1 files changed, 143 insertions, 0 deletions
diff --git a/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-ndrpdr.robot b/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-ndrpdr.robot
new file mode 100644
index 0000000000..0934bc1f2b
--- /dev/null
+++ b/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-ndrpdr.robot
@@ -0,0 +1,143 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-XXV710 | BASE | DOT1Q | L2BDMACLRN
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L2 | Intel-XXV710
+| ...
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\
+| ... | single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
+| ... | and MAC learning enabled. DUT1 is tested with 2p25GE NIC XXV710 by\
+| ... | Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\
+| ... | generated by TG on links to DUT1. TG traffic profile contains two L3\
+| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with\
+| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61\
+| ... | and static payload. MAC addresses are matching MAC addresses of the TG\
+| ... | node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+| ${subid}= | 10
+| ${tag_rewrite}= | pop-1
+| ${overhead}= | ${4}
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G}= | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps}= | ${18750000}
+# Bridge domain IDs
+| ${bd_id1}= | 1
+| ${bd_id2}= | 2
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254
+
+*** Keywords ***
+| Local Template
+| | [Documentation]
+| | ... | [Cfg] Each DUT runs L2BD config with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | ... | overhead=${overhead}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize L2 bridge domains with VLAN dot1q sub-interfaces in circular topology
+| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite}
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}