diff options
Diffstat (limited to 'tests')
12 files changed, 694 insertions, 15 deletions
diff --git a/tests/vpp/device/srv6/eth2p-ethip6ip6-ip6base-srv6enc1sid-dev.robot b/tests/vpp/device/srv6/eth2p-ethip6ip6-ip6base-srv6enc1sid-dev.robot new file mode 100644 index 0000000000..2b96ebc4ff --- /dev/null +++ b/tests/vpp/device/srv6/eth2p-ethip6ip6-ip6base-srv6enc1sid-dev.robot @@ -0,0 +1,103 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV | SCAPY +| ... | NIC_Virtual | ETH | IP6FWD | FEATURE | SRv6 | SRv6_1SID | DRV_VFIO_PCI +| ... | RXQ_SIZE_0 | TXQ_SIZE_0 +| ... | ethip6ip6-ip6base-srv6enc1sid +| +| Suite Setup | Setup suite topology interfaces | scapy +| Test Setup | Setup test +| Test Teardown | Tear down test | packet_trace +| +| Test Template | Local Template +| +| Documentation | *Segment routing over IPv6 dataplane with one SID\ +| ... | (SRH not inserted) test suite.* +| +| ... | *[Top] Network topologies:* TG-DUT1 2-node topology with one link\ +| ... | between nodes. +| ... | *[Cfg] DUT configuration:* On DUT1 configure physical interface IPv6\ +| ... | addresses, static ARP record, route and IPv6 forwarding over SRv6\ +| ... | with one SID - Segment Routing Header not inserted. +| ... | *[Ver] TG verification:* ETH-IP6 packet is sent from TG to DUT1 in one\ +| ... | direction. Packet is received and verified for correctness on TG. Then\ +| ... | ETH-IP6-IP6 packet is sent from TG in opposite direction. Packet is\ +| ... | received and verified for correctness on TG. +| ... | *[Ref] Applicable standard specifications:* SRv6 Network Programming -\ +| ... | draft 3. + +*** Variables *** +| @{plugins_to_enable}= | dpdk_plugin.so +| ${crypto_type}= | ${None} +| ${nic_name}= | virtual +| ${nic_driver}= | vfio-pci +| ${nic_rxq_size}= | 0 +| ${nic_txq_size}= | 0 +| ${nic_pfs}= | 2 +| ${nic_vfs}= | 0 +| ${overhead}= | ${40} +# SIDs +| ${dut1_sid1}= | 2002:1:: +| ${dut1_sid2}= | 2003:2:: +| ${dut1_bsid}= | 2002:1::1 +| ${dut2_sid1}= | 2002:2:: +| ${dut2_sid2}= | 2003:1:: +| ${sid_prefix}= | ${64} +# IP settings +| ${tg_if1_ip6_subnet}= | 2001:1:: +| ${tg_if2_ip6_subnet}= | 2001:2:: +| ${dst_addr_nr}= | ${1} +| ${dut1_if1_ip6}= | 2001:1::1 +| ${dut1_if2_ip6}= | 2001:3::1 +| ${dut2_if1_ip6}= | 2001:3::2 +| ${dut2_if2_ip6}= | 2001:2::1 +| ${prefix}= | ${64} + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT1 is configured with IPv6 routing and static route,\ +| | ... | SR policy and steering policy for one direction and one SR\ +| | ... | behaviour (function) - End.DX6 - for other direction. +| | ... | [Ver] Make TG send IPv6 packets routed over DUT1 interfaces.\ +| | ... | Make TG verify IPv6 packets are correct. +| | +| | ... | *Arguments:* +| | ... | - frame_size - Framesize in Bytes in integer. Type: integer +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | +| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} +| | +| | Set Test Variable | \${frame_size} +| | +| | Given Set Max Rate And Jumbo +| | And Add worker threads to all DUTs | ${phy_cores} | ${rxq} +| | And Pre-initialize layer driver | ${nic_driver} +| | And Apply startup configuration on all VPP DUTs | with_trace=${True} +| | When Initialize layer driver | ${nic_driver} +| | And Initialize layer interface +| | And Initialize SRv6 encapsulation with '1' x SID 'with' decapsulation +| | Then Send IPv6 Packet and verify SRv6 encapsulation in received packet +| | ... | ${tg} | ${TG_pf1}[0] | ${TG_pf2}[0] | ${DUT1_${int}1_mac}[0] +| | ... | ${DUT1_${int}2_mac}[0] | ${tg_if1_ip6_subnet}2 | ${tg_if2_ip6_subnet}2 +| | ... | ${dut1_sid1} | ${dut1_sid2} | ${dut2_sid2} | ${dut2_sid1} + +*** Test Cases *** +| tc01-78B-ethip6ip6-ip6base-srv6enc1sid-dev +| | [Tags] | 78B +| | frame_size=${78} | phy_cores=${0} diff --git a/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6enc2sids-dev.robot b/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6enc2sids-dev.robot new file mode 100644 index 0000000000..71618e5c0d --- /dev/null +++ b/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6enc2sids-dev.robot @@ -0,0 +1,107 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV | SCAPY +| ... | NIC_Virtual | ETH | IP6FWD | FEATURE | SRv6 | SRv6_2SID_DECAP +| ... | DRV_VFIO_PCI +| ... | RXQ_SIZE_0 | TXQ_SIZE_0 +| ... | ethip6srhip6-ip6base-srv6enc2sids +| +| Suite Setup | Setup suite topology interfaces | scapy +| Test Setup | Setup test +| Test Teardown | Tear down test | packet_trace +| +| Test Template | Local Template +| +| Documentation | *Segment routing over IPv6 dataplane with two SIDs\ +| ... | (SRH inserted) test suite.