diff options
Diffstat (limited to 'tests/vpp/perf/ip6')
15 files changed, 4666 insertions, 0 deletions
diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-copwhtlistbase-ndrchk.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-copwhtlistbase-ndrchk.robot new file mode 100644 index 0000000000..c619b6530b --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-copwhtlistbase-ndrchk.robot @@ -0,0 +1,256 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.Cop +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | FEATURE | COPWHLIST +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance ndrchk test +| ... +| Documentation | *Reference NDR throughput IPv6 whitelist verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing, two static IPv6 /64 routes and IPv6 COP security whitelist +| ... | ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. +| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT configuration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv6 header and static +| ... | payload. MAC addresses are matching MAC addresses of the TG node +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253 + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6base-copwhtlistbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 78 Byte frames using single trial throughput test +| | ... | at 2x 3.1mpps. +| | [Tags] | 78B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 3.1mpps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc02-1518B-1t1c-ethip6-ip6base-copwhtlistbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 1518 Byte frames using single trial throughput test +| | ... | at 2x 812743pps. +| | [Tags] | 1518B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc03-9000B-1t1c-ethip6-ip6base-copwhtlistbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 9000 Byte frames using single trial throughput test +| | ... | at 2x 138580pps. +| | [Tags] | 9000B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc04-78B-2t2c-ethip6-ip6base-copwhtlistbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 78 Byte frames using single trial throughput test +| | ... | at 2x 5.9mpps. +| | [Tags] | 78B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 5.9mpps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc05-1518B-2t2c-ethip6-ip6base-copwhtlistbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 1518 Byte frames using single trial throughput test +| | ... | at 2x 812743pps. +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc06-9000B-2t2c-ethip6-ip6base-copwhtlistbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 9000 Byte frames using single trial throughput test +| | ... | at 2x 138580pps. +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc07-78B-4t4c-ethip6-ip6base-copwhtlistbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 78 Byte frames using single trial throughput test +| | ... | at 2x 9.4mpps. +| | [Tags] | 78B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 9.4mpps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc08-1518B-4t4c-ethip6-ip6base-copwhtlistbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 1518 Byte frames using single trial throughput test +| | ... | at 2x 812743pps. +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc09-9000B-4t4c-ethip6-ip6base-copwhtlistbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 9000 Byte frames using single trial throughput test +| | ... | at 2x 138580pps. +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-copwhtlistbase-ndrpdrdisc.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-copwhtlistbase-ndrpdrdisc.robot new file mode 100644 index 0000000000..6808603262 --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-copwhtlistbase-ndrpdrdisc.robot @@ -0,0 +1,565 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.Cop +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | FEATURE | COPWHLIST +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput IPv6 whitelist test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing, two static IPv6 /64 routes and IPv6 COP security whitelist +| ... | ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. +| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 253 flows per flow-group) with all packets +| ... | containing Ethernet header, IPv6 header and static +| ... | payload. MAC addresses are matching MAC addresses of the TG node +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253 + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6base-copwhtlistbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. +| | [Tags] | 78B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc02-78B-1t1c-ethip6-ip6base-copwhtlistbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. +| | [Tags] | 78B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc03-1518B-1t1c-ethip6-ip6base-copwhtlistbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc04-1518B-1t1c-ethip6-ip6base-copwhtlistbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc05-9000B-1t1c-ethip6-ip6base-copwhtlistbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. +| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc06-9000B-1t1c-ethip6-ip6base-copwhtlistbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc07-78B-2t2c-ethip6-ip6base-copwhtlistbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. +| | [Tags] | 78B | 2T2C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc08-78B-2t2c-ethip6-ip6base-copwhtlistbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. +| | [Tags] | 78B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc09-1518B-2t2c-ethip6-ip6base-copwhtlistbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc10-1518B-2t2c-ethip6-ip6base-copwhtlistbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc11-9000B-2t2c-ethip6-ip6base-copwhtlistbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. +| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc12-9000B-2t2c-ethip6-ip6base-copwhtlistbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc13-78B-4t4c-ethip6-ip6base-copwhtlistbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. +| | [Tags] | 78B | 4T4C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc14-78B-4t4c-ethip6-ip6base-copwhtlistbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. +| | [Tags] | 