diff options
Diffstat (limited to 'tests')
| -rw-r--r-- | tests/perf/10ge2p1vic1227-eth-l2bdbasemaclrn-ndrdisc.robot | 286 |
1 files changed, 286 insertions, 0 deletions
diff --git a/tests/perf/10ge2p1vic1227-eth-l2bdbasemaclrn-ndrdisc.robot b/tests/perf/10ge2p1vic1227-eth-l2bdbasemaclrn-ndrdisc.robot new file mode 100644 index 0000000000..cdc07dd71e --- /dev/null +++ b/tests/perf/10ge2p1vic1227-eth-l2bdbasemaclrn-ndrdisc.robot @@ -0,0 +1,286 @@ +# Copyright (c) 2016 Cisco and/or its affiliates. +# Licensed under the Apache License, Version 2.0 (the "License"); +# you may not use this file except in compliance with the License. +# You may obtain a copy of the License at: +# +# http://www.apache.org/licenses/LICENSE-2.0 +# +# Unless required by applicable law or agreed to in writing, software +# distributed under the License is distributed on an "AS IS" BASIS, +# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +# See the License for the specific language governing permissions and +# limitations under the License. + +*** Settings *** +| Resource | resources/libraries/robot/performance.robot +| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC +| ... | NIC_Cisco-VIC-1227 | ETH | L2BDMACLRN | BASE +| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model +| ... | L2 | Cisco-VIC-1227 +| Suite Teardown | 3-node Performance Suite Teardown +| Test Setup | Setup all DUTs before test +| Test Teardown | Run Keywords +| ... | Run Keyword If Test Failed +| ... | Traffic should pass with no loss | 10 +| ... | ${min_rate}pps | ${framesize} | 3-node-bridge +| ... | fail_on_loss=${False} +| ... | AND | Remove startup configuration of VPP from all DUTs +| ... | AND | Show vpp trace dump on all DUTs +| Documentation | *RFC2544: Pkt throughput L2BD test cases* +| ... +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\ +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge-\ +| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC +| ... | Cisco-VIC-1227. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\ +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\ +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\ +| ... | of packets transmitted. NDR and PDR are discovered for different\ +| ... | Ethernet L2 frame sizes using either binary search or linear search\ +| ... | algorithms with configured starting rate and final step that determines\ +| ... | throughput measurement resolution. Test packets are generated by TG on\ +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\ +| ... | (flow-group per direction, 253 flows per flow-group) with all packets\ +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\ +| ... | payload. MAC addresses are matching MAC addresses of the TG node\ +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. + +*** Variables *** +# Cisco-VIC-1227 bandwidth limit +| ${s_limit} | ${10000000000} + +*** Keywords *** +| L2 Bridge Domain NDR Binary Search +| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq} +| | # Test Variables required for test teardown +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Set Test Documentation | [Cfg] DUT runs L2BD switching config with ${wt}\ +| | Set Test Documentation | thread, ${wt} phy core, ${rxq}\ | append=True +| | Set Test Documentation | receive queue per NIC port. | append=True +| | Set Test Documentation | [Ver] Find NDR for ${framesize} Byte\ | append=True +| | Set Test Documentation | frames using binary search start at\ | append=True +| | Set Test Documentation | 10GE linerate, step ${threshold}pps. | append=True +| | Add '${wt}' worker threads and rxqueues '${rxq}' in 3-node single-link topo +| | Add PCI devices to DUTs from 3-node single link topology +| | Run Keyword If | ${framesize} < ${1522} | Add No Multi Seg to all DUTs +| | Apply startup configuration on all VPP DUTs +| | L2 bridge domain initialized in a 3-node circular topology +| | Find NDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | 3-node-bridge +| | ... | ${min_rate} | ${max_rate} | ${threshold} + +| L2 Bridge Domain PDR Binary Search +| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq} +| | # Test Variables required for test teardown +| | Set Test Variable | ${framesize} +| | Set Test Variable | ${min_rate} +| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize} +| | ${binary_min}= | Set Variable | ${min_rate} +| | ${binary_max}= | Set Variable | ${max_rate} +| | ${threshold}= | Set Variable | ${min_rate} +| | Set Test Documentation | [Cfg] DUT runs L2BD switching config with ${wt}\ +| | Set Test Documentation | thread, ${wt} phy core, ${rxq}\ | append=True +| | Set Test Documentation | receive queue per NIC port. | append=True +| | Set Test Documentation | [Ver] Find PDR for ${framesize} Byte\ | append=True +| | Set Test Documentation | frames using binary search start at\ | append=True +| | Set Test Documentation | 10GE linerate, step ${threshold}pps, | append=True +| | Set Test Documentation | LT=${glob_loss_acceptance} | append=True +| | Set Test Documentation | ${glob_loss_acceptance_type}. | append=True +| | Add '${wt}' worker threads and rxqueues '${rxq}' in 3-node single-link topo +| | Add PCI devices to DUTs from 3-node single link topology +| | Run Keyword If | ${framesize} < ${1522} | Add No Multi Seg to all DUTs +| | Apply startup configuration on all VPP DUTs +| | L2 bridge domain initialized in a 3-node circular topology +| | Find PDR using binary search and pps +| | ... | ${framesize} | ${binary_min} | ${binary_max} | 3-node-bridge +| | ... | ${min_rate} | ${max_rate} | ${threshold} +| | ... | ${glob_loss_acceptance} | ${glob_loss_acceptance_type} + +*** Test Cases *** +| tc01-64B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | ${64} | ${100000} | 1 | 1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | [Tags] | 1T1C | STHREAD | NDRDISC +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc02-64B-1t1c-eth-l2bdbasemaclrn-pdrdisc +| | ... | ${64} | ${100000} | 1 | 1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps, LT=0.5%. +| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc03-1518B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | ${1518} | ${10000} | 1 | 1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Tags] | 1T1C | STHREAD | NDRDISC +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc04-1518B-1t1c-eth-l2bdbasemaclrn-pdrdisc +| | ... | ${1518} | ${10000} | 1 | 1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc05-9000B-1t1c-eth-l2bdbasemaclrn-ndrdisc +| | ... | ${9000} | ${10000} | 1 | 1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Tags] | 1T1C | STHREAD | NDRDISC +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc06-9000B-1t1c-eth-l2bdbasemaclrn-pdrdisc +| | ... | ${9000} | ${10000} | 1 | 1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1T1C | STHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc07-64B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | ${64} | ${100000} | 2 | 1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | [Tags] | 2T2C | MTHREAD | NDRDISC +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc08-64B-2t2c-eth-l2bdbasemaclrn-pdrdisc +| | ... | ${64} | ${100000} | 2 | 1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps, LT=0.5%. +| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc09-1518B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | ${1518} | ${10000} | 2 | 1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Tags] | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc10-1518B-2t2c-eth-l2bdbasemaclrn-pdrdisc +| | ... | ${1518} | ${10000} | 2 | 1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc11-9000B-2t2c-eth-l2bdbasemaclrn-ndrdisc +| | ... | ${9000} | ${10000} | 2 | 1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Tags] | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc12-9000B-2t2c-eth-l2bdbasemaclrn-pdrdisc +| | ... | ${9000} | ${10000} | 2 | 1 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Tags] | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc13-64B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | ${64} | ${100000} | 4 | 2 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps. +| | [Tags] | 4T4C | MTHREAD | NDRDISC +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc14-64B-4t4c-eth-l2bdbasemaclrn-pdrdisc +| | ... | ${64} | ${100000} | 4 | 2 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 100kpps, LT=0.5%. +| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc15-1518B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | ${1518} | ${10000} | 4 | 2 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc16-1518B-4t4c-eth-l2bdbasemaclrn-pdrdisc +| | ... | ${1518} | ${10000} | 4 | 2 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search + +| tc17-9000B-4t4c-eth-l2bdbasemaclrn-ndrdisc +| | ... | ${9000} | ${10000} | 4 | 2 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps. +| | [Tags] | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain NDR Binary Search + +| tc18-9000B-4t4c-eth-l2bdbasemaclrn-pdrdisc +| | ... | ${9000} | ${10000} | 4 | 2 +| | [Documentation] +| | ... | [Cfg] DUT runs L2BD switching config with with\ +| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port. +| | ... | [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE\ +| | ... | linerate, step 10kpps, LT=0.5%. +| | [Tags] | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH +| | [Template] | L2 Bridge Domain PDR Binary Search |