diff options
Diffstat (limited to 'tests/vpp/perf')
8 files changed, 1614 insertions, 667 deletions
diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4base-nat44-ndrpdrdisc.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4base-nat44-ndrpdrdisc.robot deleted file mode 100644 index 325b01ff6f..0000000000 --- a/tests/vpp/perf/ip4/10ge2p1x520-ethip4-ip4base-nat44-ndrpdrdisc.robot +++ /dev/null @@ -1,227 +0,0 @@ -# Copyright (c) 2017 Cisco and/or its affiliates. -# Licensed under the Apache License, Version 2.0 (the "License"); -# you may not use this file except in compliance with the License. -# You may obtain a copy of the License at: -# -# http://www.apache.org/licenses/LICENSE-2.0 -# -# Unless required by applicable law or agreed to in writing, software -# distributed under the License is distributed on an "AS IS" BASIS, -# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -# See the License for the specific language governing permissions and -# limitations under the License. - -*** Settings *** -| Resource | resources/libraries/robot/performance/performance_setup.robot -| Resource | resources/libraries/robot/ip/nat.robot -| Resource | resources/libraries/robot/shared/traffic.robot -| ... -| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC -| ... | NIC_Intel-X520-DA2 | ETH | IP4FWD | FEATURE | NAT44 | BASE -| ... -| Suite Setup | Set up 3-node performance topology with DUT's NIC model -| ... | L3 | Intel-X520-DA2 -| Suite Teardown | Tear down 3-node performance topology -| ... -| Test Setup | Set up performance test -| ... -| Test Teardown | Tear down performance discovery test with NAT -| ... | ${min_rate}pps | ${framesize} | ${traffic_profile} -| ... -| Documentation | *NAT44 performance test cases* -| ... -| ... | *High level description* -| ... -| ... | - NDR and PDR tests -| ... | - 3-node topology, TG-DUT1-DUT2-TG, NAT44 is enabled between DUTs. -| ... | - Cores / threads: 1t1c and 2t2c -| ... | - Framesize: 64B, 1518B, IMIX -| ... | - Packet: ETH / IP(src, dst) / UDP(src_port, dst_port) / payload -| ... -| ... | *Low level description* -| ... -| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology -| ... | with single links between nodes. -| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing. -| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4 -| ... | routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2 -| ... | tested with 2p10GE NIC X520 Niantic by Intel. -| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop -| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop -| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage -| ... | of packets transmitted. NDR and PDR are discovered for different -| ... | Ethernet L2 frame sizes using either binary search or linear search -| ... | algorithms with configured starting rate and final step that determines -| ... | throughput measurement resolution. Test packets are generated by TG on -| ... | links to DUTs. TG traffic profile contains two L3 flow-groups -| ... | (flow-group per direction, one flow per flow-group) with all packets -| ... | containing Ethernet header, IPv4 header with UDP header and static -| ... | payload. MAC addresses are matching MAC addresses of the TG node -| ... | interfaces. -| ... | *[Ref] Applicable standard specifications:* RFC2544. - -*** Variables *** -# X520-DA2 bandwidth limit -| ${s_limit} | ${10000000000} -# Traffic profile: -| ${traffic_profile} | trex-sl-3n-ethip4udp-1u1p - -*** Test Cases *** -| tc01-64B-1t1c-ethip4-ip4base-snat-1u-1p-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ -| | ... | 1 user and 1 port (session) per user. -| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ -| | ... | linerate, step 100kpps. -| | ... -| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC -| | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc02-64B-1t1c-ethip4-ip4base-snat-1u-1p-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ -| | ... | 1 user and 1 port (session) per user. -| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ -| | ... | linerate, step 100kpps. -| | ... -| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} - -| tc03-1518B-1t1c-ethip4-ip4base-snat-1u-1p-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ -| | ... | 1 user and 1 port (session) per user. -| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ -| | ... | linerate, step 100kpps. -| | ... -| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC -| | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc04-1518B-1t1c-ethip4-ip4base-snat-1u-1p-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ -| | ... | 1 user and 1 port (session) per user. -| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ -| | ... | linerate, step 100kpps. -| | ... -| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} - -| tc05-IMIX-1t1c-ethip4-ip4base-snat-1u-1p-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ -| | ... | 1 user and 1 port (session) per user. -| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ -| | ... | linerate, step 100kpps. -| | ... -| | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC -| | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} - -| tc06-IMIX-1t1c-ethip4-ip4base-snat-1u-1p-pdrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ -| | ... | 1 user and 1 port (session) per user. -| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ -| | ... | linerate, step 100kpps. -| | ... -| | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH -| | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4base-nat44-ndrpdrdisc.