78B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc15-1518B-4t4c-ethip6-ip6base-copwhtlistbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc16-1518B-4t4c-ethip6-ip6base-copwhtlistbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc17-9000B-4t4c-ethip6-ip6base-copwhtlistbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. +| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc18-9000B-4t4c-ethip6-ip6base-copwhtlistbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | When Initialize IPv6 forwarding in 3-node circular topology +| | And Add fib table | ${dut1} | 2001:1:: | 64 | 1 | local +| | And Add fib table | ${dut2} | 2001:2:: | 64 | 1 | local +| | And COP Add whitelist Entry | ${dut1} | ${dut1_if1} | ip6 | 1 +| | And COP Add whitelist Entry | ${dut2} | ${dut2_if2} | ip6 | 1 +| | And COP interface enable or disable | ${dut1} | ${dut1_if1} | enable +| | And COP interface enable or disable | ${dut2} | ${dut2_if2} | enable +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-iacldstbase-ndrchk.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-iacldstbase-ndrchk.robot new file mode 100644 index 0000000000..b82a356f1b --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-iacldstbase-ndrchk.robot @@ -0,0 +1,210 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.Classify.Classify +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | FEATURE | IACLDST +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance ndrchk test +| ... +| Documentation | *Reference NDR throughput IPv6 whitelist verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing, two static IPv6 /64 routes and IPv6 iAcl security whitelist +| ... | ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. +| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT confiiguration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv6 header and generated +| ... | payload. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253 + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6base-iacldstbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 78 Byte frames using single trial throughput test +| | ... | at 2x 3.2mpps. +| | [Tags] | 78B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 3.2mpps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc02-1518B-1t1c-ethip6-ip6base-iacldstbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 1518 Byte frames using single trial throughput test +| | ... | at 2x 812743pps. +| | [Tags] | 1518B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc03-9000B-1t1c-ethip6-ip6base-iacldstbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 9000 Byte frames using single trial throughput test +| | ... | at 2x 138580pps. +| | [Tags] | 9000B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc04-78B-2t2c-ethip6-ip6base-iacldstbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 78 Byte frames using single trial throughput test +| | ... | at 2x 5.7mpps. +| | [Tags] | 78B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 5.7mpps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc05-1518B-2t2c-ethip6-ip6base-iacldstbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 1518 Byte frames using single trial throughput test +| | ... | at 2x 812743pps. +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc06-9000B-2t2c-ethip6-ip6base-iacldstbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 9000 Byte frames using single trial throughput test +| | ... | at 2x 138580pps. +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc07-78B-4t4c-ethip6-ip6base-iacldstbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 78 Byte frames using single trial throughput test +| | ... | at 2x 9.2mpps. +| | [Tags] | 78B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 9.2mpps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc08-1518B-4t4c-ethip6-ip6base-iacldstbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 1518 Byte frames using single trial throughput test +| | ... | at 2x 812743pps. +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc09-9000B-4t4c-ethip6-ip6base-iacldstbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 thread, 4 phy core, 2 receive queue per NIC port. [Ver] Verify +| | ... | ref-NDR for 9000 Byte frames using single trial throughput test +| | ... | at 2x 138580pps. +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-iacldstbase-ndrpdrdisc.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-iacldstbase-ndrpdrdisc.robot new file mode 100644 index 0000000000..6ee98fbcc4 --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-iacldstbase-ndrpdrdisc.robot @@ -0,0 +1,474 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.Classify.Classify +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | FEATURE | IACLDST +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput IPv6 iAcl whitelist test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing, two static IPv6 /64 routes and IPv6 iAcl security whitelist +| ... | ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. +| ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 253 flows per flow-group) with all packets +| ... | containing Ethernet header, IPv6 header and generated payload. MAC +| ... | addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253 + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. +| | [Tags] | 78B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc02-78B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. +| | [Tags] | 78B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc03-1518B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc04-1518B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc05-9000B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. +| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc06-9000B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc07-78B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. +| | [Tags] | 78B | 2T2C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc08-78B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. +| | [Tags] | 78B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc09-1518B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc10-1518B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc11-9000B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. +| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc12-9000B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc13-78B-4t4c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps. +| | [Tags] | 