path: root/resources/libraries/robot/performance/performance_configuration.robot

# Copyright (c) 2018 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
#     http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.

*** Settings ***
| Library | Collections
| Library | String
| Library | resources.libraries.python.topology.Topology
| Library | resources.libraries.python.NodePath
| Library | resources.libraries.python.DpdkUtil
| Library | resources.libraries.python.InterfaceUtil
| Library | resources.libraries.python.VhostUser
| Library | resources.libraries.python.TrafficGenerator
| Library | resources.libraries.python.TrafficGenerator.TGDropRateSearchImpl
| Library | resources.libraries.python.Classify
| Library | resources.libraries.python.IPUtil
| Library | resources.libraries.python.L2Util
| Resource | resources/libraries/robot/shared/default.robot
| Resource | resources/libraries/robot/shared/interfaces.robot
| Resource | resources/libraries/robot/shared/counters.robot
| Resource | resources/libraries/robot/l2/l2_bridge_domain.robot
| Resource | resources/libraries/robot/l2/l2_xconnect.robot
| Resource | resources/libraries/robot/l2/l2_patch.robot
| Resource | resources/libraries/robot/ip/ip4.robot
| Resource | resources/libraries/robot/ip/ip6.robot
| Resource | resources/libraries/robot/vm/qemu.robot
| Resource | resources/libraries/robot/l2/tagging.robot
| Resource | resources/libraries/robot/overlay/srv6.robot
| Documentation | Performance suite keywords - configuration.

*** Keywords ***
| Set interfaces in path up
| | [Documentation]
| | ... | *Set UP state on VPP interfaces in path on all DUT nodes and set
| | ... | maximal MTU.*
| | ...
# TODO: Rework KW to set all interfaces in path UP and set MTU (including
# software interfaces. Run KW at the start phase of VPP setup to split
# from other "functional" configuration. This will allow modularity of this
# library
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | ${if1_status} | ${value}= | Run Keyword And Ignore Error
| | | ... | Variable Should Exist | ${${dut}_if1}
| | | Run Keyword If | '${if1_status}' == 'PASS'
| | | ... | Set Interface State | ${nodes['${dut}']} | ${${dut}_if1} | up
| | | ... | ELSE
| | | ... | Set Interface State | ${nodes['${dut}']} | ${${dut}_if1_1} | up
| | | Run Keyword Unless | '${if1_status}' == 'PASS'
| | | ... | Set Interface State | ${nodes['${dut}']} | ${${dut}_if1_2} | up
| | | ${if2_status} | ${value}= | Run Keyword And Ignore Error
| | | ... | Variable Should Exist | ${${dut}_if2}
| | | Run Keyword If | '${if2_status}' == 'PASS'
| | | ... | Set Interface State | ${nodes['${dut}']} | ${${dut}_if2} | up
| | | ... | ELSE
| | | ... | Set Interface State | ${nodes['${dut}']} | ${${dut}_if2_1} | up
| | | Run Keyword Unless | '${if2_status}' == 'PASS'
| | | ... | Set Interface State | ${nodes['${dut}']} | ${${dut}_if2_2} | up
| | All VPP Interfaces Ready Wait | ${nodes}
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | ${if1_status} | ${value}= | Run Keyword And Ignore Error
| | | ... | Variable Should Exist | ${${dut}_if1}
| | | Run Keyword If | '${if1_status}' == 'PASS'
| | | ... | VPP Set Interface MTU | ${nodes['${dut}']} | ${${dut}_if1}
| | | ... | ELSE
| | | ... | VPP Set Interface MTU | ${nodes['${dut}']} | ${${dut}_if1_1}
| | | Run Keyword Unless | '${if1_status}' == 'PASS'
| | | ... | VPP Set Interface MTU | ${nodes['${dut}']} | ${${dut}_if1_2}
| | | ${if2_status} | ${value}= | Run Keyword And Ignore Error
| | | ... | Variable Should Exist | ${${dut}_if2}
| | | Run Keyword If | '${if2_status}' == 'PASS'
| | | ... | VPP Set Interface MTU | ${nodes['${dut}']} | ${${dut}_if2}
| | | ... | ELSE
| | | ... | VPP Set Interface MTU | ${nodes['${dut}']} | ${${dut}_if2_1}
| | | Run Keyword Unless | '${if2_status}' == 'PASS'
| | | ... | VPP Set Interface MTU | ${nodes['${dut}']} | ${${dut}_if2_2}
| | All VPP Interfaces Ready Wait | ${nodes}

