diff options
Diffstat (limited to 'tests/vpp/perf/l2')
15 files changed, 4641 insertions, 0 deletions
diff --git a/tests/vpp/perf/l2/10ge2p1vic1227-eth-l2bdbasemaclrn-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1vic1227-eth-l2bdbasemaclrn-ndrpdrdisc.robot new file mode 100644 index 0000000000..51eb235f24 --- /dev/null +++ b/tests/vpp/perf/l2/10ge2p1vic1227-eth-l2bdbasemaclrn-ndrpdrdisc.robot @@ -0,0 +1,288 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Cisco-VIC-1227 | ETH | L2BDMACLRN | BASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Cisco-VIC-1227 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput L2BD test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge-\ +| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC +| ... | Cisco-VIC-1227. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using either binary search or linear search\ +| ... | algorithms with configured starting rate and final step that determines\ +| ... | throughput measurement resolution. Test packets are generated by TG on\ +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\ +| ... | (flow-group per direction, 253 flows per flow-group) with all packets\ +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\ +| ... | payload. MAC addresses are matching MAC addresses of the TG node\ +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# Cisco-VIC-1227 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| L2 Bridge Domain NDR Binary Search +| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq} +| | # Test Variables required for test teardown +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Set Test Documentation | [Cfg] DUT runs L2BD switching config with ${wt}\ +| | Set Test Documentation | thread, ${wt} phy core, ${rxq}\ | append=True +| | Set Test Documentation | receive queue per NIC port. | append=True +| | Set Test Documentation | [Ver] Find NDR for ${framesize} Byte\ | append=True +| | Set Test Documentation | frames using binary search start at\ | append=True +| | Set Test Documentation | 10GE linerate, step ${threshold}pps. | append=True +| | Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | Add PCI devices to DUTs in 3-node single link topology +| | Run Keyword If | ${framesize} < ${1522} | Add no multi seg to all DUTs +| | Apply startup configuration on all VPP DUTs +| | Initialize L2 bridge domain in 3-node circular topology +| | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| L2 Bridge Domain PDR Binary Search +| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq} +| | # Test Variables required for test teardown +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Set Test Documentation | [Cfg] DUT runs L2BD switching config with ${wt}\ +| | Set Test Documentation | thread, ${wt} phy core, ${rxq}\ | append=True +| | Set Test Documentation | receive queue per NIC port. | append=True +| | Set Test Documentation | [Ver] Find PDR for ${framesize} Byte\ | append=True +| | Set Test Documentation | frames using binary search start at\ | append=True +| | Set Test Documentation | 10GE linerate, step ${threshold}pps, | append=True +| | Set Test Documentation | LT=${perf_pdr_loss_acceptance} | append=True +| | Set Test Documentation | ${perf_pdr_loss_acceptance_type}. | append=True +| | Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | Add PCI devices to DUTs in 3-node single link topology +| | Run Keyword If | ${framesize} < ${1522} | Add no multi seg to all DUTs +| | Apply startup configuration on all VPP DUTs +| | Initialize L2 bridge domain in 3-node circular topology +| | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=1 | rxq=1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc02-64B-1t1c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=1 | rxq=1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps, LT=0.5%. +| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc03-1518B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=1 | rxq=1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc04-1518B-1t1c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=1 | rxq=1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc05-9000B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=1 | rxq=1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc06-9000B-1t1c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=1 | rxq=1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc07-64B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=2 | rxq=1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc08-64B-2t2c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=2 | rxq=1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps, LT=0.5%. +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc09-1518B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=2 | rxq=1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc10-1518B-2t2c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=2 | rxq=1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc11-9000B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=2 | rxq=1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc12-9000B-2t2c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=2 | rxq=1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc13-64B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=4 | rxq=2 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc14-64B-4t4c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=4 | rxq=2 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps, LT=0.5%. +| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc15-1518B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=4 | rxq=2 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc16-1518B-4t4c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=4 | rxq=2 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc17-9000B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=4 | rxq=2 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc18-9000B-4t4c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=4 | rxq=2 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search diff --git a/tests/vpp/perf/l2/10ge2p1x520-dot1ad-l2xcbase-ndrchk.robot b/tests/vpp/perf/l2/10ge2p1x520-dot1ad-l2xcbase-ndrchk.robot new file mode 100644 index 0000000000..4b4162581a --- /dev/null +++ b/tests/vpp/perf/l2/10ge2p1x520-dot1ad-l2xcbase-ndrchk.robot @@ -0,0 +1,279 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Resource | resources/libraries/robot/l2/tagging.