78B | 4T4C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc14-78B-4t4c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 78 Byte frames using binary search start at 10GE linerate, +| | ... | step 100kpps, LT=0.5%. +| | [Tags] | 78B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc15-1518B-4t4c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps. +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc16-1518B-4t4c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 1518 Byte frames using binary search start at 10GE linerate, +| | ... | step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc17-9000B-4t4c-ethip6-ip6base-iacldstbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find NDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps. +| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc18-9000B-4t4c-ethip6-ip6base-iacldstbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing and whitelist filters config with \ +| | ... | 4 threads, 4 phy cores, 2 receive queue per NIC port. [Ver] Find PDR +| | ... | for 9000 Byte frames using binary search start at 10GE linerate, +| | ... | step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | And Initialize IPv6 iAcl whitelist in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-ndrchk.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-ndrchk.robot new file mode 100644 index 0000000000..8011baf632 --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-ndrchk.robot @@ -0,0 +1,191 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | BASE | IP6BASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance ndrchk test +| ... +| Documentation | *Reference NDR throughput IPv6 routing verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with +| ... | 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT configuration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv6 header and static +| ... | payload. MAC addresses are matching MAC addresses of the TG node +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253 + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6base-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test at 2x 3.9mpps. +| | [Tags] | 78B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 3.9mpps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc02-1518B-1t1c-ethip6-ip6base-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc03-9000B-1t1c-ethip6-ip6base-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc04-78B-2t2c-ethip6-ip6base-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test at 2x 8.1mpps. +| | [Tags] | 78B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 8.1mpps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc05-1518B-2t2c-ethip6-ip6base-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc06-9000B-2t2c-ethip6-ip6base-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc07-78B-4t4c-ethip6-ip6base-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test at 2x 9.4mpps. +| | [Tags] | 78B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 9.4mpps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc08-1518B-4t4c-ethip6-ip6base-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc09-9000B-4t4c-ethip6-ip6base-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-ndrpdrdisc.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-ndrpdrdisc.robot new file mode 100644 index 0000000000..3999677ffb --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-ndrpdrdisc.robot @@ -0,0 +1,436 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | BASE | IP6BASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput IPv6 routing test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with +| ... | 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 253 flows per flow-group) with all packets +| ... | containing Ethernet header, IPv6 header and static payload. +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253 + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 78B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc02-78B-1t1c-ethip6-ip6base-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 78B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc03-1518B-1t1c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc04-1518B-1t1c-ethip6-ip6base-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc05-9000B-1t1c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc06-9000B-1t1c-ethip6-ip6base-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc07-78B-2t2c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 78B | 2T2C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc08-78B-2t2c-ethip6-ip6base-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 78B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc09-1518B-2t2c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc10-1518B-2t2c-ethip6-ip6base-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc11-9000B-2t2c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc12-9000B-2t2c-ethip6-ip6base-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc13-78B-4t4c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 78B | 4T4C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc14-78B-4t4c-ethip6-ip6base-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 78B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc15-1518B-4t4c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc16-1518B-4t4c-ethip6-ip6base-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc17-9000B-4t4c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc18-9000B-4t4c-ethip6-ip6base-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-pdrchk.