diff options
Diffstat (limited to 'tests/vpp/perf/l2')
6 files changed, 0 insertions, 1297 deletions
diff --git a/tests/vpp/perf/l2/10ge2p1x520-dot1ad-l2xcbase-ndrchk.robot b/tests/vpp/perf/l2/10ge2p1x520-dot1ad-l2xcbase-ndrchk.robot deleted file mode 100644 index 3f4f0b23f3..0000000000 --- a/tests/vpp/perf/l2/10ge2p1x520-dot1ad-l2xcbase-ndrchk.robot +++ /dev/null @@ -1,279 +0,0 @@ -# Copyright (c) 2017 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance/performance_setup.robot -| Resource | resources/libraries/robot/l2/tagging.robot -| ... -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK -| ... | NIC_Intel-X520-DA2 | L2XCFWD | BASE | DOT1AD -| ... -| Suite Setup | Set up 3-node performance topology with DUT's NIC model -| ... | L2 | Intel-X520-DA2 -| Suite Teardown | Tear down 3-node performance topology -| ... -| Test Setup | Set up performance test -| Test Teardown | Tear down performance ndrchk test -| ... -| Documentation | *Reference NDR throughput L2XC with 802.1ad verify test cases* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 xconnect. -| ... | 802.1ad tagging is applied on link between DUT1 and DUT2 with inner 4B -| ... | vlan tag (id=100) and outer 4B vlan tag (id=200). -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- -| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. -| ... | *[Ver] TG verification:* In short performance tests, TG verifies -| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet -| ... | loss tolerance. Ref-NDR value is periodically updated acording to -| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long -| ... | performance tests for the same DUT configuration. Test packets are -| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 -| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with -| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 -| ... | and static payload. MAC addresses are matching MAC addresses of the -| ... | TG node interfaces. -| ... | *[Ref] Applicable standard specifications:* RFC2544. - -*** Variables *** -| ${subid}= | 10 -| ${outer_vlan_id}= | 100 -| ${inner_vlan_id}= | 200 -| ${type_subif}= | two_tags -| ${tag_rewrite}= | pop-2 -# Traffic profile: -| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 - -*** Test Cases *** -| tc01-64B-1t1c-dot1ad-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte -| | ... | frames using single trial throughput test at 2x 4.0mpps. -| | [Tags] | 64B | 1T1C | STHREAD -| | ${framesize}= | Set Variable | ${64} -| | ${rate}= | Set Variable | 4.0mpps -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc02-1514B-1t1c-dot1ad-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1514 Byte -| | ... | frames using single trial throughput test at 2x 810635pps. -| | [Tags] | 1514B | 1T1C | STHREAD -| | ${framesize}= | Set Variable | ${1514} -| | ${rate}= | Set Variable | 810635pps -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc03-9000B-1t1c-dot1ad-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte -| | ... | frames using single trial throughput test at 2x 138458pps. -| | [Tags] | 9000B | 1T1C | STHREAD -| | ${framesize}= | Set Variable | ${9000} -| | ${rate}= | Set Variable | 138458pps -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc04-64B-2t2c-dot1ad-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 2 thread, 2 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte -| | ... | frames using single trial throughput test at 2x 8.2mpps. -| | [Tags] | 64B | 2T2C | MTHREAD -| | ${framesize}= | Set Variable | ${64} -| | ${rate}= | Set Variable | 8.2mpps -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc05-1514B-2t2c-dot1ad-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 2 thread, 2 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1514 Byte -| | ... | frames using single trial throughput test at 2x 810635pps. -| | [Tags] | 1514B | 2T2C | MTHREAD -| | ${framesize}= | Set Variable | ${1514} -| | ${rate}= | Set Variable | 810635pps -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc06-9000B-2t2c-dot1ad-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 2 thread, 2 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte -| | ... | frames using single trial throughput test at 2x 138458pps. -| | [Tags] | 9000B | 2T2C | MTHREAD -| | ${framesize}= | Set Variable | ${9000} -| | ${rate}= | Set Variable | 138458pps -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc07-64B-4t4c-dot1ad-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 4 thread, 4 phy core, \ -| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte -| | ... | frames using single trial throughput test at 2x 8.6mpps. -| | [Tags] | 64B | 4T4C | MTHREAD -| | ${framesize}= | Set Variable | ${64} -| | ${rate}= | Set Variable | 8.6mpps -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc08-1514B-4t4c-dot1ad-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 