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK +| ... | NIC_Intel-X520-DA2 | L2XCFWD | BASE | DOT1AD +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance ndrchk test +| ... +| Documentation | *Reference NDR throughput L2XC with 802.1ad verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 xconnect. +| ... | 802.1ad tagging is applied on link between DUT1 and DUT2 with inner 4B +| ... | vlan tag (id=100) and outer 4B vlan tag (id=200). +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT configuration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 +| ... | and static payload. MAC addresses are matching MAC addresses of the +| ... | TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${subid}= | 10 +| ${outer_vlan_id}= | 100 +| ${inner_vlan_id}= | 200 +| ${type_subif}= | two_tags +| ${tag_rewrite}= | pop-2 +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Test Cases *** +| tc01-64B-1t1c-dot1ad-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test at 2x 4.0mpps. +| | [Tags] | 64B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${64} +| | ${rate}= | Set Variable | 4.0mpps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc02-1514B-1t1c-dot1ad-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1514 Byte +| | ... | frames using single trial throughput test at 2x 810635pps. +| | [Tags] | 1514B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${1514} +| | ${rate}= | Set Variable | 810635pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc03-9000B-1t1c-dot1ad-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138458pps. +| | [Tags] | 9000B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138458pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc04-64B-2t2c-dot1ad-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 2 thread, 2 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test at 2x 8.5mpps. +| | [Tags] | 64B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${64} +| | ${rate}= | Set Variable | 8.5mpps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc05-1514B-2t2c-dot1ad-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 2 thread, 2 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1514 Byte +| | ... | frames using single trial throughput test at 2x 810635pps. +| | [Tags] | 1514B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${1514} +| | ${rate}= | Set Variable | 810635pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc06-9000B-2t2c-dot1ad-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 2 thread, 2 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138458pps. +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138458pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc07-64B-4t4c-dot1ad-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 4 thread, 4 phy core, \ +| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test at 2x 8.6mpps. +| | [Tags] | 64B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${64} +| | ${rate}= | Set Variable | 8.6mpps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc08-1514B-4t4c-dot1ad-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 4 thread, 4 phy core, \ +| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 1514 Byte +| | ... | frames using single trial throughput test at 2x 810635pps. +| | [Tags] | 1514B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${1514} +| | ${rate}= | Set Variable | 810635pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc09-9000B-4t4c-dot1ad-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 4 thread, 4 phy core, \ +| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138458pps. +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138458pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} diff --git a/tests/vpp/perf/l2/10ge2p1x520-dot1ad-l2xcbase-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1x520-dot1ad-l2xcbase-ndrpdrdisc.robot new file mode 100644 index 0000000000..17b907c91b --- /dev/null +++ b/tests/vpp/perf/l2/10ge2p1x520-dot1ad-l2xcbase-ndrpdrdisc.robot @@ -0,0 +1,606 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Resource | resources/libraries/robot/l2/tagging.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-X520-DA2 | L2XCFWD | BASE | DOT1AD +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput L2XC with 802.1ad test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 xconnect. +| ... | 802.1ad tagging is applied on link between DUT1 and DUT2 with inner 4B +| ... | vlan tag (id=100) and outer 4B vlan tag (id=200). +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 253 flows per flow-group) with all packets +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and +| ... | static payload. MAC addresses are matching MAC addresses of the TG +| ... | node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${subid}= | 10 +| ${outer_vlan_id}= | 100 +| ${inner_vlan_id}= | 200 +| ${type_subif}= | two_tags +| ${tag_rewrite}= | pop-2 +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Test Cases *** +| tc01-64B-1t1c-dot1ad-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc02-64B-1t1c-dot1ad-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc03-1514B-1t1c-dot1ad-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1514 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1514B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${1514} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc04-1514B-1t1c-dot1ad-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1514 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1514B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1514} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc05-9000B-1t1c-dot1ad-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc06-9000B-1t1c-dot1ad-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc07-64B-2t2c-dot1ad-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc08-64B-2t2c-dot1ad-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc09-1514B-2t2c-dot1ad-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1514 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1514B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1514} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc10-1514B-2t2c-dot1ad-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1514 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1514B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1514} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc11-9000B-2t2c-dot1ad-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc12-9000B-2t2c-dot1ad-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc13-64B-4t4c-dot1ad-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc14-64B-4t4c-dot1ad-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc15-1514B-4t4c-dot1ad-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1514 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1514B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1514} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc16-1514B-4t4c-dot1ad-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 1514 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1514B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1514} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc17-9000B-4t4c-dot1ad-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc18-9000B-4t4c-dot1ad-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 8} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} diff --git a/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-ndrchk.robot b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-ndrchk.robot new file mode 100644 index 0000000000..d3a67f3777 --- /dev/null +++ b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-ndrchk.robot @@ -0,0 +1,266 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Resource | resources/libraries/robot/l2/tagging.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK +| ... | NIC_Intel-X520-DA2 | L2XCFWD | BASE | DOT1Q +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance ndrchk test +| ... +| Documentation | *Reference NDR throughput L2XC with 802.1q verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. 