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4base-nat44-ndrpdrdisc.robot new file mode 100644 index 0000000000..2b12ca3a4d --- /dev/null +++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4base-nat44-ndrpdrdisc.robot @@ -0,0 +1,332 @@ +# Copyright (c) 2017 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| Resource | resources/libraries/robot/ip/nat.robot +| Resource | resources/libraries/robot/shared/traffic.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Intel-X520-DA2 | ETH | IP4FWD | FEATURE | NAT44 | BASE +| ... +| Suite Setup | Set up 3-node performance topology with DUT's NIC model +| ... | L3 | Intel-X520-DA2 +| Suite Teardown | Tear down 3-node performance topology +| ... +| Test Setup | Set up performance test +| ... +| Test Teardown | Tear down performance discovery test with NAT +| ... | ${min_rate}pps | ${framesize} | ${traffic_profile} +| ... +| Documentation | *NAT44 performance test cases* +| ... +| ... | *High level description* +| ... +| ... | - NDR and PDR tests +| ... | - 3-node topology, TG-DUT1-DUT2-TG, NAT44 is enabled between DUTs. +| ... | - Cores / threads: 1t1c, 2t2c, and 4t4c +| ... | - Framesize: 64B, 1518B, IMIX +| ... | - Packet: ETH / IP(src, dst) / UDP(src_port, dst_port) / payload +| ... +| ... | *Low level description* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4 +| ... | routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2 +| ... | tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, one flow per flow-group) with all packets +| ... | containing Ethernet header, IPv4 header with UDP header and static +| ... | payload. MAC addresses are matching MAC addresses of the TG node +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# X520-DA2 bandwidth limit +| ${s_limit} | ${10000000000} +# Traffic profile: +| ${traffic_profile} | trex-sl-3n-ethip4udp-1u1p + +*** Keywords *** +| Discover NDR or PDR for IPv4 routing with NAT44 +| | ... +| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology +| | And Add PCI devices to DUTs in 3-node single link topology +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs +| | And Add NAT to all DUTs +| | And Apply startup configuration on all VPP DUTs +| | When Initialize NAT44 in 3-node circular topology +| | Then Run Keyword If | '${search_type}' == 'NDR' +| | ... | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ELSE IF | '${search_type}' == 'PDR' +| | ... | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4-ip4base-snat-1u-1p-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc02-64B-1t1c-ethip4-ip4base-snat-1u-1p-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc03-1518B-1t1c-ethip4-ip4base-snat-1u-1p-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc04-1518B-1t1c-ethip4-ip4base-snat-1u-1p-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc05-IMIX-1t1c-ethip4-ip4base-snat-1u-1p-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc06-IMIX-1t1c-ethip4-ip4base-snat-1u-1p-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc07-64B-2t2c-ethip4-ip4base-snat-1u-1p-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc08-64B-2t2c-ethip4-ip4base-snat-1u-1p-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc09-1518B-2t2c-ethip4-ip4base-snat-1u-1p-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc10-1518B-2t2c-ethip4-ip4base-snat-1u-1p-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc11-IMIX-2t2c-ethip4-ip4base-snat-1u-1p-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc12-IMIX-2t2c-ethip4-ip4base-snat-1u-1p-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc13-64B-4t4c-ethip4-ip4base-snat-1u-1p-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc14-64B-4t4c-ethip4-ip4base-snat-1u-1p-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc15-1518B-4t4c-ethip4-ip4base-snat-1u-1p-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc16-1518B-4t4c-ethip4-ip4base-snat-1u-1p-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc17-IMIX-4t4c-ethip4-ip4base-snat-1u-1p-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc18-IMIX-4t4c-ethip4-ip4base-snat-1u-1p-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 1 port (session) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4base-udpsrcscale15-nat44-ndrpdrdisc.