4 thread, 4 phy core, \ -| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 1514 Byte -| | ... | frames using single trial throughput test at 2x 810635pps. -| | [Tags] | 1514B | 4T4C | MTHREAD -| | ${framesize}= | Set Variable | ${1514} -| | ${rate}= | Set Variable | 810635pps -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc09-9000B-4t4c-dot1ad-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC with 802.1ad config with 4 thread, 4 phy core, \ -| | ... | 2 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte -| | ... | frames using single trial throughput test at 2x 138458pps. -| | [Tags] | 9000B | 4T4C | MTHREAD -| | ${framesize}= | Set Variable | ${9000} -| | ${rate}= | Set Variable | 138458pps -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | ... | ${outer_vlan_id} | ${inner_vlan_id} | ${type_subif} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} diff --git a/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-ndrchk.robot b/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-ndrchk.robot deleted file mode 100644 index ae3f2d4364..0000000000 --- a/tests/vpp/perf/l2/10ge2p1x520-dot1q-l2xcbase-ndrchk.robot +++ /dev/null @@ -1,266 +0,0 @@ -# Copyright (c) 2017 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance/performance_setup.robot -| Resource | resources/libraries/robot/l2/tagging.robot -| ... -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK -| ... | NIC_Intel-X520-DA2 | L2XCFWD | BASE | DOT1Q -| ... -| Suite Setup | Set up 3-node performance topology with DUT's NIC model -| ... | L2 | Intel-X520-DA2 -| Suite Teardown | Tear down 3-node performance topology -| ... -| Test Setup | Set up performance test -| Test Teardown | Tear down performance ndrchk test -| ... -| Documentation | *Reference NDR throughput L2XC with 802.1q verify test cases* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. 802.1q -| ... | tagging is applied on link between DUT1 and DUT2. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- -| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. -| ... | *[Ver] TG verification:* In short performance tests, TG verifies -| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet -| ... | loss tolerance. Ref-NDR value is periodically updated acording to -| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long -| ... | performance tests for the same DUT configuration. Test packets are -| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 -| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with -| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 -| ... | and static payload. MAC addresses are matching MAC addresses of the -| ... | TG node interfaces. -| ... | *[Ref] Applicable standard specifications:* RFC2544. - -*** Variables *** -| ${subid}= | 10 -| ${tag_rewrite}= | pop-1 -# Traffic profile: -| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 - -*** Test Cases *** -| tc01-64B-1t1c-dot1q-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte -| | ... | frames using single trial throughput test at 2x 4.0mpps. -| | [Tags] | 64B | 1T1C | STHREAD -| | ${framesize}= | Set Variable | ${64} -| | ${rate}= | Set Variable | 4.0mpps -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc02-1518B-1t1c-dot1q-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte -| | ... | frames using single trial throughput test at 2x 720000pps. -| | [Tags] | 1518B | 1T1C | STHREAD -| | ${framesize}= | Set Variable | ${1518} -| | ${rate}= | Set Variable | 720000pps -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc03-9000B-1t1c-dot1q-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte -| | ... | frames using single trial throughput test at 2x 120000pps. -| | [Tags] | 9000B | 1T1C | STHREAD -| | ${framesize}= | Set Variable | ${9000} -| | ${rate}= | Set Variable | 120000pps -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc04-64B-2t2c-dot1q-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte -| | ... | frames using single trial throughput test at 2x 8.1mpps. -| | [Tags] | 64B | 2T2C | MTHREAD -| | ${framesize}= | Set Variable | ${64} -| | ${rate}= | Set Variable | 8.1mpps -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc05-1518B-2t2c-dot1q-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte -| | ... | frames using single trial throughput test at 2x 720000pps. -| | [Tags] | 1518B | 2T2C | MTHREAD -| | ${framesize}= | Set Variable | ${1518} -| | ${rate}= | Set Variable | 720000pps -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc06-9000B-2t2c-dot1q-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte -| | ... | frames using single trial throughput test at 2x 120000pps. -| | [Tags] | 9000B | 2T2C | MTHREAD -| | ${framesize}= | Set Variable | ${9000} -| | ${rate}= | Set Variable | 120000pps -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc07-64B-4t4c-dot1q-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 64 Byte -| | ... | frames using single trial throughput test at 2x 10.3mpps. -| | [Tags] | 64B | 4T4C | MTHREAD -| | ${framesize}= | Set Variable | ${64} -| | ${rate}= | Set Variable | 10.3mpps -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc08-1518B-4t4c-dot1q-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 1518 Byte -| | ... | frames using single trial throughput test at 2x 720000pps. -| | [Tags] | 1518B | 4T4C | MTHREAD -| | ${framesize}= | Set Variable | ${1518} -| | ${rate}= | Set Variable | 720000pps -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc09-9000B-4t4c-dot1q-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 9000 Byte -| | ... | frames using single trial throughput test at 2x 120000pps. -| | [Tags] | 9000B | 4T4C | MTHREAD -| | ${framesize}= | Set Variable | ${9000} -| | ${rate}= | Set Variable | 120000pps -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Set interfaces in path in 3-node circular topology up -| | When Initialize VLAN dot1q sub-interfaces in 3-node circular topology -| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid} -| | And Configure L2 tag rewrite method on interfaces -| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2} -| | ... | ${tag_rewrite} -| | And Connect interfaces and VLAN sub-interfaces using L2XC -| | ... | ${dut1} | ${dut1_if1} | ${subif_index_1} -| | ... | ${dut2} | ${dut2_if2} | ${subif_index_2} -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-ndrchk.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-ndrchk.robot deleted file mode 100644 index 351216235a..0000000000 --- a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-ndrchk.robot +++ /dev/null @@ -1,192 +0,0 @@ -# Copyright (c) 2017 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance/performance_setup.robot -| Library | resources.libraries.python.NodePath -| ... -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK -| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | BASE | L2BDBASE -| ... -| Suite Setup | Set up 3-node performance topology with DUT's NIC model -| ... | L2 | Intel-X520-DA2 -| Suite Teardown | Tear down 3-node performance topology -| ... -| Test Setup | Set up performance test -| Test Teardown | Tear down performance ndrchk test -| ... -| Documentation | *Reference NDR throughput L2BD verify test cases* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- -| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC -| ... | X520 Niantic by Intel. -| ... | *[Ver] TG verification:* In short performance tests, TG verifies -| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet -| ... | loss tolerance. Ref-NDR value is periodically updated acording to -| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long -| ... | performance tests for the same DUT configuration. Test packets are -| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 -| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with -| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 -| ... | and static payload. MAC addresses are matching MAC addresses of the -| ... | TG node interfaces. -| ... | *[Ref] Applicable standard specifications:* RFC2544. - -*** Variables *** -# Traffic profile: -| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 - -*** Test Cases *** -| tc01-64B-1t1c-eth-l2bdbasemaclrn-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte -| | ... | frames using single trial throughput test at 2x 4.0mpps. -| | [Tags] | 64B | 1T1C | STHREAD -| | ${framesize}= | Set Variable | ${64} -| | ${rate}= | Set Variable | 4.0mpps -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 bridge domain in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc02-1518B-1t1c-eth-l2bdbasemaclrn-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte -| | ... | frames using single trial throughput test at 2x 812743pps. -| | [Tags] | 1518B | 1T1C | STHREAD -| | ${framesize}= | Set Variable | ${1518} -| | ${rate}= | Set Variable | 812743pps -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 bridge domain in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc03-9000B-1t1c-eth-l2bdbasemaclrn-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte -| | ... | frames using single trial throughput test at 2x 138580pps. -| | [Tags] | 9000B | 1T1C | STHREAD -| | ${framesize}= | Set Variable | ${9000} -| | ${rate}= | Set Variable | 138580pps -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 bridge domain in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc04-64B-2t2c-eth-l2bdbasemaclrn-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte -| | ... | frames using single trial throughput test at 2x 9.4mpps. -| | [Tags] | 64B | 2T2C | MTHREAD -| | ${framesize}= | Set Variable | ${64} -| | ${rate}= | Set Variable | 9.4mpps -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 bridge domain in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc05-1518B-2t2c-eth-l2bdbasemaclrn-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte -| | ... | frames using single trial throughput test at 2x 812743pps. -| | [Tags] | 1518B | 2T2C | MTHREAD -| | ${framesize}= | Set Variable | ${1518} -| | ${rate}= | Set Variable | 812743pps -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 bridge domain in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc06-9000B-2t2c-eth-l2bdbasemaclrn-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte -| | ... | frames using single trial throughput test at 2x 138580pps. -| | [Tags] | 9000B | 2T2C | MTHREAD -| | ${framesize}= | Set Variable | ${9000} -| | ${rate}= | Set Variable | 138580pps -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 bridge domain in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc07-64B-4t4c-eth-l2bdbasemaclrn-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 64 Byte -| | ... | frames using single trial throughput test at 2x 10.4mpps. -| | [Tags] | 64B | 4T4C | MTHREAD -| | ${framesize}= | Set Variable | ${64} -| | ${rate}= | Set Variable | 10.4mpps -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 bridge domain in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc08-1518B-4t4c-eth-l2bdbasemaclrn-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 1518 Byte -| | ... | frames using single trial throughput test at 2x 812743pps. -| | [Tags] | 1518B | 4T4C | MTHREAD -| | ${framesize}= | Set Variable | ${1518} -| | ${rate}= | Set Variable | 812743pps -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 bridge domain in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc09-9000B-4t4c-eth-l2bdbasemaclrn-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 9000 Byte -| | ... | frames using single trial throughput test at 2x 138580pps. -| | [Tags] | 9000B | 4T4C | MTHREAD -| | ${framesize}= | Set Variable | ${9000} -| | ${rate}= | Set Variable | 138580pps -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 bridge domain in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-pdrchk.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-pdrchk.robot deleted file mode 100644 index 257efc93f6..0000000000 --- a/tests/vpp/perf/l2/10ge2p1x520-eth-l2bdbasemaclrn-pdrchk.robot +++ /dev/null @@ -1,184 +0,0 @@ -# Copyright (c) 2017 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance/performance_setup.robot -| Library | resources.libraries.python.NodePath -| ... -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PDRCHK -| ... | NIC_Intel-X520-DA2 | ETH | L2BDMACLRN | BASE | L2BDBASE -| ... -| Suite Setup | Set up 3-node performance topology with DUT's NIC model -| ... | L2 | Intel-X520-DA2 -| Suite Teardown | Tear down 3-node performance topology -| ... -| Test Setup | Set up performance test -| Test Teardown | Tear down performance pdrchk test -| ... -| Documentation | *Reference PDR throughput L2BD verify test cases* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge- -| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC -| ... | X520 Niantic by Intel. -| ... | *[Ver] TG verification:* In short performance tests, TG verifies -| ... | DUTs' throughput at ref-PDR (reference Non Drop Rate) with zero packet -| ... | loss tolerance. Ref-PDR value is periodically updated acording to -| ... | formula: ref-PDR = 0.9x PDR, where PDR is found in RFC2544 long -| ... | performance tests for the same DUT configuration. Test packets are -| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 -| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with -| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 -| ... | and static payload. MAC addresses are matching MAC addresses of the -| ... | TG node interfaces. -| ... | *[Ref] Applicable standard specifications:* RFC2544. - -*** Variables *** -# Traffic profile: -| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 - -*** Keywords *** -| Check PDR for L2 bridge domain -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with ${wt} thread, ${wt} phy core,\ -| | ... | ${rxq} receive queue per NIC port. -| | ... | [Ver] Verify ref-PDR for ${framesize} Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Arguments] | ${framesize} | ${rate} | ${wt} | ${rxq} -| | ... -| | # Test Variables required for test and test teardown -| | Set Test Variable | ${framesize} -| | Set Test Variable | ${rate} -| | ${get_framesize}= | Get Frame Size | ${framesize} -| | ... -| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Run Keyword If | ${get_framesize} < ${1522} -| | ... | Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 bridge domain in 3-node circular topology -| | Then Traffic should pass with partial loss | ${perf_trial_duration} -| | ... | ${rate} | ${framesize} | ${traffic_profile} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -*** Test