802.1q +| ... | tagging is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT configuration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 +| ... | and static payload. MAC addresses are matching MAC addresses of the +| ... | TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${subid}= | 10 +| ${tag_rewrite}= | pop-1 +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Test Cases *** +| tc01-64B-1t1c-dot1q-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test at 2x 4.0mpps. +| | [Tags] | 64B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${64} +| | ${rate}= | Set Variable | 4.0mpps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc02-1518B-1t1c-dot1q-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 720000pps. +| | [Tags] | 1518B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 720000pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc03-9000B-1t1c-dot1q-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 120000pps. +| | [Tags] | 9000B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 120000pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc04-64B-2t2c-dot1q-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test at 2x 8.7mpps. +| | [Tags] | 64B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${64} +| | ${rate}= | Set Variable | 8.7mpps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc05-1518B-2t2c-dot1q-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 720000pps. +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 720000pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc06-9000B-2t2c-dot1q-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 120000pps. +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 120000pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc07-64B-4t4c-dot1q-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test at 2x 10.3mpps. +| | [Tags] | 64B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${64} +| | ${rate}= | Set Variable | 10.3mpps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc08-1518B-4t4c-dot1q-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 720000pps. +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 720000pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc09-9000B-4t4c-dot1q-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 120000pps. +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 120000pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} diff --git a/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-ndrpdrdisc.robot new file mode 100644 index 0000000000..a5a8580f29 --- /dev/null +++ b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-ndrpdrdisc.robot @@ -0,0 +1,584 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Resource | resources/libraries/robot/l2/tagging.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-X520-DA2 | L2XCFWD | BASE | DOT1Q +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput L2XC with 802.1q test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. 802.1q +| ... | tagging is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 253 flows per flow-group) with all packets +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static +| ... | payload. MAC addresses are matching MAC addresses of the TG node +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${subid}= | 10 +| ${tag_rewrite}= | pop-1 +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Test Cases *** +| tc01-64B-1t1c-dot1q-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc02-64B-1t1c-dot1q-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc03-1518B-1t1c-dot1q-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc04-1518B-1t1c-dot1q-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc05-9000B-1t1c-dot1q-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc06-9000B-1t1c-dot1q-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc07-64B-2t2c-dot1q-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc08-64B-2t2c-dot1q-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc09-1518B-2t2c-dot1q-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc10-1518B-2t2c-dot1q-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc11-9000B-2t2c-dot1q-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc12-9000B-2t2c-dot1q-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc13-64B-4t4c-dot1q-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc14-64B-4t4c-dot1q-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc15-1518B-4t4c-dot1q-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc16-1518B-4t4c-dot1q-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc17-9000B-4t4c-dot1q-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc18-9000B-4t4c-dot1q-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize + 4} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Set interfaces in path in 3-node circular topology up +| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology +| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} +| | And Configure L2 tag rewrite method on interfaces +| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} +| | ... | ${tag_rewrite} +| | And Connect interfaces and VLAN sub-interfaces using L2XC +| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} +| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-ndrchk.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-ndrchk.robot new file mode 100644 index 0000000000..598d45f6b6 --- /dev/null +++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-ndrchk.robot @@ -0,0 +1,192 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.NodePath +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK +| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | BASE | L2BDBASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance ndrchk test +| ... +| Documentation | *Reference NDR throughput L2BD verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- +| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC +| ... | X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT configuration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 +| ... | and static payload. MAC addresses are matching MAC addresses of the +| ... | TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test at 2x 4.9mpps. +| | [Tags] | 64B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${64} +| | ${rate}= | Set Variable | 4.9mpps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc02-1518B-1t1c-eth-l2bdbasemaclrn-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc03-9000B-1t1c-eth-l2bdbasemaclrn-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc04-64B-2t2c-eth-l2bdbasemaclrn-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test at 2x 10.4mpps. +| | [Tags] | 64B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${64} +| | ${rate}= | Set Variable | 10.4mpps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc05-1518B-2t2c-eth-l2bdbasemaclrn-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc06-9000B-2t2c-eth-l2bdbasemaclrn-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc07-64B-4t4c-eth-l2bdbasemaclrn-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test at 2x 10.4mpps. +| | [Tags] | 64B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${64} +| | ${rate}= | Set Variable | 