diff options
Diffstat (limited to 'tests/vpp/perf/l2/10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.robot')
| -rw-r--r-- | tests/vpp/perf/l2/10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.robot | 27 |
1 files changed, 13 insertions, 14 deletions
diff --git a/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.robot b/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.robot index d034b1fd9f..e6269f7861 100644 --- a/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.robot +++ b/tests/vpp/perf/l2/10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.robot @@ -28,23 +28,22 @@ | ... | Test Template | Local Template | ... -| Documentation | *Raw results L2BD test cases with 802.1q test cases* +| Documentation | *Raw results L2BD with IEEE 802.1Q test cases* | ... | ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ | ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.\ -| ... | 802.1q tagging is applied on link between DUT1 and DUT2. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. IEEE\ +| ... | 802.1Q tagging is applied on link between DUT1 and DUT2. | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge\ -| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC -| ... | X710 by Intel. +| ... | domain and MAC learning enabled. DUT1 and DUT2 are tested with 2p10GE\ +| ... | NIC X710 by Intel. | ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\ | ... | at line rate and reports total received/sent packets over trial period.\ -| ... | Test packets are generated by TG on\ -| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\ -| ... | (flow-group per direction, 254 flows per flow-group) with all packets\ -| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\ -| ... | payload. MAC addresses are matching MAC addresses of the TG node\ -| ... | interfaces. +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\ +| ... | flow-group) with all packets containing Ethernet header, IPv4 header\ +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\ +| ... | addresses of the TG node interfaces. | ... | *[Ref] Applicable standard specifications:* RFC2544. *** Variables *** @@ -62,8 +61,8 @@ *** Keywords *** | Local Template | | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with VLAN with ${phy_cores} phy -| | ... | core(s). +| | ... | [Cfg] Each DUT runs L2BD config with VLAN and uses ${phy_cores}\ +| | ... | physical core(s) for worker threads. | | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ | | ... | trial throughput test. | | ... @@ -80,7 +79,7 @@ | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg | | ... | ${s_limit} | ${framesize} | overhead=${overhead} | | And Apply startup configuration on all VPP DUTs -| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in a 3-node circular topology +| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in circular topology | | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite} | | Then Traffic should pass with maximum rate | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} |