diff options
Diffstat (limited to 'tests/vpp/perf')
20 files changed, 2228 insertions, 60 deletions
diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr.robot new file mode 100644 index 0000000000..4c517df0c6 --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr.robot @@ -0,0 +1,132 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | L2BDMACLRN | SCALE | L2BD_100 | DOT1Q | VLAN_100 +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_100 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2BD with IEEE 802.1Q and VXLANoIPv4 test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 100 L2\ +| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header,\ +| ... | IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan100ip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${100} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr.robot new file mode 100644 index 0000000000..fd057591b5 --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr.robot @@ -0,0 +1,139 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X520-DA2 | L2BDMACLRN | SCALE | L2BD_100 | DOT1Q | VLAN_100 +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_100 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 +| ... | test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 100 L2\ +| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header, IEEE\ +| ... | 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan100ip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${100} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr.robot new file mode 100644 index 0000000000..862bba7623 --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr.robot @@ -0,0 +1,132 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | L2BDMACLRN | SCALE | L2BD_10 | DOT1Q | VLAN_10 +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_10 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2BD with IEEE 802.1Q and VXLANoIPv4 test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 10 L2\ +| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header,\ +| ... | IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan10ip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${10} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr.robot new file mode 100644 index 0000000000..c567c5e422 --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr.robot @@ -0,0 +1,139 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X520-DA2 | L2BDMACLRN | SCALE | L2BD_10 | DOT1Q | VLAN_10 +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_10 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 +| ... | test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 10 L2\ +| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header, IEEE\ +| ... | 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan10ip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${10} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr.robot new file mode 100644 index 0000000000..b7f1c4dd7d --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr.robot @@ -0,0 +1,132 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | L2BDMACLRN | SCALE | L2BD_1K | DOT1Q | VLAN_1K +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_1K +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2BD with IEEE 802.1Q and VXLANoIPv4 test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 1k L2\ +| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header,\ +| ... | IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan1kip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${1000} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr.robot new file mode 100644 index 0000000000..86a177f672 --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr.robot @@ -0,0 +1,139 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X520-DA2 | L2BDMACLRN | SCALE | L2BD_1K | DOT1Q | VLAN_1K +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_1K +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 +| ... | test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 1k L2\ +| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header, IEEE\ +| ... | 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan1kip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${1000} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr.robot new file mode 100644 index 0000000000..6b45e3f033 --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr.robot @@ -0,0 +1,132 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | L2BDMACLRN | SCALE | L2BD_1 | DOT1Q | VLAN_1 +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_1 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2BD with IEEE 802.1Q and VXLANoIPv4 test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 1 L2\ +| ... | bridge domain. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header,\ +| ... | IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan1ip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${1} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr.robot new file mode 100644 index 0000000000..d02121c7b8 --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr.robot @@ -0,0 +1,139 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X520-DA2 | L2BDMACLRN | SCALE | L2BD_1 | DOT1Q | VLAN_1 +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_1 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 +| ... | test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 1 L2\ +| ... | bridge domain. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header, IEEE\ +| ... | 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan1ip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${1} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-mrr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-mrr.robot index 9ff706999f..b7b2144418 100644 --- a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-mrr.robot +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-mrr.robot @@ -29,19 +29,19 @@ | ... | Documentation | *Raw results L2BD with VXLANoIPv4 test cases* | ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ | ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain on TG-DUTn. -| ... | Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge -| ... | domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4 on\ +| ... | TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge\ +| ... | domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2.\ | ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. -| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic -| ... | at line rate and reports total received/sent packets over trial period. -| ... | Test packets are generated by TG on links to DUTs. TG traffic profile -| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per -| ... | flow-group) with all packets containing Ethernet header, IPv4 header -| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\ +| ... | flow-group) with all packets containing Ethernet header, IPv4 header\ +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\ | ... | addresses of the TG node interfaces. | ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. @@ -56,8 +56,8 @@ | Local Template | | ... | | [Documentation] -| | ... | [Cfg] DUT runs L2BD forwarding config. -| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VXLAN and uses\ +| | ... | ${phy_cores} physical core(s) for worker threads. | | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ | | ... | trial throughput test. | | ... diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-ndrpdr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-ndrpdr.robot index 1d2eb5ace3..595394a6d8 100644 --- a/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-ndrpdr.robot +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-ndrpdr.robot @@ -30,22 +30,22 @@ | ... | Documentation | *RFC2544: Pkt throughput L2BD with VXLANoIPv4 test cases* | ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ | ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain on TG-DUTn. -| ... | Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge -| ... | domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4 on\ +| ... | TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge\ +| ... | domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2.\ | ... | DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. -| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop -| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop -| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage -| ... | of packets transmitted. NDR and PDR are discovered for different -| ... | Ethernet L2 frame sizes using MLRsearch library. -| ... | Test packets are generated by TG on links to DUTs. TG traffic profile -| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per -| ... | flow-group) with all packets containing Ethernet header, IPv4 header -| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\ +| ... | flow-group) with all packets containing Ethernet header, IPv4 header\ +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\ | ... | addresses of the TG node interfaces. | ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. @@ -60,9 +60,9 @@ | Local Template | | ... | | [Documentation] -| | ... | [Cfg] DUT runs L2BD forwarding config. -| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. -| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\ +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VXLAN and uses\ +| | ... | ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. | | ... | | ... | *Arguments:* | | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr.robot new file mode 100644 index 0000000000..ff62345db6 --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr.robot @@ -0,0 +1,132 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X710 | L2BDMACLRN | SCALE | L2BD_100 | DOT1Q | VLAN_100 +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_100 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2BD with IEEE 802.1Q and VXLANoIPv4 test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 100 L2\ +| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header,\ +| ... | IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X710 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan100ip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${100} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr.robot new file mode 100644 index 0000000000..6e2755237d --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr.robot @@ -0,0 +1,139 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X710 | L2BDMACLRN | SCALE | L2BD_100 | DOT1Q | VLAN_100 +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_100 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 +| ... | test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 100 L2\ +| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header, IEEE\ +| ... | 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X710 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan100ip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${100} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr.robot new file mode 100644 index 0000000000..01b4059acf --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr.robot @@ -0,0 +1,132 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X710 | L2BDMACLRN | SCALE | L2BD_10 | DOT1Q | VLAN_10 +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_10 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2BD with IEEE 802.1Q and VXLANoIPv4 test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 10 L2\ +| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header,\ +| ... | IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X710 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan10ip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${10} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr.robot new file mode 100644 index 0000000000..bfc4f8d90b --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr.robot @@ -0,0 +1,139 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X710 | L2BDMACLRN | SCALE | L2BD_10 | DOT1Q | VLAN_10 +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_10 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 +| ... | test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 10 L2\ +| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header, IEEE\ +| ... | 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X710 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan10ip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${10} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr.robot new file mode 100644 index 0000000000..ce4be1c707 --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr.robot @@ -0,0 +1,132 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X710 | L2BDMACLRN | SCALE | L2BD_1K | DOT1Q | VLAN_1K +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_1K +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2BD with IEEE 802.1Q and VXLANoIPv4 test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 1k L2\ +| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header,\ +| ... | IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X710 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan1kip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${1000} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr.robot new file mode 100644 index 0000000000..66d34be226 --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr.robot @@ -0,0 +1,139 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X710 | L2BDMACLRN | SCALE | L2BD_1K | DOT1Q | VLAN_1K +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_1K +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 +| ... | test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 