diff options
Diffstat (limited to 'tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-iacldstbase-ndrpdrdisc.robot')
| -rw-r--r-- | tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-iacldstbase-ndrpdrdisc.robot | 474 |
1 files changed, 474 insertions, 0 deletions
diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-iacldstbase-ndrpdrdisc.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-iacldstbase-ndrpdrdisc.robot new file mode 100644 index 0000000000..6ee98fbcc4 --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-iacldstbase-ndrpdrdisc.robot @@ -0,0 +1,474 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.Classify.Classify +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | FEATURE | IACLDST +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput IPv6 iAcl whitelist test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing, two static IPv6 /64 routes and IPv6 iAcl security whitelist +| ... | ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. +| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 253 flows per flow-group) with all packets +| ... | containing Ethernet header, IPv6 header and generated payload. MAC +| ... | addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253 + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. +| | [Tags] | 78B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc02-78B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. +| | [Tags] | 78B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc03-1518B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc04-1518B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc05-9000B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. +| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc06-9000B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc07-78B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. +| | [Tags] | 78B | 2T2C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc08-78B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. +| | [Tags] | 78B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc09-1518B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc10-1518B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc11-9000B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. +| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc12-9000B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc13-78B-4t4c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. +| | [Tags] | 78B | 4T4C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc14-78B-4t4c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. +| | [Tags] | 78B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc15-1518B-4t4c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc16-1518B-4t4c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc17-9000B-4t4c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. +| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc18-9000B-4t4c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} |