* +| +| ... | *[Top] Network topologies:* TG-DUT1 2-node topology with one link\ +| ... | between nodes. +| ... | *[Cfg] DUT configuration:* On DUT1 configure physical interface IPv6\ +| ... | addresses, static ARP record, route and IPv6 forwarding over SRv6\ +| ... | with two SIDs - Segment Routing Header inserted. +| ... | *[Ver] TG verification:* ETH-IP6 packet is sent from TG to DUT1 in one\ +| ... | direction. Packet is received and verified for correctness on TG. Then\ +| ... | ETH-IP6-IP6 packet is sent from TG in opposite direction. Packet is\ +| ... | received and verified for correctness on TG. +| ... | *[Ref] Applicable standard specifications:* SRv6 Network Programming -\ +| ... | draft 3. + +*** Variables *** +| @{plugins_to_enable}= | dpdk_plugin.so +| ${crypto_type}= | ${None} +| ${nic_name}= | virtual +| ${nic_driver}= | vfio-pci +| ${nic_rxq_size}= | 0 +| ${nic_txq_size}= | 0 +| ${nic_pfs}= | 2 +| ${nic_vfs}= | 0 +| ${overhead}= | ${80} +# SIDs +| ${dut1_sid1}= | 2002:1:: +| ${dut1_sid2_1}= | 2003:2:: +| ${dut1_sid2_2}= | 2003:3:: +| ${dut1_bsid}= | 2002:1::1 +| ${dut2_sid1_1}= | 2002:2:: +| ${dut2_sid1_2}= | 2002:3:: +| ${dut2_sid2}= | 2003:1:: +| ${sid_prefix}= | ${64} +# IP settings +| ${tg_if1_ip6_subnet}= | 2001:1:: +| ${tg_if2_ip6_subnet}= | 2001:2:: +| ${dst_addr_nr}= | ${1} +| ${dut1_if1_ip6}= | 2001:1::1 +| ${dut1_if2_ip6}= | 2001:3::1 +| ${dut2_if1_ip6}= | 2001:3::2 +| ${dut2_if2_ip6}= | 2001:2::1 +| ${prefix}= | ${64} + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT1 is configured with IPv6 routing and static route,\ +| | ... | SR policy and steering policy for one direction and two SR\ +| | ... | behaviours (functions) - End and End.DX6 - for other direction. +| | ... | [Ver] Make TG send IPv6 packets routed over DUT1 interfaces.\ +| | ... | Make TG verify IPv6 packets are correct. +| | +| | ... | *Arguments:* +| | ... | - frame_size - Framesize in Bytes in integer. Type: integer +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | +| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} +| | +| | Set Test Variable | \${frame_size} +| | +| | Given Set Max Rate And Jumbo +| | And Add worker threads to all DUTs | ${phy_cores} | ${rxq} +| | And Pre-initialize layer driver | ${nic_driver} +| | And Apply startup configuration on all VPP DUTs | with_trace=${True} +| | When Initialize layer driver | ${nic_driver} +| | And Initialize layer interface +| | And Initialize SRv6 encapsulation with '2' x SID 'with' decapsulation +| | Then Send IPv6 Packet and verify SRv6 encapsulation in received packet +| | ... | ${tg} | ${TG_pf1}[0] | ${TG_pf2}[0] | ${DUT1_${int}1_mac}[0] +| | ... | ${DUT1_${int}2_mac}[0] | ${tg_if1_ip6_subnet}2 | ${tg_if2_ip6_subnet}2 +| | ... | ${dut1_sid1} | ${dut1_sid2_1} | ${dut2_sid2} | ${dut2_sid1_1} +| | ... | ${dut1_sid2_2} | ${dut2_sid1_2} + +*** Test Cases *** +| tc01-78B-ethip6srhip6-ip6base-srv6enc2sids-dev +| | [Tags] | 78B +| | frame_size=${78} | phy_cores=${0} diff --git a/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6enc2sids-nodecaps-dev.robot b/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6enc2sids-nodecaps-dev.robot new file mode 100644 index 0000000000..c8a66db69e --- /dev/null +++ b/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6enc2sids-nodecaps-dev.robot @@ -0,0 +1,107 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV | SCAPY +| ... | NIC_Virtual | ETH | IP6FWD | FEATURE | SRv6 | SRv6_2SID_NODECAP +| ... | DRV_VFIO_PCI +| ... | RXQ_SIZE_0 | TXQ_SIZE_0 +| ... | ethip6srhip6-ip6base-srv6enc2sids-nodecaps +| +| Suite Setup | Setup suite topology interfaces | scapy +| Test Setup | Setup test +| Test Teardown | Tear down test | packet_trace +| +| Test Template | Local Template +| +| Documentation | *Segment routing over IPv6 dataplane with two SIDs\ +| ... | (SRH inserted) test suite.