diff options
Diffstat (limited to 'tests/vpp/perf/ip6/10ge2p1x520-dot1q-ip6base-ndrpdr.robot')
| -rw-r--r-- | tests/vpp/perf/ip6/10ge2p1x520-dot1q-ip6base-ndrpdr.robot | 138 |
1 files changed, 0 insertions, 138 deletions
diff --git a/tests/vpp/perf/ip6/10ge2p1x520-dot1q-ip6base-ndrpdr.robot b/tests/vpp/perf/ip6/10ge2p1x520-dot1q-ip6base-ndrpdr.robot deleted file mode 100644 index df54157524..0000000000 --- a/tests/vpp/perf/ip6/10ge2p1x520-dot1q-ip6base-ndrpdr.robot +++ /dev/null @@ -1,138 +0,0 @@ -# Copyright (c) 2018 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance/performance_setup.robot -| ... -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR -| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | BASE | DOT1Q | IP6BASE -| ... -| Suite Setup | Set up 3-node performance topology with DUT's NIC model -| ... | L3 | Intel-X520-DA2 -| Suite Teardown | Tear down 3-node performance topology -| ... -| Test Setup | Set up performance test -| Test Teardown | Tear down performance mrr test -| ... -| Test Template | Local Template -| ... -| Documentation | *RFC2544: Pkt throughput IPv6 routing with IEEE 802.1Q test -| ... | cases* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ -| ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. IEEE 802.1Q\ -| ... | tagging is applied on link between DUT1 and DUT2. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6\ -| ... | routing and two static IPv6 /64 route entries. DUT1 and DUT2 are tested\ -| ... | with 2p10GE NIC X520 Niantic by Intel. -| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ -| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ -| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ -| ... | of packets transmitted. NDR and PDR are discovered for different\ -| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\ -| ... | generated by TG on links to DUTs. TG traffic profile contains two L3\ -| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with\ -| ... | all packets containing Ethernet header, IPv6 header with IP\ -| ... | protocol=61 and static payload. MAC addresses are matching MAC\ -| ... | addresses of the TG node interfaces. -| ... | *[Ref] Applicable standard specifications:* RFC2544. - -*** Variables *** -| ${subid}= | 10 -| ${tag_rewrite}= | pop-1 -| ${overhead}= | ${4} -# X520-DA2 bandwidth limit -| ${s_limit}= | ${10000000000} -# TG subnets used by T-Rex -| ${tg_if1_net}= | 2001:1::0 -| ${tg_if2_net}= | 2001:2::0 -# Traffic profile: -| ${traffic_profile}= | trex-sl-3n-ethip6-ip6src253 - -*** Keywords *** -| Local Template -| | [Documentation] -| | ... | [Cfg] Each DUT runs IPv6 routing with VLAN and uses ${phy_cores}\ -| | ... | physical core(s) for worker threads. -| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. -| | ... -| | ... | *Arguments:* -| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). -| | ... | Type: integer, string -| | ... | - phy_cores - Number of physical cores. Type: integer -| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer -| | ... -| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} -| | ... -| | Set Test Variable | ${framesize} -| | Set Test Variable | ${min_rate} | ${10000} -| | ... -| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} -| | And Add PCI devices to all DUTs -| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg -| | ... | ${s_limit} | ${framesize} | overhead=${overhead} -| | And Apply startup configuration on all VPP DUTs -| | When Initialize IPv6 forwarding with VLAN dot1q sub-interfaces in circular topology -| | ... | ${tg_if1_net} | ${tg_if2_net} | ${subid} | ${tag_rewrite} -| | Then Find NDR and PDR intervals using optimized search -| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} - -*** Test Cases *** -| tc01-78B-1c-dot1q-ip6base-ndrpdr -| | [Tags] | 78B | 1C -| | framesize=${78} | phy_cores=${1} - -| tc02-78B-2c-dot1q-ip6base-ndrpdr -| | [Tags] | 78B | 2C -| | framesize=${78} | phy_cores=${2} - -| tc03-78B-4c-dot1q-ip6base-ndrpdr -| | [Tags] | 78B | 4C -| | framesize=${78} | phy_cores=${4} - -| tc04-1518B-1c-dot1q-ip6base-ndrpdr -| | [Tags] | 1518B | 1C -| | framesize=${1518} | phy_cores=${1} - -| tc05-1518B-2c-dot1q-ip6base-ndrpdr -| | [Tags] | 1518B | 2C -| | framesize=${1518} | phy_cores=${2} - -| tc06-1518B-4c-dot1q-ip6base-ndrpdr -| | [Tags] | 1518B | 4C -| | framesize=${1518} | phy_cores=${4} - -| tc07-9000B-1c-dot1q-ip6base-ndrpdr -| | [Tags] | 9000B | 1C -| | framesize=${9000} | phy_cores=${1} - -| tc08-9000B-2c-dot1q-ip6base-ndrpdr -| | [Tags] | 9000B | 2C -| | framesize=${9000} | phy_cores=${2} - -| tc09-9000B-4c-dot1q-ip6base-ndrpdr -| | [Tags] | 9000B | 4C -| | framesize=${9000} | phy_cores=${4} - -| tc10-IMIX-1c-dot1q-ip6base-ndrpdr -| | [Tags] | IMIX | 1C -| | framesize=IMIX_v4_1 | phy_cores=${1} - -| tc11-IMIX-2c-dot1q-ip6base-ndrpdr -| | [Tags] | IMIX | 2C -| | framesize=IMIX_v4_1 | phy_cores=${2} - -| tc12-IMIX-4c-dot1q-ip6base-ndrpdr -| | [Tags] | IMIX | 4C -| | framesize=IMIX_v4_1 | phy_cores=${4} |