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-pdrchk.robot new file mode 100644 index 0000000000..5ca64f5790 --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6base-pdrchk.robot @@ -0,0 +1,183 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PDRCHK +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | BASE | IP6BASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance pdrchk test +| ... +| Documentation | *Reference PDR throughput IPv6 routing verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with +| ... | 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-PDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-PDR value is periodically updated acording to +| ... | formula: ref-PDR = 0.9x PDR, where PDR is found in RFC2544 long +| ... | performance tests for the same DUT configuration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv6 header and static +| ... | payload. MAC addresses are matching MAC addresses of the TG node +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253 + +*** Keywords *** +| Check PDR for IPv6 routing +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with ${wt} thread, ${wt} phy core,\ +| | ... | ${rxq} receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for ${framesize} Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Arguments] | ${framesize} | ${rate} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${rate} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Traffic should pass with partial loss | ${perf_trial_duration} +| | ... | ${rate} | ${framesize} | ${traffic_profile} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 78B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for IPv6 routing +| | framesize=${78} | rate=3.9mpps | wt=1 | rxq=1 + +| tc02-1518B-1t1c-ethip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for IPv6 routing +| | framesize=${1518} | rate=400000pps | wt=1 | rxq=1 + +| tc03-9000B-1t1c-ethip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for IPv6 routing +| | framesize=${9000} | rate=60000pps | wt=1 | rxq=1 + +| tc04-78B-2t2c-ethip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 78B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for IPv6 routing +| | framesize=${78} | rate=6.0mpps | wt=2 | rxq=1 + +| tc05-1518B-2t2c-ethip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for IPv6 routing +| | framesize=${1518} | rate=400000pps | wt=2 | rxq=1 + +| tc06-9000B-2t2c-ethip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for IPv6 routing +| | framesize=${9000} | rate=60000pps | wt=2 | rxq=1 + +| tc07-78B-4t4c-ethip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 78B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for IPv6 routing +| | framesize=${78} | rate=6.1mpps | wt=4 | rxq=2 + +| tc08-1518B-4t4c-ethip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for IPv6 routing +| | framesize=${1518} | rate=400000pps | wt=4 | rxq=2 + +| tc09-9000B-4t4c-ethip6-ip6base-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for IPv6 routing +| | framesize=${9000} | rate=60000pps | wt=4 | rxq=2 diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale200k-ndrchk.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale200k-ndrchk.robot new file mode 100644 index 0000000000..a6f8c980e1 --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale200k-ndrchk.robot @@ -0,0 +1,201 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | SCALE | FIB_200K +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance ndrchk test +| ... +| Documentation | *Reference NDR throughput IPv6 routing verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing and 2x100k static IPv6 /64 route entries. DUT1 and DUT2 tested +| ... | with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT confiiguration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 100k flows per flow-group) with +| ... | all packets containing Ethernet header, IPv6 header and static +| ... | payload. Incrementing of IP.dst (IPv6 destination address) field is +| ... | applied to both streams. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${rts_per_flow}= | ${100000} + +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6dst${rts_per_flow} +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6scale200k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test at 2x 2.3mpps. +| | [Tags] | 78B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 2.3mpps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc02-1518B-1t1c-ethip6-ip6scale200k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc03-9000B-1t1c-ethip6-ip6scale200k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc04-78B-2t2c-ethip6-ip6scale200k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test at 2x 5.0mpps. +| | [Tags] | 78B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 5.0mpps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc05-1518B-2t2c-ethip6-ip6scale200k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc06-9000B-2t2c-ethip6-ip6scale200k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc07-78B-4t4c-ethip6-ip6scale200k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test at 2x 5.7mpps. +| | [Tags] | 78B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 5.7mpps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc08-1518B-4t4c-ethip6-ip6scale200k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc09-9000B-4t4c-ethip6-ip6scale200k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale200k-ndrpdrdisc.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale200k-ndrpdrdisc.robot new file mode 100644 index 0000000000..f64102384d --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale200k-ndrpdrdisc.robot @@ -0,0 +1,457 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | SCALE | FIB_200K +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput IPv6 routing test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing and 2x100k static IPv6 /64 route entries. DUT1 and DUT2 tested +| ... | with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 100k flows per flow-group) with all packets +| ... | containing Ethernet header, IPv6 header withq IP and static payload. +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | Incrementing of IP.dst (IPv6 destination address) field is applied to +| ... | both streams. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +| ${rts_per_flow}= | ${100000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6dst${rts_per_flow} + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6scale200k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 78B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc02-78B-1t1c-ethip6-ip6scale200k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 78B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc03-1518B-1t1c-ethip6-ip6scale200k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc04-1518B-1t1c-ethip6-ip6scale200k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc05-9000B-1t1c-ethip6-ip6scale200k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc06-9000B-1t1c-ethip6-ip6scale200k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc07-78B-2t2c-ethip6-ip6scale200k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 78B | 2T2C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc08-78B-2t2c-ethip6-ip6scale200k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 78B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc09-1518B-2t2c-ethip6-ip6scale200k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc10-1518B-2t2c-ethip6-ip6scale200k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc11-9000B-2t2c-ethip6-ip6scale200k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc12-9000B-2t2c-ethip6-ip6scale200k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc13-78B-4t4c-ethip6-ip6scale200k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 78B | 4T4C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc14-78B-4t4c-ethip6-ip6scale200k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 78B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc15-1518B-4t4c-ethip6-ip6scale200k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc16-1518B-4t4c-ethip6-ip6scale200k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc17-9000B-4t4c-ethip6-ip6scale200k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc18-9000B-4t4c-ethip6-ip6scale200k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale20k-ndrchk.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale20k-ndrchk.robot new file mode 100644 index 0000000000..ebf642f9b5 --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale20k-ndrchk.robot @@ -0,0 +1,201 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | SCALE | FIB_20K +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance ndrchk test +| ... +| Documentation | *Reference NDR throughput IPv6 routing verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested +| ... | with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT confiiguration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 10k flows per flow-group) with +| ... | all packets containing Ethernet header, IPv6 header and static +| ... | payload. Incrementing of IP.dst (IPv6 destination address) field is +| ... | applied to both streams. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${rts_per_flow}= | ${10000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6dst${rts_per_flow} + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6scale20k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test at 2x 2.9mpps. +| | [Tags] | 78B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 2.9mpps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc02-1518B-1t1c-ethip6-ip6scale20k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc03-9000B-1t1c-ethip6-ip6scale20k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc04-78B-2t2c-ethip6-ip6scale20k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test at 2x 7.0mpps. +| | [Tags] | 78B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 7.0mpps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc05-1518B-2t2c-ethip6-ip6scale20k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc06-9000B-2t2c-ethip6-ip6scale20k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc07-78B-4t4c-ethip6-ip6scale20k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test at 2x 9.6mpps. +| | [Tags] | 78B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 10.0mpps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc08-1518B-4t4c-ethip6-ip6scale20k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc09-9000B-4t4c-ethip6-ip6scale20k-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale20k-ndrpdrdisc.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale20k-ndrpdrdisc.robot new file mode 100644 index 0000000000..4337c0d6a3 --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale20k-ndrpdrdisc.robot @@ -0,0 +1,457 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | SCALE | FIB_20K +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput IPv6 routing test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested +| ... | with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 10k flows per flow-group) with all packets +| ... | containing Ethernet header, IPv6 header withq IP and static payload. +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | Incrementing of IP.dst (IPv6 destination address) field is applied to +| ... | both streams. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +| ${rts_per_flow}= | ${10000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6dst${rts_per_flow} + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6scale20k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 78B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc02-78B-1t1c-ethip6-ip6scale20k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 78B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc03-1518B-1t1c-ethip6-ip6scale20k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc04-1518B-1t1c-ethip6-ip6scale20k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc05-9000B-1t1c-ethip6-ip6scale20k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc06-9000B-1t1c-ethip6-ip6scale20k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc07-78B-2t2c-ethip6-ip6scale20k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 78B | 2T2C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc08-78B-2t2c-ethip6-ip6scale20k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 78B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc09-1518B-2t2c-ethip6-ip6scale20k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc10-1518B-2t2c-ethip6-ip6scale20k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc11-9000B-2t2c-ethip6-ip6scale20k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc12-9000B-2t2c-ethip6-ip6scale20k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc13-78B-4t4c-ethip6-ip6scale20k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 78B | 4T4C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc14-78B-4t4c-ethip6-ip6scale20k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 78B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc15-1518B-4t4c-ethip6-ip6scale20k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc16-1518B-4t4c-ethip6-ip6scale20k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc17-9000B-4t4c-ethip6-ip6scale20k-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc18-9000B-4t4c-ethip6-ip6scale20k-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale2m-ndrchk.