| Initialize AVF interfaces
| | [Documentation]
| | ... | Initialize AVF interfaces on each DUT. Interfaces are brought up.
| | ...
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | ${if1_pci}= | Get Interface PCI Addr | ${nodes['${dut}']}
| | | ... | ${${dut}_if1_vf0}
| | | ${if2_pci}= | Get Interface PCI Addr | ${nodes['${dut}']}
| | | ... | ${${dut}_if2_vf0}
| | | ${dut_eth_vf_if1}= | VPP Create AVF Interface | ${nodes['${dut}']}
| | | ... | ${if1_pci}
| | | ${dut_eth_vf_if2}= | VPP Create AVF Interface | ${nodes['${dut}']}
| | | ... | ${if2_pci}
| | | Set Test Variable | ${${dut}_if1} | ${dut_eth_vf_if1}
| | | Set Test Variable | ${${dut}_if2} | ${dut_eth_vf_if2}
| | Set interfaces in path up

| Initialize IPSec in 3-node circular topology
| | [Documentation]
| | ... | Set UP state on VPP interfaces in path on nodes in 3-node circular
| | ... | topology. Get the interface MAC addresses and setup ARP on all VPP
| | ... | interfaces. Setup IPv4 addresses with /24 prefix on DUT-TG and
| | ... | DUT1-DUT2 links. Set routing for encrypted traffic on both DUT nodes
| | ... | with prefix /8 and next hop of neighbour DUT or TG interface IPv4
| | ... | address.
| | ...
| | Set interfaces in path up
| | VPP Show Crypto Device Mapping | ${dut1}
| | VPP Show Crypto Device Mapping | ${dut2}
| | ${tg_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | ${dut1_if1_mac}= | Get Interface MAC | ${dut1} | ${dut1_if1}
| | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
| | ${dut2_if2_mac}= | Get Interface MAC | ${dut2} | ${dut2_if2}
| | Set Test Variable | ${tg_if1_mac}
| | Set Test Variable | ${tg_if2_mac}
| | Set Test Variable | ${dut1_if1_mac}
| | Set Test Variable | ${dut1_if2_mac}
| | Set Test Variable | ${dut2_if1_mac}
| | Set Test Variable | ${dut2_if2_mac}
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if1}
| | ... | ${dut1_if1_ip4} | 24
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2}
| | ... | ${dut1_if2_ip4} | 24
| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if1}
| | ... | ${dut2_if1_ip4} | 24
| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if2}
| | ... | ${dut2_if2_ip4} | 24
| | Add arp on dut | ${dut1} | ${dut1_if1} | ${tg_if1_ip4} | ${tg_if1_mac}
| | Add arp on dut | ${dut1} | ${dut1_if2} | ${dut2_if1_ip4} | ${dut2_if1_mac}
| | Add arp on dut | ${dut2} | ${dut2_if2} | ${tg_if2_ip4} | ${tg_if2_mac}
| | Add arp on dut | ${dut2} | ${dut2_if1} | ${dut1_if2_ip4} | ${dut1_if2_mac}
| | Vpp Route Add | ${dut1} | ${laddr_ip4} | 8 | ${tg_if1_ip4} | ${dut1_if1}
| | Vpp Route Add | ${dut2} | ${raddr_ip4} | 8 | ${tg_if2_ip4} | ${dut2_if2}