1k L2\ +| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header, IEEE\ +| ... | 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X710 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan1kip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${1000} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr.robot new file mode 100644 index 0000000000..74398e438f --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr.robot @@ -0,0 +1,132 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X710 | L2BDMACLRN | SCALE | L2BD_1 | DOT1Q | VLAN_1 +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_1 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2BD with IEEE 802.1Q and VXLANoIPv4 test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 1 L2\ +| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header,\ +| ... | IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X710 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan1ip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${1} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr.robot new file mode 100644 index 0000000000..c3b4fef1d1 --- /dev/null +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr.robot @@ -0,0 +1,139 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X710 | L2BDMACLRN | SCALE | L2BD_1 | DOT1Q | VLAN_1 +| ... | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY | VXLAN_1 +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L2 | Intel-X710 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 +| ... | test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-Dot1Q-IPv4 for L2 switching of IPv4\ +| ... | on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with 1 L2\ +| ... | bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and\ +| ... | DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, up to 64,5k\ +| ... | flows per flow-group) with all packets containing Ethernet header, IEEE\ +| ... | 802.1Q header, IPv4 header with IP protocol=61 and static payload.\ +| ... | MAC addresses are matching MAC addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. + +*** Variables *** +# X710 bandwidth limit +| ${s_limit}= | ${10000000000} +| ${overhead}= | ${50} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-dot1qip4-vlan1ip4src254ip4dst254 +# Number of VXLAN tunnels +| ${vxlan_count}= | ${1} + +*** Keywords *** +| Local Template +| | ... +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VLAN and VXLAN and\ +| | ... | uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 bridge domain with VLAN and VXLANoIPv4 in 3-node circular topology +| | ... | vxlan_count=${vxlan_count} +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q--ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-mrr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-mrr.robot index db41ca5b6b..829cc46693 100644 --- a/tests/vpp/perf/ip4_tunnels/10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-mrr.robot +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-mrr.robot @@ -29,19 +29,19 @@ | ... | Documentation | *Raw results L2BD with VXLANoIPv4 test cases* | ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ | ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain on TG-DUTn. -| ... | Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge -| ... | domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4 on\ +| ... | TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge\ +| ... | domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2.\ | ... | DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. -| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic -| ... | at line rate and reports total received/sent packets over trial period. -| ... | Test packets are generated by TG on links to DUTs. TG traffic profile -| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per -| ... | flow-group) with all packets containing Ethernet header, IPv4 header -| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\ +| ... | flow-group) with all packets containing Ethernet header, IPv4 header\ +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\ | ... | addresses of the TG node interfaces. | ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. @@ -55,8 +55,8 @@ *** Keywords *** | Local Template | | [Documentation] -| | ... | [Cfg] DUT runs L2BD forwarding config. -| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VXLAN and uses\ +| | ... | ${phy_cores} physical core(s) for worker threads. | | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ | | ... | trial throughput test. | | ... diff --git a/tests/vpp/perf/ip4_tunnels/10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-ndrpdr.robot b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-ndrpdr.robot index a68b5c4ec4..6f87803461 100644 --- a/tests/vpp/perf/ip4_tunnels/10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-ndrpdr.robot +++ b/tests/vpp/perf/ip4_tunnels/10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-ndrpdr.robot @@ -30,22 +30,22 @@ | ... | Documentation | *RFC2544: Pkt throughput L2BD with VXLANoIPv4 test cases* | ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ | ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain on TG-DUTn. -| ... | Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge -| ... | domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4 on\ +| ... | TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge\ +| ... | domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2.\ | ... | DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. -| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop -| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop -| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage -| ... | of packets transmitted. NDR and PDR are discovered for different -| ... | Ethernet L2 frame sizes using MLRsearch library. -| ... | Test packets are generated by TG on links to DUTs. TG traffic profile -| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per -| ... | flow-group) with all packets containing Ethernet header, IPv4 header -| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\ +| ... | flow-group) with all packets containing Ethernet header, IPv4 header\ +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\ | ... | addresses of the TG node interfaces. | ... | *[Ref] Applicable standard specifications:* RFC2544, RFC7348. @@ -59,9 +59,9 @@ *** Keywords *** | Local Template | | [Documentation] -| | ... | [Cfg] DUT runs L2BD forwarding config. -| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. -| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\ +| | ... | [Cfg] Each DUT runs L2BD forwarding config with VXLAN and uses\ +| | ... | ${phy_cores} physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. | | ... | | ... | *Arguments:* | | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). |