diff options
Diffstat (limited to 'tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-mrr.robot')
| -rw-r--r-- | tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-mrr.robot | 137 |
1 files changed, 0 insertions, 137 deletions
diff --git a/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-mrr.robot b/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-mrr.robot deleted file mode 100644 index 283ab6b10d..0000000000 --- a/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-mrr.robot +++ /dev/null @@ -1,137 +0,0 @@ -# Copyright (c) 2018 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance/performance_setup.robot -| ... -| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR -| ... | NIC_Intel-XXV710 | BASE | DOT1Q | L2BDMACLRN -| ... -| Suite Setup | Set up 2-node performance topology with DUT's NIC model -| ... | L2 | Intel-XXV710 -| ... -| Suite Teardown | Tear down 2-node performance topology -| ... -| Test Setup | Set up performance test -| ... -| Test Teardown | Tear down performance mrr test -| ... -| Test Template | Local Template -| ... -| Documentation | *Raw results L2BD with IEEE 802.1Q test cases* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\ -| ... | single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. IEEE\ -| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2. -| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\ -| ... | and MAC learning enabled. DUT1 is tested with 2p25GE NIC XXV710 by\ -| ... | Intel. -| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\ -| ... | at line rate and reports total received/sent packets over trial period.\ -| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\ -| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\ -| ... | flow-group) with all packets containing Ethernet header, IPv4 header\ -| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\ -| ... | addresses of the TG node interfaces. -| ... | *[Ref] Applicable standard specifications:* RFC2544. - -*** Variables *** -| ${subid}= | 10 -| ${tag_rewrite}= | pop-1 -| ${overhead}= | ${4} -# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps -| ${s_24.5G}= | ${24500000000} -# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps -| ${s_18.75Mpps}= | ${18750000} -# Bridge domain IDs -| ${bd_id1}= | 1 -| ${bd_id2}= | 2 -# Traffic profile: -| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254 - -*** Keywords *** -| Local Template -| | [Documentation] -| | ... | [Cfg] Each DUT runs L2BD config with VLAN and uses ${phy_cores}\ -| | ... | physical core(s) for worker threads. -| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ -| | ... | trial throughput test. -| | ... -| | ... | *Arguments:* -| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). -| | ... | Type: integer, string -| | ... | - phy_cores - Number of physical cores. Type: integer -| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer -| | ... -| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} -| | ... -| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} -| | And Add PCI devices to all DUTs -| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg -| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps} -| | ... | overhead=${overhead} -| | And Apply startup configuration on all VPP DUTs -| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in circular topology -| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite} -| | Then Traffic should pass with maximum rate -| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} - -*** Test Cases *** -| tc01-64B-1c-dot1q-l2bdbasemaclrn-mrr -| | [Tags] | 64B | 1C -| | framesize=${64} | phy_cores=${1} - -| tc02-64B-2c-dot1q-l2bdbasemaclrn-mrr -| | [Tags] | 64B | 2C -| | framesize=${64} | phy_cores=${2} - -| tc03-64B-4c-dot1q-l2bdbasemaclrn-mrr -| | [Tags] | 64B | 4C -| | framesize=${64} | phy_cores=${4} - -| tc04-1518B-1c-dot1q-l2bdbasemaclrn-mrr -| | [Tags] | 1518B | 1C -| | framesize=${1518} | phy_cores=${1} - -| tc05-1518B-2c-dot1q-l2bdbasemaclrn-mrr -| | [Tags] | 1518B | 2C -| | framesize=${1518} | phy_cores=${2} - -| tc06-1518B-4c-dot1q-l2bdbasemaclrn-mrr -| | [Tags] | 1518B | 4C -| | framesize=${1518} | phy_cores=${4} - -| tc07-9000B-1c-dot1q-l2bdbasemaclrn-mrr -| | [Tags] | 9000B | 1C -| | framesize=${9000} | phy_cores=${1} - -| tc08-9000B-2c-dot1q-l2bdbasemaclrn-mrr -| | [Tags] | 9000B | 2C -| | framesize=${9000} | phy_cores=${2} - -| tc09-9000B-4c-dot1q-l2bdbasemaclrn-mrr -| | [Tags] | 9000B | 4C -| | framesize=${9000} | phy_cores=${4} - -| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-mrr -| | [Tags] | IMIX | 1C -| | framesize=IMIX_v4_1 | phy_cores=${1} - -| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-mrr -| | [Tags] | IMIX | 2C -| | framesize=IMIX_v4_1 | phy_cores=${2} - -| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-mrr -| | [Tags] | IMIX | 4C -| | framesize=IMIX_v4_1 | phy_cores=${4} |