| Initialize IPv4 forwarding in circular topology
| | [Documentation]
| | ... | Set UP state on VPP interfaces in path on nodes in 2-node / 3-node
| | ... | circular topology. Get the interface MAC addresses and setup ARP on
| | ... | all VPP interfaces. Setup IPv4 addresses with /24 prefix on DUT-TG
| | ... | links. In case of 3-node topology setup IPv4 adresses with /30 prefix
| | ... | on DUT1-DUT2 link and set routing on both DUT nodes with prefix /24
| | ... | and next hop of neighbour DUT interface IPv4 address.
| | ...
| | ${dut2_status} | ${value}= | Run Keyword And Ignore Error
| | ... | Variable Should Exist | ${dut2}
| | ...
| | Set interfaces in path up
| | ...
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | ${dut1_if2_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Get Interface MAC | ${dut2} | ${dut2_if1}
| | ...
| | Add arp on dut | ${dut1} | ${dut1_if1} | 10.10.10.2 | ${tg1_if1_mac}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Add arp on dut | ${dut1} | ${dut1_if2} | 1.1.1.2 | ${dut2_if1_mac}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Add arp on dut | ${dut2} | ${dut2_if1} | 1.1.1.1 | ${dut1_if2_mac}
| | ${dut}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Set Variable | ${dut2}
| | ... | ELSE | Set Variable | ${dut1}
| | ${dut_if2}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Set Variable | ${dut2_if2}
| | ... | ELSE | Set Variable | ${dut1_if2}
| | Add arp on dut | ${dut} | ${dut_if2} | 20.20.20.2 | ${tg1_if2_mac}
| | ...
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if1}
| | ... | 10.10.10.1 | 24
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2}
| | ... | 1.1.1.1 | 30
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Configure IP addresses on interfaces | ${dut2} | ${dut2_if1}
| | ... | 1.1.1.2 | 30
| | Configure IP addresses on interfaces | ${dut} | ${dut_if2}
| | ... | 20.20.20.1 | 24
| | ...
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Vpp Route Add | ${dut1} | 20.20.20.0 | 24 | 1.1.1.2 | ${dut1_if2}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Vpp Route Add | ${dut2} | 10.10.10.0 | 24 | 1.1.1.1 | ${dut2_if1}

| Initialize IPv4 forwarding with scaling in circular topology
| | [Documentation]
| | ... | Custom setup of IPv4 topology with scalability of ip routes on all
| | ... | DUT nodes in 2-node / 3-node circular topology
| | ...
| | ... | *Arguments:*
| | ... | - ${count} - IP route count. Type: integer
| | ...
| | ... | *Return:*
| | ... | - No value returned
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize IPv4 forwarding with scaling in 3-node circular \
| | ... | topology \| 100000 \|
| | ...
| | [Arguments] | ${count}
| | ...
| | ${dut2_status} | ${value}= | Run Keyword And Ignore Error
| | ... | Variable Should Exist | ${dut2}
| | ...
| | Set interfaces in path up
| | ...
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | ${dut1_if2_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Get Interface MAC | ${dut2} | ${dut2_if1}
| | Add arp on dut | ${dut1} | ${dut1_if1} | 1.1.1.1 | ${tg1_if1_mac}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Add arp on dut | ${dut1} | ${dut1_if2} | 2.2.2.2 | ${dut2_if1_mac}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Add arp on dut | ${dut2} | ${dut2_if1} | 2.2.2.1 | ${dut1_if2_mac}
| | ${dut}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Set Variable | ${dut2}
| | ... | ELSE | Set Variable | ${dut1}
| | ${dut_if2}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Set Variable | ${dut2_if2}
| | ... | ELSE | Set Variable | ${dut1_if2}
| | Add arp on dut | ${dut} | ${dut_if2} | 3.3.3.1 | ${tg1_if2_mac}
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if1} | 1.1.1.2 | 30
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2} | 2.2.2.1 | 30
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Configure IP addresses on interfaces | ${dut2} | ${dut2_if1} | 2.2.2.2 | 30
| | Configure IP addresses on interfaces | ${dut} | ${dut_if2} | 3.3.3.2 | 30
| | Vpp Route Add | ${dut1} | 10.0.0.0 | 32 | 1.1.1.1 | ${dut1_if1}
| | ... | count=${count}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Vpp Route Add | ${dut1} | 20.0.0.0 | 32 | 2.2.2.2 | ${dut1_if2}
| | ... | count=${count}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Vpp Route Add | ${dut2} | 10.0.0.0 | 32 | 2.2.2.1 | ${dut2_if1}
| | ... | count=${count}
| | Vpp Route Add | ${dut} | 20.0.0.0 | 32 | 3.3.3.1 | ${dut_if2}
| | ... | count=${count}