10.4mpps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc08-1518B-4t4c-eth-l2bdbasemaclrn-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc09-9000B-4t4c-eth-l2bdbasemaclrn-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-ndrpdrdisc.robot new file mode 100644 index 0000000000..5234981c14 --- /dev/null +++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-ndrpdrdisc.robot @@ -0,0 +1,274 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | BASE | L2BDBASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput L2BD test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge-\ +| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NI +| ... | X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using either binary search or linear search\ +| ... | algorithms with configured starting rate and final step that determines\ +| ... | throughput measurement resolution. Test packets are generated by TG on\ +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\ +| ... | (flow-group per direction, 253 flows per flow-group) with all packets\ +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\ +| ... | payload. MAC addresses are matching MAC addresses of the TG node\ +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| L2 Bridge Domain NDR Binary Search +| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | Add PCI devices to DUTs in 3-node single link topology +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs +| | Apply startup configuration on all VPP DUTs +| | Initialize L2 bridge domain in 3-node circular topology +| | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| L2 Bridge Domain PDR Binary Search +| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | Add PCI devices to DUTs in 3-node single link topology +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs +| | Apply startup configuration on all VPP DUTs +| | Initialize L2 bridge domain in 3-node circular topology +| | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=1 | rxq=1 +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc02-64B-1t1c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=1 | rxq=1 +| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc03-1518B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=1 | rxq=1 +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc04-1518B-1t1c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=1 | rxq=1 +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc05-9000B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=1 | rxq=1 +| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc06-9000B-1t1c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=1 | rxq=1 +| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc07-64B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=2 | rxq=1 +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc08-64B-2t2c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=2 | rxq=1 +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc09-1518B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=2 | rxq=1 +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc10-1518B-2t2c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=2 | rxq=1 +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc11-9000B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=2 | rxq=1 +| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc12-9000B-2t2c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=2 | rxq=1 +| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc13-64B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=4 | rxq=2 +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc14-64B-4t4c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=4 | rxq=2 +| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc15-1518B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=4 | rxq=2 +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc16-1518B-4t4c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=4 | rxq=2 +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc17-9000B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=4 | rxq=2 +| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc18-9000B-4t4c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=4 | rxq=2 +| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-pdrchk.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-pdrchk.robot new file mode 100644 index 0000000000..58512392f7 --- /dev/null +++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-pdrchk.robot @@ -0,0 +1,184 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.NodePath +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PDRCHK +| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | BASE | L2BDBASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance pdrchk test +| ... +| Documentation | *Reference PDR throughput L2BD verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- +| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC +| ... | X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-PDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-PDR value is periodically updated acording to +| ... | formula: ref-PDR = 0.9x PDR, where PDR is found in RFC2544 long +| ... | performance tests for the same DUT configuration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 +| ... | and static payload. MAC addresses are matching MAC addresses of the +| ... | TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check PDR for L2 bridge domain +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with ${wt} thread, ${wt} phy core,\ +| | ... | ${rxq} receive queue per NIC port. +| | ... | [Ver] Verify ref-PDR for ${framesize} Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Arguments] | ${framesize} | ${rate} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${rate} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Traffic should pass with partial loss | ${perf_trial_duration} +| | ... | ${rate} | ${framesize} | ${traffic_profile} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-PDR for 64 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for L2 bridge domain +| | framesize=${64} | rate=4.9mpps | wt=1 | rxq=1 + +| tc02-1518B-1t1c-eth-l2bdbasemaclrn-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-PDR for 1518 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for L2 bridge domain +| | framesize=${1518} | rate=772105pps | wt=1 | rxq=1 + +| tc03-9000B-1t1c-eth-l2bdbasemaclrn-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-PDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for L2 bridge domain +| | framesize=${9000} | rate=110000pps | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2bdbasemaclrn-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-PDR for 64 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for L2 bridge domain +| | framesize=${64} | rate=10.4mpps | wt=2 | rxq=1 + +| tc05-1518B-2t2c-eth-l2bdbasemaclrn-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-PDR for 1518 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for L2 bridge domain +| | framesize=${1518} | rate=812743pps | wt=2 | rxq=1 + +| tc06-9000B-2t2c-eth-l2bdbasemaclrn-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-PDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for L2 bridge domain +| | framesize=${9000} | rate=100000pps | wt=2 | rxq=1 + +| tc07-64B-4t4c-eth-l2bdbasemaclrn-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 4 thread, 4 phy core,\ +| | ... | 2 receive queue per NIC port. +| | ... | [Ver] Verify ref-PDR for 64 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for L2 bridge domain +| | framesize=${64} | rate=10.4mpps | wt=4 | rxq=2 + +| tc08-1518B-4t4c-eth-l2bdbasemaclrn-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 4 thread, 4 phy core,\ +| | ... | 2 receive queue per NIC port. +| | ... | [Ver] Verify ref-PDR for 1518 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for L2 bridge domain +| | framesize=${1518} | rate=812743pps | wt=4 | rxq=2 + +| tc09-9000B-4t4c-eth-l2bdbasemaclrn-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD config with 4 thread, 4 phy core,\ +| | ... | 2 receive queue per NIC port. +| | ... | [Ver] Verify ref-PDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for L2 bridge domain +| | framesize=${9000} | rate=138580pps | wt=4 | rxq=2 diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-ndrchk.