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4base-udpsrcscale15-nat44-ndrpdrdisc.robot index 62bea89f49..07fe756842 100644 --- a/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4base-udpsrcscale15-nat44-ndrpdrdisc.robot +++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4base-udpsrcscale15-nat44-ndrpdrdisc.robot @@ -34,7 +34,7 @@ | ... | ... | - NDR and PDR tests | ... | - 3-node topology, TG-DUT1-DUT2-TG, NAT44 is enabled between DUTs. -| ... | - Cores / threads: 1t1c and 2t2c +| ... | - Cores / threads: 1t1c, 2t2c, and 4t4c | ... | - Framesize: 64B, 1518B, IMIX | ... | - Packet: ETH / IP(src, dst) / UDP(src_port, dst_port) / payload | ... | - scale: src: 1 user, 10 users, 100 users, ..., 4000 up to the memory @@ -68,32 +68,49 @@ # Traffic profile: | ${traffic_profile} | trex-sl-3n-ethip4udp-1u15p -*** Test Cases *** -| tc01-64B-1t1c-ethip4udp-ip4base-udpsrcscale15-snat-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ -| | ... | 1 user and 15 ports (sessions) per user. -| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ -| | ... | linerate, step 100kpps. +*** Keywords *** +| Discover NDR or PDR for IPv4 routing with NAT44 | | ... -| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type} | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology | | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs | | And Add NAT to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} +| | Then Run Keyword If | '${search_type}' == 'NDR' +| | ... | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} | | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ELSE IF | '${search_type}' == 'PDR' +| | ... | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4udp-ip4base-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR | tc02-64B-1t1c-ethip4udp-ip4base-udpsrcscale15-snat-pdrdisc | | [Documentation] @@ -105,22 +122,8 @@ | | ... | | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR | tc03-1518B-1t1c-ethip4udp-ip4base-udpsrcscale15-snat-ndrdisc | | [Documentation] @@ -132,21 +135,8 @@ | | ... | | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC | | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR | tc04-1518B-1t1c-ethip4udp-ip4base-udpsrcscale15-snat-pdrdisc | | [Documentation] @@ -158,22 +148,8 @@ | | ... | | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR | tc05-IMIX-1t1c-ethip4udp-ip4base-udpsrcscale15-snat-ndrdisc | | [Documentation] @@ -185,21 +161,8 @@ | | ... | | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC | | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR | tc06-IMIX-1t1c-ethip4udp-ip4base-udpsrcscale15-snat-pdrdisc | | [Documentation] @@ -211,19 +174,161 @@ | | ... | | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc07-64B-2t2c-ethip4udp-ip4base-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc08-64B-2t2c-ethip4udp-ip4base-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc09-1518B-2t2c-ethip4udp-ip4base-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc10-1518B-2t2c-ethip4udp-ip4base-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc11-IMIX-2t2c-ethip4udp-ip4base-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc12-IMIX-2t2c-ethip4udp-ip4base-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc13-64B-4t4c-ethip4udp-ip4base-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc14-64B-4t4c-ethip4udp-ip4base-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc15-1518B-4t4c-ethip4udp-ip4base-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc16-1518B-4t4c-ethip4udp-ip4base-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc17-IMIX-4t4c-ethip4udp-ip4base-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc18-IMIX-4t4c-ethip4udp-ip4base-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1 user and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale10-udpsrcscale15-nat44-ndrpdrdisc.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale10-udpsrcscale15-nat44-ndrpdrdisc.robot index ade9d42eeb..ff299de17a 100644 --- a/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale10-udpsrcscale15-nat44-ndrpdrdisc.robot +++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale10-udpsrcscale15-nat44-ndrpdrdisc.robot @@ -35,7 +35,7 @@ | ... | ... | - NDR and PDR tests | ... | - 3-node topology, TG-DUT1-DUT2-TG, NAT44 is enabled between DUTs. -| ... | - Cores / threads: 1t1c and 2t2c +| ... | - Cores / threads: 1t1c, 2t2c, and 4t4c | ... | - Framesize: 64B, 1518B, IMIX | ... | - Packet: ETH / IP(src, dst) / UDP(src_port, dst_port) / payload | ... | - scale: src: 1 user, 10 users, 100 users, ..., 4000 up to the memory @@ -69,32 +69,49 @@ # Traffic profile: | ${traffic_profile} | trex-sl-3n-ethip4udp-10u15p -*** Test Cases *** -| tc01-64B-1t1c-ethip4udp-ip4scale10-udpsrcscale15-snat-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ -| | ... | 10 users and 15 ports (sessions) per user. -| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ -| | ... | linerate, step 100kpps. +*** Keywords *** +| Discover NDR or PDR for IPv4 routing with NAT44 | | ... -| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type} | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology | | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs | | And Add NAT to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} +| | Then Run Keyword If | '${search_type}' == 'NDR' +| | ... | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} | | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ELSE IF | '${search_type}' == 'PDR' +| | ... | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4udp-ip4scale10-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 