Cases *** -| tc01-64B-1t1c-eth-l2bdbasemaclrn-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Verify ref-PDR for 64 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 64B | 1T1C | STHREAD -| | ... -| | [Template] | Check PDR for L2 bridge domain -| | framesize=${64} | rate=4.0mpps | wt=1 | rxq=1 - -| tc02-1518B-1t1c-eth-l2bdbasemaclrn-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Verify ref-PDR for 1518 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 1518B | 1T1C | STHREAD -| | ... -| | [Template] | Check PDR for L2 bridge domain -| | framesize=${1518} | rate=772105pps | wt=1 | rxq=1 - -| tc03-9000B-1t1c-eth-l2bdbasemaclrn-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Verify ref-PDR for 9000 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 9000B | 1T1C | STHREAD -| | ... -| | [Template] | Check PDR for L2 bridge domain -| | framesize=${9000} | rate=110000pps | wt=1 | rxq=1 - -| tc04-64B-2t2c-eth-l2bdbasemaclrn-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 2 thread, 2 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Verify ref-PDR for 64 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 64B | 2T2C | MTHREAD -| | ... -| | [Template] | Check PDR for L2 bridge domain -| | framesize=${64} | rate=9.4mpps | wt=2 | rxq=1 - -| tc05-1518B-2t2c-eth-l2bdbasemaclrn-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 2 thread, 2 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Verify ref-PDR for 1518 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 1518B | 2T2C | MTHREAD -| | ... -| | [Template] | Check PDR for L2 bridge domain -| | framesize=${1518} | rate=812743pps | wt=2 | rxq=1 - -| tc06-9000B-2t2c-eth-l2bdbasemaclrn-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 2 thread, 2 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Verify ref-PDR for 9000 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 9000B | 2T2C | MTHREAD -| | ... -| | [Template] | Check PDR for L2 bridge domain -| | framesize=${9000} | rate=100000pps | wt=2 | rxq=1 - -| tc07-64B-4t4c-eth-l2bdbasemaclrn-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 4 thread, 4 phy core,\ -| | ... | 2 receive queue per NIC port. -| | ... | [Ver] Verify ref-PDR for 64 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 64B | 4T4C | MTHREAD -| | ... -| | [Template] | Check PDR for L2 bridge domain -| | framesize=${64} | rate=10.4mpps | wt=4 | rxq=2 - -| tc08-1518B-4t4c-eth-l2bdbasemaclrn-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 4 thread, 4 phy core,\ -| | ... | 2 receive queue per NIC port. -| | ... | [Ver] Verify ref-PDR for 1518 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 1518B | 4T4C | MTHREAD -| | ... -| | [Template] | Check PDR for L2 bridge domain -| | framesize=${1518} | rate=812743pps | wt=4 | rxq=2 - -| tc09-9000B-4t4c-eth-l2bdbasemaclrn-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2BD config with 4 thread, 4 phy core,\ -| | ... | 2 receive queue per NIC port. -| | ... | [Ver] Verify ref-PDR for 9000 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 9000B | 4T4C | MTHREAD -| | ... -| | [Template] | Check PDR for L2 bridge domain -| | framesize=${9000} | rate=138580pps | wt=4 | rxq=2 diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-ndrchk.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-ndrchk.robot deleted file mode 100644 index 115df06e97..0000000000 --- a/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-ndrchk.robot +++ /dev/null @@ -1,192 +0,0 @@ -# Copyright (c) 2017 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance/performance_setup.robot -| Library | resources.libraries.python.InterfaceUtil -| Library | resources.libraries.python.NodePath -| ... -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRCHK -| ... | NIC_Intel-X520-DA2 | ETH | L2XCFWD | BASE | L2XCBASE -| ... -| Suite Setup | Set up 3-node performance topology with DUT's NIC model -| ... | L2 | Intel-X520-DA2 -| Suite Teardown | Tear down 3-node performance topology -| ... -| Test Setup | Set up performance test -| Test Teardown | Tear down performance ndrchk test -| ... -| Documentation | *Reference NDR throughput L2XC verify test cases* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- -| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. -| ... | *[Ver] TG verification:* In short performance tests, TG verifies -| ... | DUTs' throughput at ref-NDR (reference Non Drop Rate) with zero packet -| ... | loss tolerance. Ref-NDR value is periodically updated acording to -| ... | formula: ref-NDR = 0.9x NDR, where NDR is found in RFC2544 long -| ... | performance tests for the same DUT configuration. Test packets are -| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 -| ... | flow-groups (flow-group per direction, 253 flows per flow-group) with -| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 -| ... | and static payload. MAC addresses are matching MAC addresses of the -| ... | TG node interfaces. -| ... | *[Ref] Applicable standard specifications:* RFC2544. - -*** Variables *** -# Traffic profile: -| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 - -*** Test Cases *** -| tc01-64B-1t1c-eth-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte -| | ... | frames using single trial throughput test at 2x 5.5mpps. -| | [Tags] | 64B | 1T1C | STHREAD -| | ${framesize}= | Set Variable | ${64} -| | ${rate}= | Set Variable | 5.5mpps -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 xconnect in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc02-1518B-1t1c-eth-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte -| | ... | frames using single trial throughput test at 2x 812743pps. -| | [Tags] | 1518B | 1T1C | STHREAD -| | ${framesize}= | Set Variable | ${1518} -| | ${rate}= | Set Variable | 812743pps -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 xconnect in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc03-9000B-1t1c-eth-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte -| | ... | frames using single trial throughput test at 2x 138580pps. -| | [Tags] | 9000B | 1T1C | STHREAD -| | ${framesize}= | Set Variable | ${9000} -| | ${rate}= | Set Variable | 138580pps -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 xconnect in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc04-64B-2t2c-eth-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 64 Byte -| | ... | frames using single trial throughput test at 2x 10.4mpps. -| | [Tags] | 64B | 2T2C | MTHREAD -| | ${framesize}= | Set Variable | ${64} -| | ${rate}= | Set Variable | 10.4mpps -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 xconnect in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc05-1518B-2t2c-eth-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 1518 Byte -| | ... | frames using single trial throughput test at 2x 812743pps. -| | [Tags] | 1518B | 2T2C | MTHREAD -| | ${framesize}= | Set Variable | ${1518} -| | ${rate}= | Set Variable | 812743pps -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 xconnect in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc06-9000B-2t2c-eth-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores, \ -| | ... | 1 receive queue per NIC port. [Ver] Verify ref-NDR for 9000 Byte -| | ... | frames using single trial throughput test at 2x 138580pps. -| | [Tags] | 9000B | 2T2C | MTHREAD -| | ${framesize}= | Set Variable | ${9000} -| | ${rate}= | Set Variable | 138580pps -| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 xconnect in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc07-64B-4t4c-eth-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 64 Byte -| | ... | frames using single trial throughput test at 2x 10.4mpps. -| | [Tags] | 64B | 4T4C | MTHREAD -| | ${framesize}= | Set Variable | ${64} -| | ${rate}= | Set Variable | 10.4mpps -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 xconnect in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc08-1518B-4t4c-eth-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 1518 Byte -| | ... | frames using single trial throughput test at 2x 812743pps. -| | [Tags] | 1518B | 4T4C | MTHREAD -| | ${framesize}= | Set Variable | ${1518} -| | ${rate}= | Set Variable | 812743pps -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 xconnect in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} - -| tc09-9000B-4t4c-eth-l2xcbase-ndrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores, \ -| | ... | 2 receive queues per NIC port. [Ver] Verify ref-NDR for 9000 Byte -| | ... | frames using single trial throughput test at 2x 138580pps. -| | [Tags] | 9000B | 4T4C | MTHREAD -| | ${framesize}= | Set Variable | ${9000} -| | ${rate}= | Set Variable | 138580pps -| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 xconnect in 3-node circular topology -| | Then Traffic should pass with no loss | ${perf_trial_duration} | ${rate} -| | ... | ${framesize} | ${traffic_profile} diff --git a/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-pdrchk.robot b/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-pdrchk.robot deleted file mode 100644 index 85627f0ea7..0000000000 --- a/tests/vpp/perf/l2/10ge2p1x520-eth-l2xcbase-pdrchk.robot +++ /dev/null @@ -1,184 +0,0 @@ -# Copyright (c) 2017 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance/performance_setup.robot -| Library | resources.libraries.python.InterfaceUtil -| Library | resources.libraries.python.NodePath -| ... -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PDRCHK -| ... | NIC_Intel-X520-DA2 | ETH | L2XCFWD | BASE | L2XCBASE -| ... -| Suite Setup | Set up 3-node performance topology with DUT's NIC model -| ... | L2 | Intel-X520-DA2 -| Suite Teardown | Tear down 3-node performance topology -| ... -| Test Setup | Set up performance test -| Test Teardown | Tear down performance pdrchk test -| ... -| Documentation | *Reference PDR throughput L2XC verify test cases* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 cross connect. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- -| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. -| ... | *[Ver] TG verification:* In short performance tests, TG verifies -| ... | DUTs' throughput at ref-PDR (reference Non Drop Rate) with zero packet -| ... | loss tolerance. Ref-PDR value is periodically updated acording to -| ... | formula: ref-PDR = 0.9x PDR, where PDR is found in RFC2544 long -| ... | performance tests for the same DUT configuration. Test packets are -| ... | generated by TG on links to DUTs. TG traffic profile contains two L3 -| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with -| ... | all packets containing Ethernet header, IPv4 header with IP protocol=61 -| ... | and static payload. MAC addresses are matching MAC addresses of the -| ... | TG node interfaces. -| ... | *[Ref] Applicable standard specifications:* RFC2544. - -*** Variables *** -# Traffic profile: -| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254 - -*** Keywords *** -| Check PDR for L2 xconnect -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with ${wt} thread, ${wt} phy core,\ -| | ... | ${rxq} receive queue per NIC port. -| | ... | [Ver] Verify ref-PDR for ${framesize} Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Arguments] | ${framesize} | ${rate} | ${wt} | ${rxq} -| | ... -| | # Test Variables required for test and test teardown -| | Set Test Variable | ${framesize} -| | Set Test Variable | ${rate} -| | ${get_framesize}= | Get Frame Size | ${framesize} -| | ... -| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Run Keyword If | ${get_framesize} < ${1522} -| | ... | Add no multi seg to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | And Initialize L2 xconnect in 3-node circular topology -| | Then Traffic should pass with partial loss | ${perf_trial_duration} -| | ... | ${rate} | ${framesize} | ${traffic_profile} -| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} - -*** Test Cases *** -| tc01-64B-1t1c-eth-l2xcbase-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 64B | 1T1C | STHREAD -| | ... -| | [Template] | Check PDR for L2 xconnect -| | framesize=${64} | rate=5.5mpps | wt=1 | rxq=1 - -| tc02-1518B-1t1c-eth-l2xcbase-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 1518B | 1T1C | STHREAD -| | ... -| | [Template] | Check PDR for L2 xconnect -| | framesize=${1518} | rate=812743pps | wt=1 | rxq=1 - -| tc03-9000B-1t1c-eth-l2xcbase-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 9000B | 1T1C | STHREAD -| | ... -| | [Template] | Check PDR for L2 xconnect -| | framesize=${9000} | rate=138580pps | wt=1 | rxq=1 - -| tc04-64B-2t2c-eth-l2xcbase-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 64B | 2T2C | MTHREAD -| | ... -| | [Template] | Check PDR for L2 xconnect -| | framesize=${64} | rate=10.4mpps | wt=2 | rxq=1 - -| tc05-1518B-2t2c-eth-l2xcbase-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 1518B | 2T2C | MTHREAD -| | ... -| | [Template] | Check PDR for L2 xconnect -| | framesize=${1518} | rate=812743pps | wt=2 | rxq=1 - -| tc06-9000B-2t2c-eth-l2xcbase-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 2 threads, 2 phy cores,\ -| | ... | 1 receive queue per NIC port. -| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 9000B | 2T2C | MTHREAD -| | ... -| | [Template] | Check PDR for L2 xconnect -| | framesize=${9000} | rate=100000pps | wt=2 | rxq=1 - -| tc07-64B-4t4c-eth-l2xcbase-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores,\ -| | ... | 2 receive queues per NIC port. -| | ... | [Ver] Verify ref-NDR for 64 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 64B | 4T4C | MTHREAD -| | ... -| | [Template] | Check PDR for L2 xconnect -| | framesize=${64} | rate=10.4mpps | wt=4 | rxq=2 - -| tc08-1518B-4t4c-eth-l2xcbase-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores,\ -| | ... | 2 receive queues per NIC port. -| | ... | [Ver] Verify ref-NDR for 1518 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 1518B | 4T4C | MTHREAD -| | ... -| | [Template] | Check PDR for L2 xconnect -| | framesize=${1518} | rate=812743pps | wt=4 | rxq=2 - -| tc09-9000B-4t4c-eth-l2xcbase-pdrchk -| | [Documentation] -| | ... | [Cfg] DUT runs L2XC config with 4 threads, 4 phy cores,\ -| | ... | 2 receive queues per NIC port. -| | ... | [Ver] Verify ref-NDR for 9000 Byte frames using single trial\ -| | ... | throughput test at 2x ${rate}. -| | ... -| | [Tags] | 9000B | 4T4C | MTHREAD -| | ... -| | [Template] | Check PDR for L2 xconnect -| | framesize=${9000} | rate=138580pps | wt=4 | rxq=2 |