* +| +| ... | *[Top] Network topologies:* TG-DUT1 2-node topology with one link\ +| ... | between nodes. +| ... | *[Cfg] DUT configuration:* On DUT1 configure physical interface IPv6\ +| ... | addresses, static ARP record, route and IPv6 forwarding over SRv6\ +| ... | with two SIDs - Segment Routing Header inserted. +| ... | *[Ver] TG verification:* ETH-IP6 packet is sent from TG to DUT1 in one\ +| ... | direction. Packet is received and verified for correctness on TG. Then\ +| ... | ETH-IP6-IP6 packet is sent from TG in opposite direction. Packet is\ +| ... | received and verified for correctness on TG. +| ... | *[Ref] Applicable standard specifications:* SRv6 Network Programming -\ +| ... | draft 3. + +*** Variables *** +| @{plugins_to_enable}= | dpdk_plugin.so +| ${crypto_type}= | ${None} +| ${nic_name}= | virtual +| ${nic_driver}= | vfio-pci +| ${nic_rxq_size}= | 0 +| ${nic_txq_size}= | 0 +| ${nic_pfs}= | 2 +| ${nic_vfs}= | 0 +| ${overhead}= | ${80} +# SIDs +| ${dut1_sid1}= | 2002:1:: +| ${dut1_sid2_1}= | 2003:2:: +| ${dut1_sid2_2}= | 2003:3:: +| ${dut1_bsid}= | 2002:1::1 +| ${dut2_sid1_1}= | 2002:2:: +| ${dut2_sid1_2}= | 2002:3:: +| ${dut2_sid2}= | 2003:1:: +| ${sid_prefix}= | ${64} +# IP settings +| ${tg_if1_ip6_subnet}= | 2001:1:: +| ${tg_if2_ip6_subnet}= | 2001:2:: +| ${dst_addr_nr}= | ${1} +| ${dut1_if1_ip6}= | 2001:1::1 +| ${dut1_if2_ip6}= | 2001:3::1 +| ${dut2_if1_ip6}= | 2001:3::2 +| ${dut2_if2_ip6}= | 2001:2::1 +| ${prefix}= | ${64} + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT1 is configured with IPv6 routing and static route,\ +| | ... | SR policy and steering policy for one direction and one SR\ +| | ... | behaviour (function) - End - for other direction. +| | ... | [Ver] Make TG send IPv6 packets routed over DUT1 interfaces.\ +| | ... | Make TG verify IPv6 packets are correct. +| | +| | ... | *Arguments:* +| | ... | - frame_size - Framesize in Bytes in integer. Type: integer +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | +| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} +| | +| | Set Test Variable | \${frame_size} +| | +| | Given Set Max Rate And Jumbo +| | And Add worker threads to all DUTs | ${phy_cores} | ${rxq} +| | And Pre-initialize layer driver | ${nic_driver} +| | And Apply startup configuration on all VPP DUTs | with_trace=${True} +| | When Initialize layer driver | ${nic_driver} +| | And Initialize layer interface +| | And Initialize SRv6 encapsulation with '2' x SID 'without' decapsulation +| | Then Send IPv6 Packet and verify SRv6 encapsulation in received packet +| | ... | ${tg} | ${TG_pf1}[0] | ${TG_pf2}[0] | ${DUT1_${int}1_mac}[0] +| | ... | ${DUT1_${int}2_mac}[0] | ${tg_if1_ip6_subnet}2 | ${tg_if2_ip6_subnet}2 +| | ... | ${dut1_sid1} | ${dut1_sid2_1} | ${dut2_sid2} | ${dut2_sid1_1} +| | ... | ${dut1_sid2_2} | ${dut2_sid1_2} | decap=${False} + +*** Test Cases *** +| tc01-78B-ethip6srhip6-ip6base-srv6enc2sids-nodecaps-dev +| | [Tags] | 78B +| | frame_size=${78} | phy_cores=${0} diff --git a/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6proxy-dyn-dev.robot b/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6proxy-dyn-dev.robot new file mode 100644 index 0000000000..80c145d111 --- /dev/null +++ b/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6proxy-dyn-dev.robot @@ -0,0 +1,121 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV | SCAPY +| ... | NIC_Virtual | ETH | IP6FWD | FEATURE | SRv6 | SRv6_PROXY +| ... | SRv6_PROXY_DYN | MEMIF | DOCKER | DRV_VFIO_PCI +| ... | RXQ_SIZE_0 | TXQ_SIZE_0 +| ... | ethip6srhip6-ip6base-srv6proxy-dyn +| +| Suite Setup | Setup suite topology interfaces | scapy +| Test Setup | Setup test +| Test Teardown | Tear down test | packet_trace | container +| +| Test Template | Local Template +| +| Documentation | *Segment routing over IPv6 dataplane with Dynamic\ +| ... | SRv6 proxy test suite.