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale2m-ndrchk.robot new file mode 100644 index 0000000000..c3411cebd8 --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale2m-ndrchk.robot @@ -0,0 +1,210 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | SCALE | FIB_2M +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance ndrchk test +| ... +| Documentation | *Reference NDR throughput IPv6 routing verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing and 2x1M static IPv6 /64 route entries. DUT1 and DUT2 tested +| ... | with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT confiiguration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 1M flows per flow-group) with +| ... | all packets containing Ethernet header, IPv6 header and static +| ... | payload. Incrementing of IP.dst (IPv6 destination address) field is +| ... | applied to both streams. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${rts_per_flow}= | ${1000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6dst${rts_per_flow} + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6scale2m-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test at 2x 1.8mpps. +| | [Tags] | 78B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 1.8mpps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} +| | ... | ${traffic_profile} + +| tc02-1518B-1t1c-ethip6-ip6scale2m-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} +| | ... | ${traffic_profile} + +| tc03-9000B-1t1c-ethip6-ip6scale2m-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} +| | ... | ${traffic_profile} + +| tc04-78B-2t2c-ethip6-ip6scale2m-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test at 2x 4.0mpps. +| | [Tags] | 78B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 4.0mpps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} +| | ... | ${traffic_profile} + +| tc05-1518B-2t2c-ethip6-ip6scale2m-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} +| | ... | ${traffic_profile} + +| tc06-9000B-2t2c-ethip6-ip6scale2m-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} +| | ... | ${traffic_profile} + +| tc07-78B-4t4c-ethip6-ip6scale2m-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 78 Byte +| | ... | frames using single trial throughput test at 2x 6.8mpps. +| | [Tags] | 78B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${78} +| | ${rate}= | Set Variable | 6.8mpps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} +| | ... | ${traffic_profile} + +| tc08-1518B-4t4c-ethip6-ip6scale2m-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} +| | ... | ${traffic_profile} + +| tc09-9000B-4t4c-ethip6-ip6scale2m-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} +| | ... | ${traffic_profile} diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale2m-ndrpdrdisc.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale2m-ndrpdrdisc.robot new file mode 100644 index 0000000000..1259fd9130 --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale2m-ndrpdrdisc.robot @@ -0,0 +1,457 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | SCALE | FIB_2M +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput IPv6 routing test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing and 2x1M static IPv6 /64 route entries. DUT1 and DUT2 tested +| ... | with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 1M flows per flow-group) with all packets +| ... | containing Ethernet header, IPv6 header withq IP and static payload. +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | Incrementing of IP.dst (IPv6 destination address) field is applied to +| ... | both streams. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +| ${rts_per_flow}= | ${1000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6dst${rts_per_flow} + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6scale2m-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 78B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc02-78B-1t1c-ethip6-ip6scale2m-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 78B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc03-1518B-1t1c-ethip6-ip6scale2m-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc04-1518B-1t1c-ethip6-ip6scale2m-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc05-9000B-1t1c-ethip6-ip6scale2m-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc06-9000B-1t1c-ethip6-ip6scale2m-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc07-78B-2t2c-ethip6-ip6scale2m-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 78B | 2T2C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc08-78B-2t2c-ethip6-ip6scale2m-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 78B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc09-1518B-2t2c-ethip6-ip6scale2m-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc10-1518B-2t2c-ethip6-ip6scale2m-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc11-9000B-2t2c-ethip6-ip6scale2m-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc12-9000B-2t2c-ethip6-ip6scale2m-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc13-78B-4t4c-ethip6-ip6scale2m-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 78B | 4T4C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc14-78B-4t4c-ethip6-ip6scale2m-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 78 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 78B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc15-1518B-4t4c-ethip6-ip6scale2m-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc16-1518B-4t4c-ethip6-ip6scale2m-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc17-9000B-4t4c-ethip6-ip6scale2m-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc18-9000B-4t4c-ethip6-ip6scale2m-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} diff --git a/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale2m-pdrchk.robot