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-ndrchk.robot new file mode 100644 index 0000000000..13a2b7577f --- /dev/null +++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-ndrchk.robot @@ -0,0 +1,192 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.InterfaceUtil +| Library | resources.libraries.python.NodePath +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK +| ... | NIC_Intel-X520-DA2 | ETH | L2XCFWD | BASE | L2XCBASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance ndrchk test +| ... +| Documentation | *Reference NDR throughput L2XC verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-NDR value is periodically updated acording to +| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long +| ... | performance tests for the same DUT configuration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 +| ... | and static payload. MAC addresses are matching MAC addresses of the +| ... | TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test at 2x 5.9mpps. +| | [Tags] | 64B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${64} +| | ${rate}= | Set Variable | 5.9mpps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc02-1518B-1t1c-eth-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc03-9000B-1t1c-eth-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 1T1C | STHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc04-64B-2t2c-eth-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test at 2x 10.4mpps. +| | [Tags] | 64B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${64} +| | ${rate}= | Set Variable | 10.4mpps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc05-1518B-2t2c-eth-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc06-9000B-2t2c-eth-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc07-64B-4t4c-eth-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 64 Byte +| | ... | frames using single trial throughput test at 2x 10.4mpps. +| | [Tags] | 64B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${64} +| | ${rate}= | Set Variable | 10.4mpps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc08-1518B-4t4c-eth-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 1518 Byte +| | ... | frames using single trial throughput test at 2x 812743pps. +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${1518} +| | ${rate}= | Set Variable | 812743pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} + +| tc09-9000B-4t4c-eth-l2xcbase-ndrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 9000 Byte +| | ... | frames using single trial throughput test at 2x 138580pps. +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ${framesize}= | Set Variable | ${9000} +| | ${rate}= | Set Variable | 138580pps +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} +| | ... | ${framesize} | ${traffic_profile} diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-ndrpdrdisc.robot new file mode 100644 index 0000000000..4c0e0a18b2 --- /dev/null +++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-ndrpdrdisc.robot @@ -0,0 +1,483 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.InterfaceUtil +| Library | resources.libraries.python.NodePath +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-X520-DA2 | ETH | L2XCFWD | BASE | L2XCBASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput L2XC test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 253 flows per flow-group) with all packets +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static +| ... | payload. MAC addresses are matching MAC addresses of the TG node +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc02-64B-1t1c-eth-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc03-1518B-1t1c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc04-1518B-1t1c-eth-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc05-9000B-1t1c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc06-9000B-1t1c-eth-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc07-64B-2t2c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc08-64B-2t2c-eth-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc09-1518B-2t2c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc10-1518B-2t2c-eth-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc11-9000B-2t2c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc12-9000B-2t2c-eth-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc13-64B-4t4c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc14-64B-4t4c-eth-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc15-1518B-4t4c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc16-1518B-4t4c-eth-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc17-9000B-4t4c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc18-9000B-4t4c-eth-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| tc19-IMIX-1t1c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | [Tags] | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | IMIX_v4_1 +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc20-IMIX-1t1c-eth-l2xcbase-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | IMIX_v4_1 +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-pdrchk.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-pdrchk.robot new file mode 100644 index 0000000000..72589f6ca1 --- /dev/null +++ b/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-pdrchk.robot @@ -0,0 +1,184 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.InterfaceUtil +| Library | resources.libraries.python.NodePath +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PDRCHK +| ... | NIC_Intel-X520-DA2 | ETH | L2XCFWD | BASE | L2XCBASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| Test Teardown | Tear down performance pdrchk test +| ... +| Documentation | *Reference PDR throughput L2XC verify test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In short performance tests, TG verifies +| ... | DUTs' throughput at ref-PDR (reference Non Drop Rate) with zero packet +| ... | loss tolerance. Ref-PDR value is periodically updated acording to +| ... | formula: ref-PDR = 0.9x PDR, where PDR is found in RFC2544 long +| ... | performance tests for the same DUT configuration. Test packets are +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 +| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with +| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 +| ... | and static payload. MAC addresses are