* +| +| ... | *[Top] Network topologies:* TG-DUT1 2-node topology with one link\ +| ... | between nodes. +| ... | *[Cfg] DUT configuration:* On DUT1 configure physical interface IPv6\ +| ... | addresses, static ARP record, route and IPv6 forwarding over SRv6\ +| ... | with three SIDs - Segment Routing Header inserted. +| ... | *[Ver] TG verification:* ETH-IP6 packet is sent from TG to DUT1 in one\ +| ... | direction. Packet is received and verified for correctness on TG. Then\ +| ... | ETH-IP6-IP6 packet is sent from TG in opposite direction. Packet is\ +| ... | received and verified for correctness on TG. +| ... | *[Ref] Applicable standard specifications:* SRv6 Network Programming -\ +| ... | draft 3. + +*** Variables *** +| @{plugins_to_enable}= | dpdk_plugin.so | memif_plugin.so | srv6ad_plugin.so +| ${crypto_type}= | ${None} +| ${nic_name}= | virtual +| ${nic_driver}= | vfio-pci +| ${nic_rxq_size}= | 0 +| ${nic_txq_size}= | 0 +| ${nic_pfs}= | 2 +| ${nic_vfs}= | 0 +| ${overhead}= | ${80} +# SIDs +| ${dut1_sid1}= | 2002:1:: +| ${dut1_sid2}= | 2003:2:: +| ${dut1_bsid}= | 2002:1::1 +| ${dut2_sid1}= | 2002:2:: +| ${dut2_sid2}= | 2003:1:: +| ${out_sid1_1}= | 2002:3:: +| ${out_sid1_2}= | 2002:4:: +| ${out_sid2_1}= | 2003:3:: +| ${out_sid2_2}= | 2003:4:: +| ${sid_prefix}= | ${64} +# IP settings +| ${tg_if1_ip6_subnet}= | 2001:1:: +| ${tg_if2_ip6_subnet}= | 2001:2:: +| ${dst_addr_nr}= | ${1} +| ${dut1_if1_ip6}= | 2001:1::1 +| ${dut1_if2_ip6}= | 2001:3::1 +| ${dut1-memif-1-if1_ip6}= | 3001:1::1 +| ${dut1-memif-1-if2_ip6}= | 3001:1::2 +| ${dut1_nh}= | 4002:: +| ${dut2_if1_ip6}= | 2001:3::2 +| ${dut2_if2_ip6}= | 2001:2::1 +| ${dut2-memif-1-if1_ip6}= | 3002:1::1 +| ${dut2-memif-1-if2_ip6}= | 3002:1::2 +| ${dut2_nh}= | 4001:: +| ${prefix}= | ${64} +| ${mem_prefix}= | ${128} +# Container +| ${container_engine}= | Docker +| ${container_chain_topology}= | chain_functional + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT1 is configured with IPv6 routing and static route,\ +| | ... | SR policy and steering policy for one direction and one SR\ +| | ... | behaviour (function) - End.AD - for other direction. +| | ... | [Ver] Make TG send IPv6 packets routed over DUT1 interfaces.\ +| | ... | Make TG verify IPv6 packets are correct. +| | +| | ... | *Arguments:* +| | ... | - frame_size - Framesize in Bytes in integer. Type: integer +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | +| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} +| | +| | Set Test Variable | \${frame_size} +| | +| | Given Set Max Rate And Jumbo +| | And Add worker threads to all DUTs | ${phy_cores} | ${rxq} +| | And Pre-initialize layer driver | ${nic_driver} +| | And Apply startup configuration on all VPP DUTs | with_trace=${True} +| | When Initialize layer driver | ${nic_driver} +| | And Initialize layer interface +| | And Start containers for test | auto_scale=${False} | pinning=${False} +| | And Initialize SRv6 with 'dynamic_proxy' SR-unaware Service Function +| | Then Send IPv6 Packet and verify SRv6 encapsulation in received packet +| | ... | ${tg} | ${TG_pf1}[0] | ${TG_pf2}[0] | ${DUT1_${int}1_mac}[0] +| | ... | ${DUT1_${int}2_mac}[0] | ${tg_if1_ip6_subnet}2 | ${tg_if2_ip6_subnet}2 +| | ... | ${dut1_sid1} | ${dut1_sid2} | ${dut2_sid2} | ${dut2_sid1} +| | ... | ${out_sid2_1} | ${out_sid1_1} | decap=${False} +| | ... | tg_dstsid3=${out_sid1_2} | dut_dstsid3=${out_sid2_2} + +*** Test Cases *** +| tc01-78B-ethip6srhip6-ip6base-srv6proxy-dyn-dev +| | [Tags] | 78B +| | frame_size=${78} | phy_cores=${0} diff --git a/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6proxy-masq-dev.robot b/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6proxy-masq-dev.robot new file mode 100644 index 0000000000..fce94a2808 --- /dev/null +++ b/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6proxy-masq-dev.robot @@ -0,0 +1,121 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV | SCAPY +| ... | NIC_Virtual | ETH | IP6FWD | FEATURE | SRv6 | SRv6_PROXY +| ... | SRv6_PROXY_MASQ | MEMIF | DOCKER | DRV_VFIO_PCI +| ... | RXQ_SIZE_0 | TXQ_SIZE_0 +| ... | ethip6srhip6-ip6base-srv6proxy-masq +| +| Suite Setup | Setup suite topology interfaces | scapy +| Test Setup | Setup test +| Test