| Initialize IPv4 forwarding with vhost in 2-node circular topology
| | [Documentation]
| | ... | Create pairs of Vhost-User interfaces for defined number of VMs on
| | ... | VPP node. Set UP state of all VPP interfaces in path. Create
| | ... | ${vm_count}+1 FIB tables on DUT with multipath routing. Assign each
| | ... | Virtual interface to FIB table with Physical interface or Virtual
| | ... | interface on both nodes. Setup IPv4 addresses with /30 prefix on
| | ... | DUT-TG links. Set routing on DUT nodes in all FIB tables with prefix
| | ... | /24 and next hop of neighbour IPv4 address. Setup ARP on all VPP
| | ... | interfaces.
| | ...
| | ... | *Arguments:*
| | ... | - vm_count - Number of guest VMs. Type: integer
| | ...
| | ... | *Note:*
| | ... | Socket paths for VM are defined in following format:
| | ... | - /tmp/sock-${VM_ID}-1
| | ... | - /tmp/sock-${VM_ID}-2
| | ...
| | ... | *Example:*
| | ...
| | ... | \| IPv4 forwarding with Vhost-User initialized in a 2-node circular\
| | ... | topology \| 1 \|
| | ...
| | [Arguments] | ${vm_count}=${1}
| | ...
| | Set interfaces in path up
| | ${fib_table_1}= | Set Variable | ${101}
| | ${fib_table_2}= | Evaluate | ${fib_table_1}+${vm_count}
| | Add Fib Table | ${dut1} | ${fib_table_1}
| | And Vpp Route Add | ${dut1} | 10.10.10.0 | 24 | vrf=${fib_table_1}
| | ... | gateway=1.1.1.2 | interface=${dut1_if1} | multipath=${TRUE}
| | Add Fib Table | ${dut1} | ${fib_table_2}
| | And Vpp Route Add | ${dut1} | 20.20.20.0 | 24 | vrf=${fib_table_2}
| | ... | gateway=2.2.2.2 | interface=${dut1_if2} | multipath=${TRUE}
| | Assign Interface To Fib Table | ${dut1} | ${dut1_if1} | ${fib_table_1}
| | Assign Interface To Fib Table | ${dut1} | ${dut1_if2} | ${fib_table_2}
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if1} | 1.1.1.2 | 30
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2} | 2.2.2.1 | 30
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | Add arp on dut | ${dut1} | ${dut1_if1} | 1.1.1.1 | ${tg1_if1_mac}
| | Add arp on dut | ${dut1} | ${dut1_if2} | 2.2.2.2 | ${tg1_if2_mac}
| | Vpp Route Add | ${dut1} | 10.10.10.0 | 24 | 1.1.1.1 | ${dut1_if1}
| | ... | vrf=${fib_table_1}
| | Vpp Route Add | ${dut1} | 20.20.20.0 | 24 | 2.2.2.2 | ${dut1_if2}
| | ... | vrf=${fib_table_2}
| | ${ip_base_start}= | Set Variable | ${4}
| | :FOR | ${number} | IN RANGE | 1 | ${vm_count}+1
| | | ${sock1}= | Set Variable | /tmp/sock-${number}-1
| | | ${sock2}= | Set Variable | /tmp/sock-${number}-2
| | | ${fib_table_1}= | Evaluate | ${100}+${number}
| | | ${fib_table_2}= | Evaluate | ${fib_table_1}+${1}
| | | ${ip_base_vif1}= | Evaluate | ${ip_base_start}+(${number}-1)*2
| | | ${ip_base_vif2}= | Evaluate | ${ip_base_vif1}+1
| | | ${ip_net_vif1}= | Set Variable
| | | ... | ${ip_base_vif1}.${ip_base_vif1}.${ip_base_vif1}
| | | ${ip_net_vif2}= | Set Variable
| | | ... | ${ip_base_vif2}.${ip_base_vif2}.${ip_base_vif2}
| | | Configure vhost interfaces for L2BD forwarding | ${dut1}
| | | ... | ${sock1} | ${sock2} | dut1-vhost-${number}-if1
| | | ... | dut1-vhost-${number}-if2