b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale2m-pdrchk.robot new file mode 100644 index 0000000000..977e73ff2a --- /dev/null +++ b/tests/vpp/perf/ip6/10ge2p1x520-ethip6-ip6scale2m-pdrchk.robot @@ -0,0 +1,185 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PDRCHK +| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | SCALE | FIB_2M +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance pdrchk test +| ... +| Documentation | *Reference PDR throughput IPv6 routing verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing and 2x1M static IPv6 /64 route entries. DUT1 and DUT2 tested +| ... | with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-PDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-PDR value is periodically updated acording to +| ... | formula: ref-PDR = 0.9x PDR, where PDR is found in RFC2544 long +| ... | performance tests for the same DUT confiiguration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 1M flows per flow-group) with +| ... | all packets containing Ethernet header, IPv6 header and static +| ... | payload. Incrementing of IP.dst (IPv6 destination address) field is +| ... | applied to both streams. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${rts_per_flow}= | ${1000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6dst${rts_per_flow} + +*** Keywords *** +| Check PDR for IPv6 scaled routing +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with ${wt} thread, ${wt} phy core,\ +| | ... | ${rxq} receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for ${framesize} Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Arguments] | ${framesize} | ${rate} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${rate} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding with scaling in 3-node circular topology +| | ... | ${rts_per_flow} +| | Then Traffic should pass with partial loss | ${perf_trial_duration} +| | ... | ${rate} | ${framesize} | ${traffic_profile} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6scale2m-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 78B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for IPv6 scaled routing +| | framesize=${78} | rate=1.8mpps | wt=1 | rxq=1 + +| tc02-1518B-1t1c-ethip6-ip6scale2m-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for IPv6 scaled routing +| | framesize=${1518} | rate=400000pps | wt=1 | rxq=1 + +| tc03-9000B-1t1c-ethip6-ip6scale2m-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for IPv6 scaled routing +| | framesize=${9000} | rate=60000pps | wt=1 | rxq=1 + +| tc04-78B-2t2c-ethip6-ip6scale2m-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 78B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for IPv6 scaled routing +| | framesize=${78} | rate=4.0mpps | wt=2 | rxq=1 + +| tc05-1518B-2t2c-ethip6-ip6scale2m-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for IPv6 scaled routing +| | framesize=${1518} | rate=400000pps | wt=2 | rxq=1 + +| tc06-9000B-2t2c-ethip6-ip6scale2m-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for IPv6 scaled routing +| | framesize=${900} | rate=138580pps | wt=2 | rxq=1 + +| tc07-78B-4t4c-ethip6-ip6scale2m-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 78 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 78B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for IPv6 scaled routing +| | framesize=${78} | rate=6.4mpps | wt=4 | rxq=2 + +| tc08-1518B-4t4c-ethip6-ip6scale2m-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for IPv6 scaled routing +| | framesize=${1518} | rate=400000pps | wt=4 | rxq=2 + +| tc09-9000B-4t4c-ethip6-ip6scale2m-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for IPv6 scaled routing +| | framesize=${9000} | rate=60000pps | wt=4 | rxq=2 diff --git a/tests/vpp/perf/ip6/40ge2p1xl710-ethip6-ip6base-ndrpdrdisc.robot b/tests/vpp/perf/ip6/40ge2p1xl710-ethip6-ip6base-ndrpdrdisc.robot new file mode 100644 index 0000000000..4c45fdd266 --- /dev/null +++ b/tests/vpp/perf/ip6/40ge2p1xl710-ethip6-ip6base-ndrpdrdisc.robot @@ -0,0 +1,183 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-XL710 | ETH | IP6FWD | BASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-XL710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput IPv6 routing test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv6 for IPv6 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6 +| ... | routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with +| ... | 2p40GE NIC XL710 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 253 flows per flow-group) with all packets +| ... | containing Ethernet header, IPv6 header and static payload. +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps +| ${s_24.5G} | ${24500000000} +# XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps +| ${s_18.75Mpps} | ${18750000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253 + +*** Test Cases *** +| tc01-78B-1t1c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 18.75Mpps rate, step 100kpps. +| | [Tags] | 78B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Set Variable | ${s_18.75Mpps} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc03-1518B-1t1c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 24.5G rate, step 10kpps. +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc07-78B-2t2c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 18.75Mpps rate, step 100kpps. +| | [Tags] | 78B | 2T2C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Set Variable | ${s_18.75Mpps} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc09-1518B-2t2c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 24.5G rate, step 10kpps. +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc13-78B-4t4c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 78 Byte frames +| | ... | using binary search start at 18.75Mpps rate, step 100kpps. +| | [Tags] | 78B | 4T4C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${78} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Set Variable | ${s_18.75Mpps} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc15-1518B-4t4c-ethip6-ip6base-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 24.5G rate, step 10kpps. +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize IPv6 forwarding in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} |