Teardown | Tear down test | packet_trace | container +| +| Test Template | Local Template +| +| Documentation | *Segment routing over IPv6 dataplane with Masquerading\ +| ... | SRv6 proxy test cases* +| +| ... | *[Top] Network topologies:* TG-DUT1 2-node topology with one link\ +| ... | between nodes. +| ... | *[Cfg] DUT configuration:* On DUT1 configure physical interface IPv6\ +| ... | addresses, static ARP record, route and IPv6 forwarding over SRv6\ +| ... | with three SIDs - Segment Routing Header inserted. +| ... | *[Ver] TG verification:* ETH-IP6 packet is sent from TG to DUT1 in one\ +| ... | direction. Packet is received and verified for correctness on TG. Then\ +| ... | ETH-IP6-IP6 packet is sent from TG in opposite direction. Packet is\ +| ... | received and verified for correctness on TG. +| ... | *[Ref] Applicable standard specifications:* SRv6 Network Programming -\ +| ... | draft 3. + +*** Variables *** +| @{plugins_to_enable}= | dpdk_plugin.so | memif_plugin.so | srv6am_plugin.so +| ${crypto_type}= | ${None} +| ${nic_name}= | virtual +| ${nic_driver}= | vfio-pci +| ${nic_rxq_size}= | 0 +| ${nic_txq_size}= | 0 +| ${nic_pfs}= | 2 +| ${nic_vfs}= | 0 +| ${overhead}= | ${80} +# SIDs +| ${dut1_sid1}= | 2002:1:: +| ${dut1_sid2}= | 2003:2:: +| ${dut1_bsid}= | 2002:1::1 +| ${dut2_sid1}= | 2002:2:: +| ${dut2_sid2}= | 2003:1:: +| ${out_sid1_1}= | 2002:3:: +| ${out_sid1_2}= | 2002:4:: +| ${out_sid2_1}= | 2003:3:: +| ${out_sid2_2}= | 2003:4:: +| ${sid_prefix}= | ${64} +# IP settings +| ${tg_if1_ip6_subnet}= | 2001:1:: +| ${tg_if2_ip6_subnet}= | 2001:2:: +| ${dst_addr_nr}= | ${1} +| ${dut1_if1_ip6}= | 2001:1::1 +| ${dut1_if2_ip6}= | 2001:3::1 +| ${dut1-memif-1-if1_ip6}= | 3001:1::1 +| ${dut1-memif-1-if2_ip6}= | 3001:1::2 +| ${dut1_nh}= | 4002:: +| ${dut2_if1_ip6}= | 2001:3::2 +| ${dut2_if2_ip6}= | 2001:2::1 +| ${dut2-memif-1-if1_ip6}= | 3002:1::1 +| ${dut2-memif-1-if2_ip6}= | 3002:1::2 +| ${dut2_nh}= | 4001:: +| ${prefix}= | ${64} +| ${mem_prefix}= | ${128} +# Container +| ${container_engine}= | Docker +| ${container_chain_topology}= | chain_functional + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT1 is configured with IPv6 routing and static route,\ +| | ... | SR policy and steering policy for one direction and one SR\ +| | ... | behaviour (function) - End.AM - for other direction. +| | ... | [Ver] Make TG send IPv6 packets routed over DUT1 interfaces.\ +| | ... | Make TG verify IPv6 packets are correct. +| | +| | ... | *Arguments:* +| | ... | - frame_size - Framesize in Bytes in integer. Type: integer +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | +| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} +| | +| | Set Test Variable | \${frame_size} +| | +| | Given Set Max Rate And Jumbo +| | And Add worker threads to all DUTs | ${phy_cores} | ${rxq} +| | And Pre-initialize layer driver | ${nic_driver} +| | And Apply startup configuration on all VPP DUTs | with_trace=${True} +| | When Initialize layer driver | ${nic_driver} +| | And Initialize layer interface +| | And Start containers for test | auto_scale=${False} | pinning=${False} +| | And Initialize SRv6 with 'masquerading' SR-unaware Service Function +| | Then Send IPv6 Packet and verify SRv6 encapsulation in received packet +| | ... | ${tg} | ${TG_pf1}[0] | ${TG_pf2}[0] | ${DUT1_${int}1_mac}[0] +| | ... | ${DUT1_${int}2_mac}[0] | ${tg_if1_ip6_subnet}2 | ${tg_if2_ip6_subnet}2 +| | ... | ${dut1_sid1} | ${dut1_sid2} | ${dut2_sid2} | ${dut2_sid1} +| | ... | ${out_sid2_1} | ${out_sid1_1} | decap=${False} +| | ... | tg_dstsid3=${out_sid1_2} | dut_dstsid3=${out_sid2_2} + +*** Test Cases *** +| tc01-78B-ethip6srhip6-ip6base-srv6proxy-masq-dev +| | [Tags] | 78B +| | frame_size=${78} | phy_cores=${0} diff --git a/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6proxy-stat-dev.robot b/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6proxy-stat-dev.robot new file mode 100644 index 0000000000..3c669b4f41 --- /dev/null +++ b/tests/vpp/device/srv6/eth2p-ethip6srhip6-ip6base-srv6proxy-stat-dev.robot @@ -0,0 +1,122 @@ +# Copyright (c) 2020 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/shared/default.robot +| +| Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV | SCAPY +| ... | NIC_Virtual | ETH | IP6FWD | FEATURE | SRv6 | SRv6_PROXY +| ... | SRv6_PROXY_STAT | MEMIF | DOCKER | DRV_VFIO_PCI +| ... | RXQ_SIZE_0 | TXQ_SIZE_0 +| ... | ethip6srhip6-ip6base-srv6proxy-stat +| +| Suite Setup | Setup suite topology interfaces | scapy +| Test Setup | Setup test +| Test Teardown | Tear down test | packet_trace | container +| +| Test Template | Local Template +| +| Documentation | *Segment routing over IPv6 dataplane with Static\ +| ... | SRv6 proxy test cases.