matching MAC addresses of the +| ... | TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| Check PDR for L2 xconnect +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with ${wt} thread, ${wt} phy core,\ +| | ... | ${rxq} receive queue per NIC port. +| | ... | [Ver] Verify ref-PDR for ${framesize} Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Arguments] | ${framesize} | ${rate} | ${wt} | ${rxq} +| | ... +| | # Test Variables required for test and test teardown +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${rate} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Traffic should pass with partial loss | ${perf_trial_duration} +| | ... | ${rate} | ${framesize} | ${traffic_profile} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2xcbase-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for L2 xconnect +| | framesize=${64} | rate=5.9mpps | wt=1 | rxq=1 + +| tc02-1518B-1t1c-eth-l2xcbase-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for L2 xconnect +| | framesize=${1518} | rate=812743pps | wt=1 | rxq=1 + +| tc03-9000B-1t1c-eth-l2xcbase-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 1T1C | STHREAD +| | ... +| | [Template] | Check PDR for L2 xconnect +| | framesize=${9000} | rate=138580pps | wt=1 | rxq=1 + +| tc04-64B-2t2c-eth-l2xcbase-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for L2 xconnect +| | framesize=${64} | rate=10.4mpps | wt=2 | rxq=1 + +| tc05-1518B-2t2c-eth-l2xcbase-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for L2 xconnect +| | framesize=${1518} | rate=812743pps | wt=2 | rxq=1 + +| tc06-9000B-2t2c-eth-l2xcbase-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 2T2C | MTHREAD +| | ... +| | [Template] | Check PDR for L2 xconnect +| | framesize=${9000} | rate=100000pps | wt=2 | rxq=1 + +| tc07-64B-4t4c-eth-l2xcbase-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for L2 xconnect +| | framesize=${64} | rate=10.4mpps | wt=4 | rxq=2 + +| tc08-1518B-4t4c-eth-l2xcbase-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for L2 xconnect +| | framesize=${1518} | rate=812743pps | wt=4 | rxq=2 + +| tc09-9000B-4t4c-eth-l2xcbase-pdrchk +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ +| | ... | throughput test at 2x ${rate}. +| | ... +| | [Tags] | 9000B | 4T4C | MTHREAD +| | ... +| | [Template] | Check PDR for L2 xconnect +| | framesize=${9000} | rate=138580pps | wt=4 | rxq=2 diff --git a/tests/vpp/perf/l2/10ge2p1x710-eth-l2bdbasemaclrn-ndrpdrdisc.robot b/tests/vpp/perf/l2/10ge2p1x710-eth-l2bdbasemaclrn-ndrpdrdisc.robot new file mode 100644 index 0000000000..166e1c7a4f --- /dev/null +++ b/tests/vpp/perf/l2/10ge2p1x710-eth-l2bdbasemaclrn-ndrpdrdisc.robot @@ -0,0 +1,274 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-X710 | ETH | L2BDMACLRN | BASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput L2BD test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge-\ +| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC +| ... | X710 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using either binary search or linear search\ +| ... | algorithms with configured starting rate and final step that determines\ +| ... | throughput measurement resolution. Test packets are generated by TG on\ +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\ +| ... | (flow-group per direction, 253 flows per flow-group) with all packets\ +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\ +| ... | payload. MAC addresses are matching MAC addresses of the TG node\ +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X710 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| L2 Bridge Domain NDR Binary Search +| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | Add PCI devices to DUTs in 3-node single link topology +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs +| | Apply startup configuration on all VPP DUTs +| | Initialize L2 bridge domain in 3-node circular topology +| | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| L2 Bridge Domain PDR Binary Search +| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | Add PCI devices to DUTs in 3-node single link topology +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs +| | Apply startup configuration on all VPP DUTs +| | Initialize L2 bridge domain in 3-node circular topology +| | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=1 | rxq=1 +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc02-64B-1t1c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=1 | rxq=1 +| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc03-1518B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=1 | rxq=1 +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc04-1518B-1t1c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=1 | rxq=1 +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc05-9000B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=1 | rxq=1 +| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc06-9000B-1t1c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=1 | rxq=1 +| | [Tags] | 9000B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc07-64B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=2 | rxq=1 +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc08-64B-2t2c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=2 | rxq=1 +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc09-1518B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=2 | rxq=1 +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc10-1518B-2t2c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=2 | rxq=1 +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc11-9000B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=2 | rxq=1 +| | [Tags] | 9000B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc12-9000B-2t2c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=2 | rxq=1 +| | [Tags] | 9000B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc13-64B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=4 | rxq=2 +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc14-64B-4t4c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=4 | rxq=2 +| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc15-1518B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=4 | rxq=2 +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc16-1518B-4t4c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=4 | rxq=2 +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc17-9000B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=4 | rxq=2 +| | [Tags] | 9000B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc18-9000B-4t4c-eth-l2bdbasemaclrn-pdrdisc +| | ... | framesize=${9000} | min_rate=${10000} | wt=4 | rxq=2 +| | [Tags] | 9000B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Template] | L2 Bridge Domain PDR Binary Search diff --git a/tests/vpp/perf/l2/40ge2p1vic1385-eth-l2bdbasemaclrn-ndrpdrdisc.robot b/tests/vpp/perf/l2/40ge2p1vic1385-eth-l2bdbasemaclrn-ndrpdrdisc.robot new file mode 100644 index 0000000000..6d39fc169a --- /dev/null +++ b/tests/vpp/perf/l2/40ge2p1vic1385-eth-l2bdbasemaclrn-ndrpdrdisc.robot @@ -0,0 +1,352 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.NodePath +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Cisco-VIC-1385 | ETH | L2BDMACLRN | BASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Cisco-VIC-1385 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput L2BD test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- +| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p40GE NIC +| ... | NIC_Cisco-VIC-1385. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 253 flows per flow-group) with all packets +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static +| ... | payload. MAC addresses are matching MAC addresses of the TG node +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# XL710-DA2 (TG) bandwidth limit ~49Gbps/2=24.5Gbps +| ${s_24.5G} | ${24500000000} +# XL710-DA2 Mpps (TG) limit 37.5Mpps/2=18.75Mpps +| ${s_18.75Mpps} | ${18750000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\ +| | ... | 18.75Mpps rate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ... +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Set Variable | ${s_18.75Mpps} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc02-64B-1t1c-eth-l2bdbasemaclrn-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at\ +| | ... | 18.75Mpps rate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Set Variable | ${s_18.75Mpps} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} +| | ... | ${perf_pdr_loss_acceptance_type} + +| tc03-1518B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\ +| | ... | 24.5G rate, step 10kpps. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ... +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc05-9000B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\ +| | ... | 24.5G rate, step 10kpps. +| | ... +| | [Tags] | 9000B | 1T1C | STHREAD | NDRDISC +| | ... +| | ${framesize}= | Set Variable | ${9000} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc07-64B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\ +| | ... | 18.75Mpps rate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ... +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Set Variable | ${s_18.75Mpps} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc08-64B-2t2c-eth-l2bdbasemaclrn-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at\ +| | ... | 18.75Mpps rate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | PDR | SKIP_PATCH +| | ... +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Set Variable | ${s_18.75Mpps} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} +| | ... | ${perf_pdr_loss_acceptance_type} + +| tc09-1518B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\ +| | ... | 24.5G rate, step 10kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ... +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc13-64B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\ +| | ... | 18.75Mpps rate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | ... +| | ${framesize}= | Set Variable | ${64} +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Set Variable | ${s_18.75Mpps} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc15-1518B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\ +| | ... | 24.5G rate, step 10kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ... +| | ${framesize}= | Set Variable | ${1518} +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc19-IMIX-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at\ +| | ... | 24.5G rate, step 100kpps. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC +| | ... +| | ${framesize}= | Set Variable | IMIX_v4_1 +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc20-IMIX-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 2 thread, 2 phy core,\ +| | ... | 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at\ +| | ... | 24.5G rate, step 100kpps. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ... +| | ${framesize}= | Set Variable | IMIX_v4_1 +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc21-IMIX-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with 4 thread, 4 phy core,\ +| | ... | 2 receive queue per NIC port. +| | ... | [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at\ +| | ... | 24.5G rate, step 100kpps. +| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B) +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ... +| | ${framesize}= | Set Variable | IMIX_v4_1 +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 bridge domain in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} diff --git a/tests/vpp/perf/l2/40ge2p1xl710-eth-l2bdbasemaclrn-ndrpdrdisc.robot b/tests/vpp/perf/l2/40ge2p1xl710-eth-l2bdbasemaclrn-ndrpdrdisc.robot new file mode 100644 index 0000000000..595bc029ce --- /dev/null +++ b/tests/vpp/perf/l2/40ge2p1xl710-eth-l2bdbasemaclrn-ndrpdrdisc.robot @@ -0,0 +1,232 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.NodePath +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-XL710 | ETH | L2BDMACLRN | BASE +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-XL710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput L2BD test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge-\ +| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p40GE NIC\ +| ... | XL710-DA2 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using either binary search or linear search\ +| ... | algorithms with configured starting rate and final step that determines\ +| ... | throughput measurement resolution. Test packets are generated by TG on\ +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\ +| ... | (flow-group per direction, 253 flows per flow-group) with all packets\ +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\ +| ... | payload. MAC addresses are matching MAC addresses of the TG node\ +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps +| ${s_24.5G} | ${24500000000} +# XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps +| ${s_18.75Mpps} | ${18750000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Keywords *** +| L2 Bridge Domain NDR Binary Search BW limit +| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq} | ${s_limit} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | Add PCI devices to DUTs in 3-node single link topology +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs +| | Apply startup configuration on all VPP DUTs +| | Initialize L2 bridge domain in 3-node circular topology +| | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| L2 Bridge Domain NDR Binary Search +| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq} | ${s_limit} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${max_rate}= | Set Variable | ${s_limit} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | Add PCI devices to DUTs in 3-node single link topology +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs +| | Apply startup configuration on all VPP DUTs +| | Initialize L2 bridge domain in 3-node circular topology +| | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| L2 Bridge Domain PDR Binary Search BW limit +| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq} | ${s_limit} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | Add PCI devices to DUTs in 3-node single link topology +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs +| | Apply startup configuration on all VPP DUTs +| | Initialize L2 bridge domain in 3-node circular topology +| | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +| L2 Bridge Domain PDR Binary Search +| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq} | ${s_limit} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | Add