diff options
Diffstat (limited to 'tests/vpp/perf')
8 files changed, 1242 insertions, 0 deletions
diff --git a/tests/vpp/perf/container_memif/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr.robot b/tests/vpp/perf/container_memif/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr.robot new file mode 100644 index 0000000000..ea4f9f8758 --- /dev/null +++ b/tests/vpp/perf/container_memif/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr.robot @@ -0,0 +1,151 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X520-DA2 | DOT1Q | L2BDMACLRN | BASE | MEMIF | DOCKER +| ... +| Suite Setup | Run Keywords +| ... | Set up 3-node performance topology with DUT's NIC model | L2 +| ... | Intel-X520-DA2 +| ... | AND | Set up performance test suite with MEMIF +| ... | AND | Set up performance topology with containers +| ... +| Suite Teardown | Tear down 3-node performance topology with container +| ... +| Test Setup | Run Keywords +| ... | Set up performance test +| ... | AND | Restart VPP in all 'VNF' containers +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2BD with memif and IEEE 802.1Q test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain. IEEE\ +| ... | 802.1Q tagging is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with two L2\ +| ... | bridge domains and MAC learning enabled. Container is connected to VPP\ +| ... | via Memif interface. Container is running same VPP version as running\ +| ... | on DUT. Container is limited via cgroup to use 3 cores allocated from\ +| ... | pool of isolated CPUs. There are no memory constraints. DUT1 and DUT2\ +| ... | tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\ +| ... | flow-group) with all packets containing Ethernet header, IPv4 header\ +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\ +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${subid}= | 10 +| ${tag_rewrite}= | pop-1 +| ${bd_id1}= | 1 +| ${bd_id2}= | 2 +| ${overhead}= | ${4} +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src254 +# LXC container +| ${container_count}= | ${1} +| ${container_engine}= | Docker +| ${container_image}= | ubuntu:xenial-20180412 +| ${container_install_dkms}= | ${FALSE} +| ${container_chain_topology}= | chain +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${container_cpus}= | ${5} + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD switching with VLAN and uses ${phy_cores}\ +| | ... | physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 Bridge Domain with memif pairs and VLAN in circular topology +| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite} +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/container_memif/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr.robot b/tests/vpp/perf/container_memif/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr.robot new file mode 100644 index 0000000000..370500f264 --- /dev/null +++ b/tests/vpp/perf/container_memif/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr.robot @@ -0,0 +1,158 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X520-DA2 | DOT1Q | L2BDMACLRN | BASE | MEMIF | DOCKER +| ... +| Suite Setup | Run Keywords +| ... | Set up 3-node performance topology with DUT's NIC model | L2 +| ... | Intel-X520-DA2 +| ... | AND | Set up performance test suite with MEMIF +| ... | AND | Set up performance topology with containers +| ... +| Suite Teardown | Tear down 3-node performance topology with container +| ... +| Test Setup | Run Keywords +| ... | Set up performance test +| ... | AND | Restart VPP in all 'VNF' containers +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2BD with memif and IEEE 802.1Q test +| ... | cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain. IEEE\ +| ... | 802.1Q tagging is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with two L2\ +| ... | bridge domains and MAC learning enabled. Container is connected to VPP\ +| ... | via Memif interface. Container is running same VPP version as running\ +| ... | on DUT. Container is limited via cgroup to use 3 cores allocated from\ +| ... | pool of isolated CPUs. There are no memory constraints. DUT1 and DUT2\ +| ... | tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\ +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3\ +| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with\ +| ... | all packets containing Ethernet header, IPv4 header with IP\ +| ... | protocol=61 and static payload. MAC addresses are matching MAC\ +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${subid}= | 10 +| ${tag_rewrite}= | pop-1 +| ${bd_id1}= | 1 +| ${bd_id2}= | 2 +| ${overhead}= | ${4} +# X520-DA2 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src254 +# LXC container +| ${container_count}= | ${1} +| ${container_engine}= | Docker +| ${container_image}= | ubuntu:xenial-20180412 +| ${container_install_dkms}= | ${FALSE} +| ${container_chain_topology}= | chain +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${container_cpus}= | ${5} + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD switching with VLAN and uses ${phy_cores}\ +| | ... | physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 