* +| +| ... | *[Top] Network topologies:* TG-DUT1 2-node topology with one link\ +| ... | between nodes. +| ... | *[Cfg] DUT configuration:* On DUT1 configure physical interface IPv6\ +| ... | addresses, static ARP record, route and IPv6 forwarding over SRv6\ +| ... | with three SIDs - Segment Routing Header inserted. +| ... | *[Ver] TG verification:* ETH-IP6 packet is sent from TG to DUT1 in one\ +| ... | direction. Packet is received and verified for correctness on TG. Then\ +| ... | ETH-IP6-IP6 packet is sent from TG in opposite direction. Packet is\ +| ... | received and verified for correctness on TG. +| ... | *[Ref] Applicable standard specifications:* SRv6 Network Programming -\ +| ... | draft 3. + +*** Variables *** +| @{plugins_to_enable}= | dpdk_plugin.so | memif_plugin.so | srv6as_plugin.so +| ${crypto_type}= | ${None} +| ${nic_name}= | virtual +| ${nic_driver}= | vfio-pci +| ${nic_rxq_size}= | 0 +| ${nic_txq_size}= | 0 +| ${nic_pfs}= | 2 +| ${nic_vfs}= | 0 +| ${overhead}= | ${80} +# SIDs +| ${dut1_sid1}= | 2002:1:: +| ${dut1_sid2}= | 2003:2:: +| ${dut1_bsid}= | 2002:1::1 +| ${dut2_sid1}= | 2002:2:: +| ${dut2_sid2}= | 2003:1:: +| ${out_sid1_1}= | 2002:3:: +| ${out_sid1_2}= | 2002:4:: +| ${out_sid2_1}= | 2003:3:: +| ${out_sid2_2}= | 2003:4:: +| ${sid_prefix}= | ${64} +# IP settings +| ${tg_if1_ip6_subnet}= | 2001:1:: +| ${tg_if2_ip6_subnet}= | 2001:2:: +| ${dst_addr_nr}= | ${1} +| ${dut1_if1_ip6}= | 2001:1::1 +| ${dut1_if2_ip6}= | 2001:3::1 +| ${dut1-memif-1-if1_ip6}= | 3001:1::1 +| ${dut1-memif-1-if2_ip6}= | 3001:1::2 +| ${dut1_nh}= | 4002:: +| ${dut2_if1_ip6}= | 2001:3::2 +| ${dut2_if2_ip6}= | 2001:2::1 +| ${dut2-memif-1-if1_ip6}= | 3002:1::1 +| ${dut2-memif-1-if2_ip6}= | 3002:1::2 +| ${dut2_nh}= | 4001:: +| ${prefix}= | ${64} +| ${mem_prefix}= | ${128} +# Container +| ${container_engine}= | Docker +| ${container_chain_topology}= | chain_functional + +*** Keywords *** +| Local Template +| | [Documentation] +| | ... | [Cfg] DUT1 is configured with IPv6 routing and static route,\ +| | ... | SR policy and steering policy for one direction and one SR\ +| | ... | behaviour (function) - End.AS - for other direction. +| | ... | [Ver] Make TG send IPv6 packets routed over DUT1 interfaces.\ +| | ... | Make TG verify IPv6 packets are correct. +| | +| | ... | *Arguments:* +| | ... | - frame_size - Framesize in Bytes in integer. Type: integer +| | ... | - phy_cores - Number of physical cores. Type: integer +| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer +| | +| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None} +| | +| | Set Test Variable | \${frame_size} +| | +| | Given Set Max Rate And Jumbo +| | And Add worker threads to all DUTs | ${phy_cores} | ${rxq} +| | And Pre-initialize layer driver | ${nic_driver} +| | And Apply startup configuration on all VPP DUTs | with_trace=${True} +| | When Initialize layer driver | ${nic_driver} +| | And Initialize layer interface +| | And Start containers for test | auto_scale=${False} | pinning=${False} +| | And Initialize SRv6 with 'static_proxy' SR-unaware Service Function +| | Then Send IPv6 Packet and verify SRv6 encapsulation in received packet +| | ... | ${tg} | ${TG_pf1}[0] | ${TG_pf2}[0] | ${DUT1_${int}1_mac}[0] +| | ... | ${DUT1_${int}2_mac}[0] | ${tg_if1_ip6_subnet}2 | ${tg_if2_ip6_subnet}2 +| | ... | ${dut1_sid1} | ${dut1_sid2} | ${dut2_sid2} | ${dut2_sid1} +| | ... | ${out_sid2_1} | ${out_sid1_1} | decap=${False} +| | ... | tg_dstsid3=${out_sid1_2} | dut_dstsid3=${out_sid2_2} +| | ... | static_proxy=${True} + +*** Test