PCI devices to DUTs in 3-node single link topology +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs +| | Apply startup configuration on all VPP DUTs +| | Initialize L2 bridge domain in 3-node circular topology +| | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=1 | rxq=1 +| | ... | s_limit=${s_18.75Mpps} +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\ +| | ... | 18.75Mpps rate, step 100kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc03-1518B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=1 | rxq=1 +| | ... | s_limit=${s_24.5G} +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\ +| | ... | 24.5G rate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search BW limit + +| tc07-64B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=2 | rxq=1 +| | ... | s_limit=${s_18.75Mpps} +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\ +| | ... | 18.75Mpps rate, step 100kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc09-1518B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=2 | rxq=1 +| | ... | s_limit=${s_24.5G} +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\ +| | ... | 24.5G rate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search BW limit + +| tc13-64B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${64} | min_rate=${100000} | wt=4 | rxq=2 +| | ... | s_limit=${s_18.75Mpps} +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at\ +| | ... | 18.75Mpps rate, step 100kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc15-1518B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=${1518} | min_rate=${10000} | wt=4 | rxq=2 +| | ... | s_limit=${s_24.5G} +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at\ +| | ... | 24.5G rate, step 10kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search BW limit + +| tc19-IMIX-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=IMIX_v4_1 | min_rate=${100000} | wt=1 | rxq=1 +| | ... | s_limit=${s_24.5G} +| | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for IMIX_v4_1 frames using binary search start at\ +| | ... | 24.5G rate, step 100kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search BW limit + +| tc20-IMIX-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=IMIX_v4_1 | min_rate=${100000} | wt=2 | rxq=1 +| | ... | s_limit=${s_24.5G} +| | [Tags] | IMIX | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for IMIX_v4_1 frames using binary search start at\ +| | ... | 24.5G rate, step 100kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search BW limit + +| tc21-IMIX-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | framesize=IMIX_v4_1 | min_rate=${100000} | wt=4 | rxq=2 +| | ... | s_limit=${s_24.5G} +| | [Tags] | IMIX | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for IMIX_v4_1 frames using binary search start at\ +| | ... | 24.5G rate, step 100kpps. +| | [Template] | L2 Bridge Domain NDR Binary Search BW limit diff --git a/tests/vpp/perf/l2/40ge2p1xl710-eth-l2xcbase-ndrpdrdisc.robot b/tests/vpp/perf/l2/40ge2p1xl710-eth-l2xcbase-ndrpdrdisc.robot new file mode 100644 index 0000000000..4c6f279e8d --- /dev/null +++ b/tests/vpp/perf/l2/40ge2p1xl710-eth-l2xcbase-ndrpdrdisc.robot @@ -0,0 +1,251 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Library | resources.libraries.python.InterfaceUtil +| Library | resources.libraries.python.NodePath +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-XL710 | ETH | L2XCFWD | BASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-XL710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Documentation | *RFC2544: Pkt throughput L2XC test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. DUT1 and DUT2 tested with 2p40GE NIC XL710 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 253 flows per flow-group) with all packets +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static +| ... | payload. MAC addresses are matching MAC addresses of the TG node +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# XL710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps +| ${s_24.5G} | ${24500000000} +# XL710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps +| ${s_18.75Mpps} | ${18750000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 18.75Mpps rate, step 100kpps. +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Set Variable | ${s_18.75Mpps} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc03-1518B-1t1c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 24.5G rate, step 10kpps. +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | 1518 +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc07-64B-2t2c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 18.75Mpps rate, step 100kpps. +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Set Variable | ${s_18.75Mpps} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc09-1518B-2t2c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 24.5G rate, step 10kpps. +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | 1518 +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc13-64B-4t4c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 18.75Mpps rate, step 100kpps. +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | ${framesize}= | Set Variable | 64 +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Set Variable | ${s_18.75Mpps} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc15-1518B-4t4c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 24.5G rate, step 10kpps. +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | 1518 +| | ${min_rate}= | Set Variable | ${10000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc19-IMIX-1t1c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size +| | ... | using binary search start at 24.5G rate, step 100kpps. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC +| | ${framesize}= | Set Variable | IMIX_v4_1 +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${353.83333} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc20-IMIX-2t2c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 2 thread, 2 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size +| | ... | using binary search start at 24.5G rate, step 100kpps. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | [Tags] | IMIX | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | IMIX_v4_1 +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${353.83333} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| tc21-IMIX-4t4c-eth-l2xcbase-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs L2XC switching config with 4 thread, 4 phy core, \ +| | ... | 2 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size +| | ... | using binary search start at 24.5G rate, step 100kpps. +| | ... | IMIX_v4_1 = (28x64B;16x570B;4x1518B) +| | [Tags] | IMIX | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | ${framesize}= | Set Variable | IMIX_v4_1 +| | ${min_rate}= | Set Variable | ${100000} +| | ${max_rate}= | Calculate pps | ${s_24.5G} | ${353.83333} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Add no multi seg to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | And Initialize L2 xconnect in 3-node circular topology +| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} +| | ... | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} |