [Ver] Measure MaxReceivedRate for 1480B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1480B | 4T4C | STHREAD +| | ... +| | [Template] | Check RR for ethip4lispip4-ip4base +| | wt=4 | rxq=2 | framesize=${1480} + +| tc11-9000B-4t4c-ethip4lispip4-ip4base-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist\ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\ +| | ... | port. +| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 9000B | 4T4C | STHREAD +| | ... +| | [Template] | Check RR for ethip4lispip4-ip4base +| | wt=4 | rxq=2 | framesize=${9000} + +| tc12-IMIX-4t4c-ethip4lispip4-ip4base-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 LISP remote static mappings and whitelist\ +| | ... | filters config with 4 threads, 4 phy cores, 2 receive queues per NIC\ +| | ... | port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 4T4C | STHREAD +| | ... +| | [Template] | Check RR for ethip4lispip4-ip4base +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-mrr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-mrr.robot new file mode 100644 index 0000000000..cce962f65c --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-mrr.robot @@ -0,0 +1,225 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Documentation | *Raw results L2BD with VXLANoIPv4 test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain on TG-DUTn. +| ... | Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge +| ... | domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. +| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${vxlan_overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check RR for ethip4vxlan-l2bdbasemaclrn +| | ... +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD forwarding config with ${wt} thread(s), ${wt}\ +| | ... | phy core(s), ${rxq} receive queue(s) per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${wt} | ${rxq} | ${framesize} +| | ... +| | # Test Variables required for test execution and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} +| | ... | ${get_framesize + ${vxlan_overhead}} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize + ${vxlan_overhead}} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VXLANoIPv4 in 3-node circular topology +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4vxlan-l2bdbasemaclrn-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD forwarding config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn +| | wt=1 | rxq=1 | framesize=${64} + +| tc02-1518B-1t1c-ethip4vxlan-l2bdbasemaclrn-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD forwarding config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn +| | wt=1 | rxq=1 | framesize=${1518} + +| tc03-9000B-1t1c-ethip4vxlan-l2bdbasemaclrn-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD forwarding config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | ... +| | [Tags] | 9000B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn +| | wt=1 | rxq=1 | framesize=${9000} + +| tc04-IMIX-1t1c-ethip4vxlan-l2bdbasemaclrn-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD forwarding config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 + +| tc05-64B-2t2c-ethip4vxlan-l2bdbasemaclrn-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD forwarding config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn +| | wt=2 | rxq=1 | framesize=${64} + +| tc06-1518B-2t2c-ethip4vxlan-l2bdbasemaclrn-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD forwarding config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | SKIP_PATCH +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn +| | wt=2 | rxq=1 | framesize=${1518} + +| tc07-9000B-2t2c-ethip4vxlan-l2bdbasemaclrn-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD forwarding config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | ... +| | [Tags] | 9000B | 2T2C | MTHREAD | SKIP_PATCH +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn +| | wt=2 | rxq=1 | framesize=${9000} + +| tc08-IMIX-2t2c-ethip4vxlan-l2bdbasemaclrn-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD forwarding config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 + +| tc09-64B-4t4c-ethip4vxlan-l2bdbasemaclrn-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD forwarding config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn +| | wt=4 | rxq=2 | framesize=${64} + +| tc10-1518B-4t4c-ethip4vxlan-l2bdbasemaclrn-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD forwarding config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single\ +| | ... | trial throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | SKIP_PATCH +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn +| | wt=4 | rxq=2 | framesize=${1518} + +| tc11-9000B-4t4c-ethip4vxlan-l2bdbasemaclrn-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD forwarding config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | ... +| | [Tags] | 9000B | 4T4C | MTHREAD | SKIP_PATCH +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn +| | wt=4 | rxq=2 | framesize=${9000} + +| tc12-IMIX-4t4c-ethip4vxlan-l2bdbasemaclrn-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD forwarding config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2bdbasemaclrn +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4vxlan-l2xcbase-mrr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4vxlan-l2xcbase-mrr.robot new file mode 100644 index 0000000000..962c499f93 --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4vxlan-l2xcbase-mrr.robot @@ -0,0 +1,225 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | L2XCFWD | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Documentation | *Raw results L2XC with VXLANoIPv4 test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross-connect on TG-DUTn. +| ... | Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. VXLAN tunnels are configured between L2XCs on DUT1 and DUT2. +| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic +| ... | at line rate and reports total received/sent packets over trial period. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile +| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per +| ... | flow-group) with all packets containing Ethernet header, IPv4 header +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${vxlan_overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check RR for ethip4vxlan-l2xcbase +| | ... +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with ${wt} thread(s), ${wt}\ +| | ... | phy core(s), ${rxq} receive queue(s) per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\ +| | ... | trial throughput test. +| | ... +| | [Arguments] | ${wt} | ${rxq} | ${framesize} +| | ... +| | # Test Variables required for test execution and test teardown +| | Set Test Variable | ${framesize} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ${max_rate}= | Calculate pps | ${s_limit} +| | ... | ${get_framesize + ${vxlan_overhead}} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize + ${vxlan_overhead}} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 xconnect with VXLANoIPv4 in 3-node circular topology +| | Then Traffic should pass with maximum rate | ${perf_trial_duration} +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4vxlan-l2xcbase-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2xcbase +| | wt=1 | rxq=1 | framesize=${64} + +| tc02-1518B-1t1c-ethip4vxlan-l2xcbase-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2xcbase +| | wt=1 | rxq=1 | framesize=${1518} + +| tc03-9000B-1t1c-ethip4vxlan-l2xcbase-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 9000B | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2xcbase +| | wt=1 | rxq=1 | framesize=${9000} + +| tc04-IMIX-1t1c-ethip4vxlan-l2xcbase-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2xcbase +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 + +| tc05-64B-2t2c-ethip4vxlan-l2xcbase-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2xcbase +| | wt=2 | rxq=1 | framesize=${64} + +| tc06-1518B-2t2c-ethip4vxlan-l2xcbase-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2xcbase +| | wt=2 | rxq=1 | framesize=${1518} + +| tc07-9000B-2t2c-ethip4vxlan-l2xcbase-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2xcbase +| | wt=2 | rxq=1 | framesize=${9000} + +| tc08-IMIX-2t2c-ethip4vxlan-l2xcbase-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2xcbase +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 + +| tc09-64B-4t4c-ethip4vxlan-l2xcbase-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 64B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2xcbase +| | wt=4 | rxq=2 | framesize=${64} + +| tc10-1518B-4t4c-ethip4vxlan-l2xcbase-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 1518B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2xcbase +| | wt=4 | rxq=2 | framesize=${1518} + +| tc11-9000B-4t4c-ethip4vxlan-l2xcbase-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for 9000B frames using single trial\ +| | ... | throughput test. +| | ... +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2xcbase +| | wt=4 | rxq=2 | framesize=${9000} + +| tc12-IMIX-4t4c-ethip4vxlan-l2xcbase-mrr +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queue per NIC port. +| | ... | [Ver] Measure MaxReceivedRate for IMIX_v4_1 frames using single trial\ +| | ... | throughput test. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD +| | ... +| | [Template] | Check RR for ethip4vxlan-l2xcbase +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 |