Cases *** +| tc01-78B-ethip6srhip6-ip6base-srv6proxy-stat-dev +| | [Tags] | 78B +| | frame_size=${78} | phy_cores=${0} diff --git a/tests/vpp/perf/srv6/10ge2p1x710-ethip6ip6-ip6base-srv6enc1sid-ndrpdr.robot b/tests/vpp/perf/srv6/10ge2p1x710-ethip6ip6-ip6base-srv6enc1sid-ndrpdr.robot index d2790c264b..20316a75fe 100644 --- a/tests/vpp/perf/srv6/10ge2p1x710-ethip6ip6-ip6base-srv6enc1sid-ndrpdr.robot +++ b/tests/vpp/perf/srv6/10ge2p1x710-ethip6ip6-ip6base-srv6enc1sid-ndrpdr.robot @@ -36,8 +36,8 @@ | ... | TG-DUTn for IPv6 routing over SRv6. | ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6\ | ... | routing and static route, SR policy and steering policy for one\ -| ... | direction and one SR behaviour (function) - End - for other direction.\ -| ... | DUT1 and DUT2 are tested with ${nic_name}.\ +| ... | direction and one SR behaviour (function) - End.DX6 - for other\ +| ... | direction. DUT1 and DUT2 are tested with ${nic_name}.\ | ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ | ... | Rate) with zero packet loss tolerance and throughput PDR (Partial Drop\ | ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ @@ -107,7 +107,7 @@ | | And Apply startup configuration on all VPP DUTs | | When Initialize layer driver | ${nic_driver} | | And Initialize layer interface -| | And Initialize IPv6 forwarding over SRv6 with encapsulation with '1' x SID 'with' decapsulation in 3-node circular topology +| | And Initialize SRv6 encapsulation with '1' x SID 'with' decapsulation | | Then Find NDR and PDR intervals using optimized search *** Test Cases *** diff --git a/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6enc2sids-ndrpdr.robot b/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6enc2sids-ndrpdr.robot index a37ffa6170..184a3c9e7b 100644 --- a/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6enc2sids-ndrpdr.robot +++ b/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6enc2sids-ndrpdr.robot @@ -90,7 +90,8 @@ | | [Documentation] | | ... | [Cfg] DUT1 and DUT2 are configured with IPv6\ | | ... | routing and static route, SR policy and steering policy for one\ -| | ... | direction and one SR behaviour (function) - End - for other direction. +| | ... | direction and two SR behaviours (functions) - End and End.DX6 - for\ +| | ... | other direction. | | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. | | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\ | | @@ -110,7 +111,7 @@ | | And Apply startup configuration on all VPP DUTs | | When Initialize layer driver | ${nic_driver} | | And Initialize layer interface -| | And Initialize IPv6 forwarding over SRv6 with encapsulation with '2' x SID 'with' decapsulation in 3-node circular topology +| | And Initialize SRv6 encapsulation with '2' x SID 'with' decapsulation | | Then Find NDR and PDR intervals using optimized search *** Test Cases *** diff --git a/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6enc2sids-nodecaps-ndrpdr.robot b/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6enc2sids-nodecaps-ndrpdr.robot index e260bf2789..6b8cfcc0d6 100644 --- a/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6enc2sids-nodecaps-ndrpdr.robot +++ b/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6enc2sids-nodecaps-ndrpdr.robot @@ -110,7 +110,7 @@ | | And Apply startup configuration on all VPP DUTs | | When Initialize layer driver | ${nic_driver} | | And Initialize layer interface -| | And Initialize IPv6 forwarding over SRv6 with encapsulation with '2' x SID 'without' decapsulation in 3-node circular topology +| | And Initialize SRv6 encapsulation with '2' x SID 'without' decapsulation | | Then Find NDR and PDR intervals using optimized search *** Test Cases *** diff --git a/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6proxy-dyn-ndrpdr.robot b/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6proxy-dyn-ndrpdr.robot index c38d2bdfcc..b17bb6b8b5 100644 --- a/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6proxy-dyn-ndrpdr.robot +++ b/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6proxy-dyn-ndrpdr.robot @@ -67,7 +67,6 @@ | ${dut1_sid2}= | 