10 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR | tc02-64B-1t1c-ethip4udp-ip4scale10-udpsrcscale15-snat-pdrdisc | | [Documentation] @@ -106,22 +123,8 @@ | | ... | | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR | tc03-1518B-1t1c-ethip4udp-ip4scale10-udpsrcscale15-snat-ndrdisc | | [Documentation] @@ -133,21 +136,8 @@ | | ... | | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC | | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR | tc04-1518B-1t1c-ethip4udp-ip4scale10-udpsrcscale15-snat-pdrdisc | | [Documentation] @@ -159,22 +149,8 @@ | | ... | | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR | tc05-IMIX-1t1c-ethip4udp-ip4scale10-udpsrcscale15-snat-ndrdisc | | [Documentation] @@ -186,21 +162,8 @@ | | ... | | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC | | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR | tc06-IMIX-1t1c-ethip4udp-ip4scale10-udpsrcscale15-snat-pdrdisc | | [Documentation] @@ -212,19 +175,161 @@ | | ... | | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc07-64B-2t2c-ethip4udp-ip4scale10-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 10 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc08-64B-2t2c-ethip4udp-ip4scale10-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 10 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc09-1518B-2t2c-ethip4udp-ip4scale10-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 10 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc10-1518B-2t2c-ethip4udp-ip4scale10-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 10 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc11-IMIX-2t2c-ethip4udp-ip4scale10-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 10 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc12-IMIX-2t2c-ethip4udp-ip4scale10-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 10 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc13-64B-4t4c-ethip4udp-ip4scale10-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 10 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc14-64B-4t4c-ethip4udp-ip4scale10-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 10 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc15-1518B-4t4c-ethip4udp-ip4scale10-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 10 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc16-1518B-4t4c-ethip4udp-ip4scale10-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 10 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc17-IMIX-4t4c-ethip4udp-ip4scale10-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 10 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc18-IMIX-4t4c-ethip4udp-ip4scale10-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 10 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale100-udpsrcscale15-nat44-ndrpdrdisc.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale100-udpsrcscale15-nat44-ndrpdrdisc.robot index 57d9bf6543..3997c9187e 100644 --- a/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale100-udpsrcscale15-nat44-ndrpdrdisc.robot +++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale100-udpsrcscale15-nat44-ndrpdrdisc.robot @@ -35,7 +35,7 @@ | ... | ... | - NDR and PDR tests | ... | - 3-node topology, TG-DUT1-DUT2-TG, NAT44 is enabled between DUTs. -| ... | - Cores / threads: 1t1c and 2t2c +| ... | - Cores / threads: 1t1c, 2t2c, and 4t4c | ... | - Framesize: 64B, 1518B, IMIX | ... | - Packet: ETH / IP(src, dst) / UDP(src_port, dst_port) / payload | ... | - scale: src: 1 user, 10 users, 100 users, ..., 4000 up to the memory @@ -69,32 +69,49 @@ # Traffic profile: | ${traffic_profile} | trex-sl-3n-ethip4udp-100u15p -*** Test Cases *** -| tc01-64B-1t1c-ethip4udp-ip4scale100-udpsrcscale15-snat-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ -| | ... | 100 users and 15 ports (sessions) per user. -| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ -| | ... | linerate, step 100kpps. +*** Keywords *** +| Discover NDR or PDR for IPv4 routing with NAT44 | | ... -| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type} | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology | | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs | | And Add NAT to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} +| | Then Run Keyword If | '${search_type}' == 'NDR' +| | ... | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} | | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ELSE IF | '${search_type}' == 'PDR' +| | ... | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4udp-ip4scale100-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 100 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR | tc02-64B-1t1c-ethip4udp-ip4scale100-udpsrcscale15-snat-pdrdisc | | [Documentation] @@ -106,22 +123,8 @@ | | ... | | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR | tc03-1518B-1t1c-ethip4udp-ip4scale100-udpsrcscale15-snat-ndrdisc | | [Documentation] @@ -133,21 +136,8 @@ | | ... | | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC | | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR | tc04-1518B-1t1c-ethip4udp-ip4scale100-udpsrcscale15-snat-pdrdisc | | [Documentation] @@ -159,22 +149,8 @@ | | ... | | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR | tc05-IMIX-1t1c-ethip4udp-ip4scale100-udpsrcscale15-snat-ndrdisc | | [Documentation] @@ -186,21 +162,8 @@ | | ... | | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC | | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR | tc06-IMIX-1t1c-ethip4udp-ip4scale100-udpsrcscale15-snat-pdrdisc | | [Documentation] @@ -212,19 +175,161 @@ | | ... | | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc07-64B-2t2c-ethip4udp-ip4scale100-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 100 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc08-64B-2t2c-ethip4udp-ip4scale100-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 100 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc09-1518B-2t2c-ethip4udp-ip4scale100-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 100 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc10-1518B-2t2c-ethip4udp-ip4scale100-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 100 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc11-IMIX-2t2c-ethip4udp-ip4scale100-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 100 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc12-IMIX-2t2c-ethip4udp-ip4scale100-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 100 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc13-64B-4t4c-ethip4udp-ip4scale100-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 100 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc14-64B-4t4c-ethip4udp-ip4scale100-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 100 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc15-1518B-4t4c-ethip4udp-ip4scale100-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 100 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc16-1518B-4t4c-ethip4udp-ip4scale100-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 100 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc17-IMIX-4t4c-ethip4udp-ip4scale100-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 100 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc18-IMIX-4t4c-ethip4udp-ip4scale100-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 100 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdrdisc.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdrdisc.robot index bc0ef7e500..d3bbd575e3 100644 --- a/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdrdisc.robot +++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdrdisc.robot @@ -35,7 +35,7 @@ | ... | ... | - NDR and PDR tests | ... | - 3-node topology, TG-DUT1-DUT2-TG, NAT44 is enabled between DUTs. -| ... | - Cores / threads: 1t1c and 2t2c +| ... | - Cores / threads: 1t1c, 2t2c, and 4t4c | ... | - Framesize: 64B, 1518B, IMIX | ... | - Packet: ETH / IP(src, dst) / UDP(src_port, dst_port) / payload | ... | - scale: src: 1 user, 10 users, 100 users, ..., 4000 up to the memory @@ -69,32 +69,49 @@ # Traffic profile: | ${traffic_profile} | trex-sl-3n-ethip4udp-1000u15p -*** Test Cases *** -| tc01-64B-1t1c-ethip4udp-ip4scale1000-udpsrcscale15-snat-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ -| | ... | 1000 users and 15 ports (sessions) per user. -| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ -| | ... | linerate, step 100kpps. +*** Keywords *** +| Discover NDR or PDR for IPv4 routing with NAT44 | | ... -| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type} | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology | | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs | | And Add NAT to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} +| | Then Run Keyword If | '${search_type}' == 'NDR' +| | ... | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} | | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ELSE IF | '${search_type}' == 'PDR' +| | ... | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4udp-ip4scale1000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR | tc02-64B-1t1c-ethip4udp-ip4scale1000-udpsrcscale15-snat-pdrdisc | | [Documentation] @@ -106,22 +123,8 @@ | | ... | | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR | tc03-1518B-1t1c-ethip4udp-ip4scale1000-udpsrcscale15-snat-ndrdisc | | [Documentation] @@ -133,21 +136,8 @@ | | ... | | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC | | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR | tc04-1518B-1t1c-ethip4udp-ip4scale1000-udpsrcscale15-snat-pdrdisc | | [Documentation] @@ -159,22 +149,8 @@ | | ... | | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | ${1518} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR | tc05-IMIX-1t1c-ethip4udp-ip4scale1000-udpsrcscale15-snat-ndrdisc | | [Documentation] @@ -186,21 +162,8 @@ | | ... | | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC | | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR | tc06-IMIX-1t1c-ethip4udp-ip4scale1000-udpsrcscale15-snat-pdrdisc | | [Documentation] @@ -212,19 +175,161 @@ | | ... | | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | IMIX_v4_1 -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc07-64B-2t2c-ethip4udp-ip4scale1000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc08-64B-2t2c-ethip4udp-ip4scale1000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc09-1518B-2t2c-ethip4udp-ip4scale1000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc10-1518B-2t2c-ethip4udp-ip4scale1000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc11-IMIX-2t2c-ethip4udp-ip4scale1000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc12-IMIX-2t2c-ethip4udp-ip4scale1000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc13-64B-4t4c-ethip4udp-ip4scale1000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc14-64B-4t4c-ethip4udp-ip4scale1000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc15-1518B-4t4c-ethip4udp-ip4scale1000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc16-1518B-4t4c-ethip4udp-ip4scale1000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc17-IMIX-4t4c-ethip4udp-ip4scale1000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc18-IMIX-4t4c-ethip4udp-ip4scale1000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 1000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale2000-udpsrcscale15-nat44-ndrpdrdisc.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale2000-udpsrcscale15-nat44-ndrpdrdisc.robot index 056f213805..dcc74efacc 100644 --- a/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale2000-udpsrcscale15-nat44-ndrpdrdisc.robot +++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale2000-udpsrcscale15-nat44-ndrpdrdisc.robot @@ -35,7 +35,7 @@ | ... | ... | - NDR and PDR tests | ... | - 3-node topology, TG-DUT1-DUT2-TG, NAT44 is enabled between DUTs. -| ... | - Cores / threads: 1t1c and 2t2c +| ... | - Cores / threads: 1t1c, 2t2c, and 4t4c | ... | - Framesize: 64B, 1518B, IMIX | ... | - Packet: ETH / IP(src, dst) / UDP(src_port, dst_port) / payload | ... | - scale: src: 1 user, 10 users, 100 users, ..., 4000 up to the memory @@ -69,32 +69,49 @@ # Traffic profile: | ${traffic_profile} | trex-sl-3n-ethip4udp-2000u15p -*** Test Cases *** -| tc01-64B-1t1c-ethip4udp-ip4scale2000-udpsrcscale15-snat-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ -| | ... | 2000 users and 15 ports (sessions) per user. -| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ -| | ... | linerate, step 100kpps. +*** Keywords *** +| Discover NDR or PDR for IPv4 routing with NAT44 | | ... -| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type} | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology | | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs | | And Add NAT to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} +| | Then Run Keyword If | '${search_type}' == 'NDR' +| | ... | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} | | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ELSE IF | '${search_type}' == 'PDR' +| | ... | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4udp-ip4scale2000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR | tc02-64B-1t1c-ethip4udp-ip4scale2000-udpsrcscale15-snat-pdrdisc | | [Documentation] @@ -106,19 +123,213 @@ | | ... | | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc03-1518B-1t1c-ethip4udp-ip4scale2000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc04-1518B-1t1c-ethip4udp-ip4scale2000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc05-IMIX-1t1c-ethip4udp-ip4scale2000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc06-IMIX-1t1c-ethip4udp-ip4scale2000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc07-64B-2t2c-ethip4udp-ip4scale2000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc08-64B-2t2c-ethip4udp-ip4scale2000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc09-1518B-2t2c-ethip4udp-ip4scale2000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc10-1518B-2t2c-ethip4udp-ip4scale2000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc11-IMIX-2t2c-ethip4udp-ip4scale2000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc12-IMIX-2t2c-ethip4udp-ip4scale2000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc13-64B-4t4c-ethip4udp-ip4scale2000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc14-64B-4t4c-ethip4udp-ip4scale2000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc15-1518B-4t4c-ethip4udp-ip4scale2000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc16-1518B-4t4c-ethip4udp-ip4scale2000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc17-IMIX-4t4c-ethip4udp-ip4scale2000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc18-IMIX-4t4c-ethip4udp-ip4scale2000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 2000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR diff --git a/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale4000-udpsrcscale15-nat44-ndrpdrdisc.robot b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale4000-udpsrcscale15-nat44-ndrpdrdisc.robot index cd7bf41732..20d3fb4ea3 100644 --- a/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale4000-udpsrcscale15-nat44-ndrpdrdisc.robot +++ b/tests/vpp/perf/ip4/10ge2p1x520-ethip4udp-ip4scale4000-udpsrcscale15-nat44-ndrpdrdisc.robot @@ -35,7 +35,7 @@ | ... | ... | - NDR and PDR tests | ... | - 3-node topology, TG-DUT1-DUT2-TG, NAT44 is enabled