Bridge Domain with memif pairs and VLAN in circular topology +| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite} +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/container_memif/10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr.robot b/tests/vpp/perf/container_memif/10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr.robot new file mode 100644 index 0000000000..60e0542781 --- /dev/null +++ b/tests/vpp/perf/container_memif/10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr.robot @@ -0,0 +1,151 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X710 | DOT1Q | L2BDMACLRN | BASE | MEMIF | DOCKER +| ... +| Suite Setup | Run Keywords +| ... | Set up 3-node performance topology with DUT's NIC model | L2 +| ... | Intel-X710 +| ... | AND | Set up performance test suite with MEMIF +| ... | AND | Set up performance topology with containers +| ... +| Suite Teardown | Tear down 3-node performance topology with container +| ... +| Test Setup | Run Keywords +| ... | Set up performance test +| ... | AND | Restart VPP in all 'VNF' containers +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2BD with memif and IEEE 802.1Q test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain. IEEE\ +| ... | 802.1Q tagging is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with two L2\ +| ... | bridge domains and MAC learning enabled. Container is connected to VPP\ +| ... | via Memif interface. Container is running same VPP version as running\ +| ... | on DUT. Container is limited via cgroup to use 3 cores allocated from\ +| ... | pool of isolated CPUs. There are no memory constraints. DUT1 and DUT2\ +| ... | tested with 2p10GE NIC X710 by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period.\ +| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\ +| ... | flow-group) with all packets containing Ethernet header, IPv4 header\ +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\ +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${subid}= | 10 +| ${tag_rewrite}= | pop-1 +| ${bd_id1}= | 1 +| ${bd_id2}= | 2 +| ${overhead}= | ${4} +# X710 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src254 +# LXC container +| ${container_count}= | ${1} +| ${container_engine}= | Docker +| ${container_image}= | ubuntu:xenial-20180412 +| ${container_install_dkms}= | ${FALSE} +| ${container_chain_topology}= | chain +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${container_cpus}= | ${5} + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD switching with VLAN and uses ${phy_cores}\ +| | ... | physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 Bridge Domain with memif pairs and VLAN in circular topology +| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite} +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/container_memif/10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr.robot b/tests/vpp/perf/container_memif/10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr.robot new file mode 100644 index 0000000000..5e9db6c62f --- /dev/null +++ b/tests/vpp/perf/container_memif/10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr.robot @@ -0,0 +1,158 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X710 | DOT1Q | L2BDMACLRN | BASE | MEMIF | DOCKER +| ... +| Suite Setup | Run Keywords +| ... | Set up 3-node performance topology with DUT's NIC model | L2 +| ... | Intel-X710 +| ... | AND | Set up performance test suite with MEMIF +| ... | AND | Set up performance topology with containers +| ... +| Suite Teardown | Tear down 3-node performance topology with container +| ... +| Test Setup | Run Keywords +| ... | Set up performance test +| ... | AND | Restart VPP in all 'VNF' containers +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2BD with memif and IEEE 802.1Q test +| ... | cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain. IEEE\ +| ... | 802.1Q tagging is applied on link between DUT1 and DUT2. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with two L2\ +| ... | bridge domains and MAC learning enabled. Container is connected to VPP\ +| ... | via Memif interface. Container is running same VPP version as running\ +| ... | on DUT. Container is limited via cgroup to use 3 cores allocated from\ +| ... | pool of isolated CPUs. There are no memory constraints. DUT1 and DUT2\ +| ... | tested with 2p10GE NIC X710 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\ +| ... | generated by TG on links to DUTs. TG traffic profile contains two L3\ +| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with\ +| ... | all packets containing Ethernet header, IPv4 header with IP\ +| ... | protocol=61 and static payload. MAC addresses are matching MAC\ +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${subid}= | 10 +| ${tag_rewrite}= | pop-1 +| ${bd_id1}= | 1 +| ${bd_id2}= | 2 +| ${overhead}= | ${4} +# X710 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile}= | trex-sl-3n-ethip4-ip4src254 +# LXC container +| ${container_count}= | ${1} +| ${container_engine}= | Docker +| ${container_image}= | ubuntu:xenial-20180412 +| ${container_install_dkms}= | ${FALSE} +| ${container_chain_topology}= | chain +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${container_cpus}= | ${5} + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD switching with VLAN and uses ${phy_cores}\ +| | ... | physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 Bridge Domain with memif pairs and VLAN in circular topology +| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite} +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/container_memif/2n1l-10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr.robot b/tests/vpp/perf/container_memif/2n1l-10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr.robot new file mode 100644 index 0000000000..f250e801b0 --- /dev/null +++ b/tests/vpp/perf/container_memif/2n1l-10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr.robot @@ -0,0 +1,151 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-X710 | DOT1Q | L2BDMACLRN | BASE | MEMIF | DOCKER +| ... +| Suite Setup | Run Keywords +| ... | Set up 2-node performance topology with DUT's NIC model | L2 +| ... | Intel-X710 +| ... | AND | Set up performance test suite with MEMIF +| ... | AND | Set up performance topology with containers +| ... +| Suite Teardown | Tear down 2-node performance topology with container +| ... +| Test Setup | Run Keywords +| ... | Set up performance test +| ... | AND | Restart VPP in all 'VNF' containers +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2BD with memif and IEEE 802.1Q test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\ +| ... | single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain. IEEE\ +| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with two L2 bridge\ +| ... | domains and MAC learning enabled. Container is connected to VPP via\ +| ... | Memif interface. Container is running same VPP version as running\ +| ... | on DUT. Container is limited via cgroup to use 3 cores allocated from\ +| ... | pool of isolated CPUs. There are no memory constraints. DUT1 is tested\ +| ... | with 2p10GE NIC X710 by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period.\ +| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\ +| ... | flow-group) with all packets containing Ethernet header, IPv4 header\ +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\ +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${subid}= | 10 +| ${tag_rewrite}= | pop-1 +| ${bd_id1}= | 1 +| ${bd_id2}= | 2 +| ${overhead}= | ${4} +# X710 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254 +# LXC container +| ${container_count}= | ${1} +| ${container_engine}= | Docker +| ${container_image}= | ubuntu:xenial-20180412 +| ${container_install_dkms}= | ${FALSE} +| ${container_chain_topology}= | chain +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${container_cpus}= | ${5} + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD switching with VLAN and uses ${phy_cores}\ +| | ... | physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 Bridge Domain with memif pairs and VLAN in circular topology +| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite} +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/container_memif/2n1l-10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr.robot b/tests/vpp/perf/container_memif/2n1l-10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr.robot new file mode 100644 index 0000000000..2ec53e4c56 --- /dev/null +++ b/tests/vpp/perf/container_memif/2n1l-10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr.robot @@ -0,0 +1,158 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-X710 | DOT1Q | L2BDMACLRN | BASE | MEMIF | DOCKER +| ... +| Suite Setup | Run Keywords +| ... | Set up 2-node performance topology with DUT's NIC model | L2 +| ... | Intel-X710 +| ... | AND | Set up performance test suite with MEMIF +| ... | AND | Set up performance topology with containers +| ... +| Suite Teardown | Tear down 2-node performance topology with container +| ... +| Test Setup | Run Keywords +| ... | Set up performance test +| ... | AND | Restart VPP in all 'VNF' containers +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2BD with memif and IEEE 802.1Q test +| ... | cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\ +| ... | single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain. IEEE\ +| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with two L2 bridge\ +| ... | domains and MAC learning enabled. Container is connected to VPP via\ +| ... | Memif interface. Container is running same VPP version as running\ +| ... | on DUT. Container is limited via cgroup to use 3 cores allocated from\ +| ... | pool of isolated CPUs. There are no memory constraints. DUT1 is tested\ +| ... | with 2p10GE NIC X710 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\ +| ... | generated by TG on links to DUT1. TG traffic profile contains two L3\ +| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with\ +| ... | all packets containing Ethernet header, IPv4 header with IP\ +| ... | protocol=61 and static payload. MAC addresses are matching MAC\ +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${subid}= | 10 +| ${tag_rewrite}= | pop-1 +| ${bd_id1}= | 1 +| ${bd_id2}= | 2 +| ${overhead}= | ${4} +# X710 bandwidth limit +| ${s_limit}= | ${10000000000} +# Traffic profile: +| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254 +# LXC container +| ${container_count}= | ${1} +| ${container_engine}= | Docker +| ${container_image}= | ubuntu:xenial-20180412 +| ${container_install_dkms}= | ${FALSE} +| ${container_chain_topology}= | chain +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${container_cpus}= | ${5} + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD switching with VLAN and uses ${phy_cores}\ +| | ... | physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_limit} | ${framesize} | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 Bridge Domain with memif pairs and VLAN in circular topology +| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite} +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/container_memif/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr.robot b/tests/vpp/perf/container_memif/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr.robot new file mode 100644 index 0000000000..e8d6c0a46d --- /dev/null +++ b/tests/vpp/perf/container_memif/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr.robot @@ -0,0 +1,154 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR +| ... | NIC_Intel-XXV710 | DOT1Q | L2BDMACLRN | BASE | MEMIF | DOCKER +| ... +| Suite Setup | Run Keywords +| ... | Set up 2-node performance topology with DUT's NIC model | L2 +| ... | Intel-XXV710 +| ... | AND | Set up performance test suite with MEMIF +| ... | AND | Set up performance topology with containers +| ... +| Suite Teardown | Tear down 2-node performance topology with container +| ... +| Test Setup | Run Keywords +| ... | Set up performance test +| ... | AND | Restart VPP in all 'VNF' containers +| ... +| Test Teardown | Tear down performance mrr test +| ... +| Test Template | Local Template +| ... +| Documentation | *Raw results L2BD with memif and IEEE 802.1Q test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\ +| ... | single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain. IEEE\ +| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with two L2 bridge\ +| ... | domains and MAC learning enabled. Container is connected to VPP via\ +| ... | Memif interface. Container is running same VPP version as running\ +| ... | on DUT. Container is limited via cgroup to use 3 cores allocated from\ +| ... | pool of isolated CPUs. There are no memory constraints. DUT1 is tested\ +| ... | with 2p25GE NIC XXV710 by Intel. +| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\ +| ... | at line rate and reports total received/sent packets over trial period.\ +| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\ +| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\ +| ... | flow-group) with all packets containing Ethernet header, IPv4 header\ +| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\ +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${subid}= | 10 +| ${tag_rewrite}= | pop-1 +| ${bd_id1}= | 1 +| ${bd_id2}= | 2 +| ${overhead}= | ${4} +# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps +| ${s_24.5G}= | ${24500000000} +# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps +| ${s_18.75Mpps}= | ${18750000} +# Traffic profile: +| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254 +# LXC container +| ${container_count}= | ${1} +| ${container_engine}= | Docker +| ${container_image}= | ubuntu:xenial-20180412 +| ${container_install_dkms}= | ${FALSE} +| ${container_chain_topology}= | chain +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${container_cpus}= | ${5} + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD switching with VLAN and uses ${phy_cores}\ +| | ... | physical core(s) for worker threads. +| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\ +| | ... | trial throughput test. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps} +| | ... | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 Bridge Domain with memif pairs and VLAN in circular topology +| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite} +| | Then Traffic should pass with maximum rate +| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile} + +*** Test Cases *** +| tc01-64B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-mrr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} diff --git a/tests/vpp/perf/container_memif/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr.robot b/tests/vpp/perf/container_memif/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr.robot new file mode 100644 index 0000000000..a2b72cf6cb --- /dev/null +++ b/tests/vpp/perf/container_memif/2n1l-25ge2p1xxv710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr.robot @@ -0,0 +1,161 @@ +# Copyright (c) 2018 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance/performance_setup.robot +| ... +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR +| ... | NIC_Intel-XXV710 | DOT1Q | L2BDMACLRN | BASE | MEMIF | DOCKER +| ... +| Suite Setup | Run Keywords +| ... | Set up 2-node performance topology with DUT's NIC model | L2 +| ... | Intel-XXV710 +| ... | AND | Set up performance test suite with MEMIF +| ... | AND | Set up performance topology with containers +| ... +| Suite Teardown | Tear down 2-node performance topology with container +| ... +| Test Setup | Run Keywords +| ... | Set up performance test +| ... | AND | Restart VPP in all 'VNF' containers +| ... +| Test Teardown | Tear down performance discovery test | ${min_rate}pps +| ... | ${framesize} | ${traffic_profile} +| ... +| Test Template | Local Template +| ... +| Documentation | *RFC2544: Pkt throughput L2BD with memif and IEEE 802.1Q test +| ... | cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with\ +| ... | single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 bridge domain. IEEE\ +| ... | 802.1Q tagging is applied on link between DUT1-if2 and TG-if2. +| ... | *[Cfg] DUT configuration:* DUT1 is configured with two L2 bridge\ +| ... | domains and MAC learning enabled. Container is connected to VPP via\ +| ... | Memif interface. Container is running same VPP version as running\ +| ... | on DUT. Container is limited via cgroup to use 3 cores allocated from\ +| ... | pool of isolated CPUs. There are no memory constraints. DUT1 is tested\ +| ... | with 2p25GE NIC XXV710 by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using MLRsearch library. Test packets are\ +| ... | generated by TG on links to DUT1. TG traffic profile contains two L3\ +| ... | flow-groups (flow-group per direction, 254 flows per flow-group) with\ +| ... | all packets containing Ethernet header, IPv4 header with IP\ +| ... | protocol=61 and static payload. MAC addresses are matching MAC\ +| ... | addresses of the TG node interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +| ${subid}= | 10 +| ${tag_rewrite}= | pop-1 +| ${bd_id1}= | 1 +| ${bd_id2}= | 2 +| ${overhead}= | ${4} +# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps +| ${s_24.5G}= | ${24500000000} +# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps +| ${s_18.75Mpps}= | ${18750000} +# Traffic profile: +| ${traffic_profile}= | trex-sl-2n-dot1qip4asym-ip4src254 +# LXC container +| ${container_count}= | ${1} +| ${container_engine}= | Docker +| ${container_image}= | ubuntu:xenial-20180412 +| ${container_install_dkms}= | ${FALSE} +| ${container_chain_topology}= | chain +# CPU settings +| ${system_cpus}= | ${1} +| ${vpp_cpus}= | ${5} +| ${container_cpus}= | ${5} + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] Each DUT runs L2BD switching with VLAN and uses ${phy_cores}\ +| | ... | physical core(s) for worker threads. +| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm. +| | ... +| | ... | *Arguments:* +| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1). +| | ... | Type: integer, string +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | ... +| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None} +| | ... +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} | ${10000} +| | ... +| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq} +| | And Add PCI devices to all DUTs +| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg +| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps} +| | ... | overhead=${overhead} +| | And Apply startup configuration on all VPP DUTs +| | When Initialize L2 Bridge Domain with memif pairs and VLAN in circular topology +| | ... | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite} +| | Then Find NDR and PDR intervals using optimized search +| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate} + +*** Test Cases *** +| tc01-64B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 64B | 1C +| | framesize=${64} | phy_cores=${1} + +| tc02-64B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 64B | 2C +| | framesize=${64} | phy_cores=${2} + +| tc03-64B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 64B | 4C +| | framesize=${64} | phy_cores=${4} + +| tc04-1518B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 1518B | 1C +| | framesize=${1518} | phy_cores=${1} + +| tc05-1518B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 1518B | 2C +| | framesize=${1518} | phy_cores=${2} + +| tc06-1518B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 1518B | 4C +| | framesize=${1518} | phy_cores=${4} + +| tc07-9000B-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 9000B | 1C +| | framesize=${9000} | phy_cores=${1} + +| tc08-9000B-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 9000B | 2C +| | framesize=${9000} | phy_cores=${2} + +| tc09-9000B-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | 9000B | 4C +| | framesize=${9000} | phy_cores=${4} + +| tc10-IMIX-1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | IMIX | 1C +| | framesize=IMIX_v4_1 | phy_cores=${1} + +| tc11-IMIX-2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | IMIX | 2C +| | framesize=IMIX_v4_1 | phy_cores=${2} + +| tc12-IMIX-4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr +| | [Tags] | IMIX | 4C +| | framesize=IMIX_v4_1 | phy_cores=${4} |