2003:2:: | ${dut1_bsid}= | 2002:1::1 | ${dut2_sid1}= | 2002:2:: -| ${dut2_sid1}= | 2002:2:: | ${dut2_sid2}= | 2003:1:: | ${dut2_bsid}= | 2003:1::1 | ${out_sid1_1}= | 2002:3:: @@ -102,7 +101,7 @@ | | [Documentation] | | ... | [Cfg] DUT1 and DUT2 are configured with IPv6\ | | ... | routing and static route, SR policy and steering policy for one\ -| | ... | direction and one SR behaviour (function) - End - for other direction. +| | ... | direction and SR behaviour (function) - End.AD - for other direction. | | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. | | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\ | | @@ -123,7 +122,7 @@ | | When Initialize layer driver | ${nic_driver} | | And Initialize layer interface | | And Start containers for test | nf_chains=${1} | nf_nodes=${1} -| | And Initialize IPv6 forwarding over SRv6 with endpoint to SR-unaware Service Function via 'dynamic_proxy' behaviour in 3-node circular topology +| | And Initialize SRv6 with 'dynamic_proxy' SR-unaware Service Function | | Then Find NDR and PDR intervals using optimized search *** Test Cases *** diff --git a/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6proxy-masq-ndrpdr.robot b/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6proxy-masq-ndrpdr.robot index 097c2ea16d..6d0f6693f0 100644 --- a/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6proxy-masq-ndrpdr.robot +++ b/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6proxy-masq-ndrpdr.robot @@ -67,7 +67,6 @@ | ${dut1_sid2}= | 2003:2:: | ${dut1_bsid}= | 2002:1::1 | ${dut2_sid1}= | 2002:2:: -| ${dut2_sid1}= | 2002:2:: | ${dut2_sid2}= | 2003:1:: | ${dut2_bsid}= | 2003:1::1 | ${out_sid1_1}= | 2002:3:: @@ -102,7 +101,7 @@ | | [Documentation] | | ... | [Cfg] DUT1 and DUT2 are configured with IPv6\ | | ... | routing and static route, SR policy and steering policy for one\ -| | ... | direction and one SR behaviour (function) - End - for other direction. +| | ... | direction and SR behaviour (function) - End.AM - for other direction. | | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. | | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\ | | @@ -123,7 +122,7 @@ | | When Initialize layer driver | ${nic_driver} | | And Initialize layer interface | | And Start containers for test | nf_chains=${1} | nf_nodes=${1} -| | And Initialize IPv6 forwarding over SRv6 with endpoint to SR-unaware Service Function via 'masquerading' behaviour in 3-node circular topology +| | And Initialize SRv6 with 'masquerading' SR-unaware Service Function | | Then Find NDR and PDR intervals using optimized search *** Test Cases *** diff --git a/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6proxy-stat-ndrpdr.robot b/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6proxy-stat-ndrpdr.robot index 2198d0d958..e820365995 100644 --- a/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6proxy-stat-ndrpdr.robot +++ b/tests/vpp/perf/srv6/10ge2p1x710-ethip6srhip6-ip6base-srv6proxy-stat-ndrpdr.robot @@ -67,7 +67,6 @@ | ${dut1_sid2}= | 2003:2:: | ${dut1_bsid}= | 2002:1::1 | ${dut2_sid1}= | 2002:2:: -| ${dut2_sid1}= | 2002:2:: | ${dut2_sid2}= | 2003:1:: | ${dut2_bsid}= | 2003:1::1 | ${out_sid1_1}= | 2002:3:: @@ -102,7 +101,7 @@ | | [Documentation] | | ... | [Cfg] DUT1 and DUT2 are configured with IPv6\ | | ... | routing and static route, SR policy and steering policy for one\ -| | ... | direction and one SR behaviour (function) - End - for other direction. +| | ... | direction and SR behaviour (function) - End.AS - for other direction. | | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads. | | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\ | | @@ -123,7 +122,7 @@ | | When Initialize layer driver | ${nic_driver} | | And Initialize layer interface | | And Start containers for test | nf_chains=${1} | nf_nodes=${1} -| | And Initialize IPv6 forwarding over SRv6 with endpoint to SR-unaware Service Function via 'static_proxy' behaviour in 3-node circular topology +| | And Initialize SRv6 with 'static_proxy' SR-unaware Service Function | | Then Find NDR and PDR intervals using optimized search *** Test Cases *** |