between DUTs. -| ... | - Cores / threads: 1t1c and 2t2c +| ... | - Cores / threads: 1t1c, 2t2c, and 4t4c | ... | - Framesize: 64B, 1518B, IMIX | ... | - Packet: ETH / IP(src, dst) / UDP(src_port, dst_port) / payload | ... | - scale: src: 1 user, 10 users, 100 users, ..., 4000 up to the memory @@ -69,32 +69,49 @@ # Traffic profile: | ${traffic_profile} | trex-sl-3n-ethip4udp-4000u15p -*** Test Cases *** -| tc01-64B-1t1c-ethip4udp-ip4scale4000-udpsrcscale15-snat-ndrdisc -| | [Documentation] -| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ -| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ -| | ... | 4000 users and 15 ports (sessions) per user. -| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ -| | ... | linerate, step 100kpps. +*** Keywords *** +| Discover NDR or PDR for IPv4 routing with NAT44 | | ... -| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type} | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology +| | ${get_framesize}= | Get Frame Size | ${framesize} +| | ... +| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology | | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs +| | And Run Keyword If | ${get_framesize} < ${1522} +| | ... | Add no multi seg to all DUTs | | And Add NAT to all DUTs | | And Apply startup configuration on all VPP DUTs | | When Initialize NAT44 in 3-node circular topology -| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} +| | Then Run Keyword If | '${search_type}' == 'NDR' +| | ... | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} | | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ELSE IF | '${search_type}' == 'PDR' +| | ... | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile} +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-ethip4udp-ip4scale4000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR | tc02-64B-1t1c-ethip4udp-ip4scale4000-udpsrcscale15-snat-pdrdisc | | [Documentation] @@ -106,19 +123,213 @@ | | ... | | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH | | ... -| | ${framesize}= | Set Variable | ${64} -| | ${min_rate}= | Set Variable | ${100000} -| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} -| | ${binary_min}= | Set Variable | ${min_rate} -| | ${binary_max}= | Set Variable | ${max_rate} -| | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology -| | And Add PCI devices to DUTs in 3-node single link topology -| | And Add no multi seg to all DUTs -| | And Add NAT to all DUTs -| | And Apply startup configuration on all VPP DUTs -| | When Initialize NAT44 in 3-node circular topology -| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min} -| | ... | ${binary_max} | ${traffic_profile} -| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance} -| | ... | ${perf_pdr_loss_acceptance_type} +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc03-1518B-1t1c-ethip4udp-ip4scale4000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc04-1518B-1t1c-ethip4udp-ip4scale4000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc05-IMIX-1t1c-ethip4udp-ip4scale4000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc06-IMIX-1t1c-ethip4udp-ip4scale4000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=1 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc07-64B-2t2c-ethip4udp-ip4scale4000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc08-64B-2t2c-ethip4udp-ip4scale4000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc09-1518B-2t2c-ethip4udp-ip4scale4000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc10-1518B-2t2c-ethip4udp-ip4scale4000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc11-IMIX-2t2c-ethip4udp-ip4scale4000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc12-IMIX-2t2c-ethip4udp-ip4scale4000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores,\ +| | ... | 1 receive queue per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=2 | rxq=1 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR + +| tc13-64B-4t4c-ethip4udp-ip4scale4000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=NDR + +| tc14-64B-4t4c-ethip4udp-ip4scale4000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${64} | min_rate=${100000} | search_type=PDR + +| tc15-1518B-4t4c-ethip4udp-ip4scale4000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=NDR + +| tc16-1518B-4t4c-ethip4udp-ip4scale4000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=PDR + +| tc17-IMIX-4t4c-ethip4udp-ip4scale4000-udpsrcscale15-snat-ndrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | NDRDISC +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=NDR + +| tc18-IMIX-4t4c-ethip4udp-ip4scale4000-udpsrcscale15-snat-pdrdisc +| | [Documentation] +| | ... | [Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores,\ +| | ... | 2 receive queues per NIC port. NAT44 is configured between DUTs -\ +| | ... | 4000 users and 15 ports (sessions) per user. +| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | ... +| | [Tags] | IMIX | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | ... +| | [Template] | Discover NDR or PDR for IPv4 routing with NAT44 +| | wt=4 | rxq=2 | framesize=IMIX_v4_1 | min_rate=${100000} | search_type=PDR |