diff options
Diffstat (limited to 'tests/vpp/perf/ip6_tunnels/10ge2p1x520-ethip6lispip4-ip6base-mrr.robot')
| -rw-r--r-- | tests/vpp/perf/ip6_tunnels/10ge2p1x520-ethip6lispip4-ip6base-mrr.robot | 134 |
1 files changed, 0 insertions, 134 deletions
diff --git a/tests/vpp/perf/ip6_tunnels/10ge2p1x520-ethip6lispip4-ip6base-mrr.robot b/tests/vpp/perf/ip6_tunnels/10ge2p1x520-ethip6lispip4-ip6base-mrr.robot deleted file mode 100644 index 7e5605564d..0000000000 --- a/tests/vpp/perf/ip6_tunnels/10ge2p1x520-ethip6lispip4-ip6base-mrr.robot +++ /dev/null @@ -1,134 +0,0 @@ -# Copyright (c) 2018 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance/performance_setup.robot -| Resource | resources/libraries/robot/overlay/lisp_static_adjacency.robot -| Variables | resources/test_data/lisp/performance/lisp_static_adjacency.py -| ... -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR -| ... | NIC_Intel-X520-DA2 | IP6FWD | ENCAP | LISP | IP4UNRLAY | IP6OVRLAY -| ... -| Suite Setup | Set up 3-node performance topology with DUT's NIC model -| ... | L3 | Intel-X520-DA2 -| Suite Teardown | Tear down 3-node performance topology -| ... -| Test Setup | Set up performance test -| ... -| Test Teardown | Tear down performance mrr test -| ... -| Test Template | Local Template -| ... -| Documentation | *RFC6830: Pkt throughput Lisp test cases* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ -| ... | with single links between nodes.\ -| ... | *[Enc] Packet Encapsulations:* Eth-IPv6-LISP-IPv4 on DUT1-DUT2,\ -| ... | Eth-IPv6 on TG-DUTn for IPv6 routing over LISPoIPv4 tunnel.\ -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6\ -| ... | routing and static routes. LISPoIPv4 tunnel is configured between\ -| ... | DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic\ -| ... | by Intel.\ -| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\ -| ... | at line rate and reports total received/sent packets over trial period.\ -| ... | *[Ref] Applicable standard specifications:* RFC6830. - -*** Variables *** -# X520-DA2 bandwidth limit -| ${s_limit}= | ${10000000000} -# LISP overhead -| ${overhead}= | 48 -# Traffic profile: -| ${traffic_profile}= | trex-sl-3n-ethip6-ip6src253 - -*** Keywords *** -| Local Template -| | [Documentation] -| | ... | [Cfg] DUT runs IPv6 LISP remote static mappings and whitelist\ -| | ... | filters config.\ -| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.\ -| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ -| | ... | trial throughput test.\ -| | ... -| | ... | *Arguments:* -| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). -| | ... | Type: integer, string -| | ... | - phy_cores - Number of physical cores. Type: integer -| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer -| | ... -| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} -| | ... -| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} -| | And Add PCI devices to all DUTs -| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg -| | ... | ${s_limit} | ${framesize} | overhead=${overhead} -| | And Apply startup configuration on all VPP DUTs -| | When Initialize LISP IPv6 over IPv4 forwarding in 3-node circular topology -| | ... | ${dut1_to_dut2_ip6o4} | ${dut1_to_tg_ip6o4} | ${dut2_to_dut1_ip6o4} -| | ... | ${dut2_to_tg_ip6o4} | ${tg_prefix6o4} | ${dut_prefix6o4} -| | And Configure LISP topology in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${NONE} -| | ... | ${dut2} | ${dut2_if1} | ${NONE} -| | ... | ${duts_locator_set} | ${dut1_ip6o4_eid} | ${dut2_ip6o4_eid} -| | ... | ${dut1_ip6o4_static_adjacency} | ${dut2_ip6o4_static_adjacency} -| | Then Traffic should pass with maximum rate -| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} - -*** Test Cases *** -| tc01-78B-1c-ethip6lispip4-ip6base-mrr -| | [Tags] | 78B | 1C -| | framesize=${78} | phy_cores=${1} - -| tc02-78B-2c-ethip6lispip4-ip6base-mrr -| | [Tags] | 78B | 2C -| | framesize=${78} | phy_cores=${2} - -| tc03-78B-4c-ethip6lispip4-ip6base-mrr -| | [Tags] | 78B | 4C -| | framesize=${78} | phy_cores=${4} - -| tc04-1518B-1c-ethip6lispip4-ip6base-mrr -| | [Tags] | 1518B | 1C -| | framesize=${1518} | phy_cores=${1} - -| tc05-1518B-2c-ethip6lispip4-ip6base-mrr -| | [Tags] | 1518B | 2C -| | framesize=${1518} | phy_cores=${2} - -| tc06-1518B-4c-ethip6lispip4-ip6base-mrr -| | [Tags] | 1518B | 4C -| | framesize=${1518} | phy_cores=${4} - -| tc07-9000B-1c-ethip6lispip4-ip6base-mrr -| | [Tags] | 9000B | 1C -| | framesize=${9000} | phy_cores=${1} - -| tc08-9000B-2c-ethip6lispip4-ip6base-mrr -| | [Tags] | 9000B | 2C -| | framesize=${9000} | phy_cores=${2} - -| tc09-9000B-4c-ethip6lispip4-ip6base-mrr -| | [Tags] | 9000B | 4C -| | framesize=${9000} | phy_cores=${4} - -| tc10-IMIX-1c-ethip6lispip4-ip6base-mrr -| | [Tags] | IMIX | 1C -| | framesize=IMIX_v4_1 | phy_cores=${1} - -| tc11-IMIX-2c-ethip6lispip4-ip6base-mrr -| | [Tags] | IMIX | 2C -| | framesize=IMIX_v4_1 | phy_cores=${2} - -| tc12-IMIX-4c-ethip6lispip4-ip6base-mrr -| | [Tags] | IMIX | 4C -| | framesize=IMIX_v4_1 | phy_cores=${4} |