| | | Set Interface State | ${dut1} | ${dut1-vhost-${number}-if1} | up
| | | Set Interface State | ${dut1} | ${dut1-vhost-${number}-if2} | up
| | | Add Fib Table | ${dut1} | ${fib_table_1}
| | | And Vpp Route Add | ${dut1} | 20.20.20.0 | 24 | vrf=${fib_table_1}
| | | ... | gateway=${ip_net_vif1}.1 | interface=${dut1-vhost-${number}-if1}
| | | ... | multipath=${TRUE}
| | | Add Fib Table | ${dut1} | ${fib_table_2}
| | | And Vpp Route Add | ${dut1} | 10.10.10.0 | 24 | vrf=${fib_table_2}
| | | ... | gateway=${ip_net_vif2}.2 | interface=${dut1-vhost-${number}-if2}
| | | ... | multipath=${TRUE}
| | | Assign Interface To Fib Table | ${dut1} | ${dut1-vhost-${number}-if1}
| | | ... | ${fib_table_1}
| | | Assign Interface To Fib Table | ${dut1} | ${dut1-vhost-${number}-if2}
| | | ... | ${fib_table_2}
| | | Configure IP addresses on interfaces
| | | ... | ${dut1} | ${dut1-vhost-${number}-if1} | ${ip_net_vif1}.1 | 30
| | | ... | ${dut1} | ${dut1-vhost-${number}-if2} | ${ip_net_vif2}.1 | 30
| | | ${dut1_vif1_idx}= | Get Interface SW Index | ${dut1}
| | | ... | ${dut1-vhost-${number}-if1}
| | | ${dut1_vif2_idx}= | Get Interface SW Index | ${dut1}
| | | ... | ${dut1-vhost-${number}-if2}
| | | ${dut1_vif1_mac}= | Get Vhost User Mac By Sw Index | ${dut1}
| | | ... | ${dut1_vif1_idx}
| | | ${dut1_vif2_mac}= | Get Vhost User Mac By Sw Index | ${dut1}
| | | ... | ${dut1_vif2_idx}
| | | Set Test Variable | ${dut1-vhost-${number}-if1_mac}
| | | ... | ${dut1_vif1_mac}
| | | Set Test Variable | ${dut1-vhost-${number}-if2_mac}
| | | ... | ${dut1_vif2_mac}
| | | ${qemu_id}= | Set Variable If | ${number} < 10 | 0${number}
| | | ... | ${number}
| | | Add arp on dut | ${dut1} | ${dut1-vhost-${number}-if1}
| | | ... | ${ip_net_vif1}.2 | 52:54:00:00:${qemu_id}:01
| | | Add arp on dut | ${dut1} | ${dut1-vhost-${number}-if2}
| | | ... | ${ip_net_vif2}.2 | 52:54:00:00:${qemu_id}:02
| | | Vpp Route Add | ${dut1} | 20.20.20.0 | 24 | ${ip_net_vif1}.2
| | | ... | ${dut1-vhost-${number}-if1} | vrf=${fib_table_1}
| | | Vpp Route Add | ${dut1} | 10.10.10.0 | 24 | ${ip_net_vif2}.2
| | | ... | ${dut1-vhost-${number}-if2} | vrf=${fib_table_2}

| Initialize IPv4 forwarding with vhost in 3-node circular topology
| | [Documentation]
| | ... | Create pairs of Vhost-User interfaces for defined number of VMs on all
| | ... | VPP nodes. Set UP state of all VPP interfaces in path. Create
| | ... | ${vm_count}+1 FIB tables on each DUT with multipath routing. Assign
| | ... | each Virtual interface to FIB table with Physical interface or Virtual
| | ... | interface on both nodes. Setup IPv4 addresses with /30 prefix on
| | ... | DUT-TG links and /30 prefix on DUT1-DUT2 link. Set routing on all DUT
| | ... | nodes in all FIB tables with prefix /24 and next hop of neighbour IPv4
| | ... | address. Setup ARP on all VPP interfaces.
| | ...
| | ... | *Arguments:*
| | ... | - vm_count - Number of guest VMs. Type: integer
| | ...
| | ... | *Note:*
| | ... | Socket paths for VM are defined in following format:
| | ... | - /tmp/sock-${VM_ID}-1
| | ... | - /tmp/sock-${VM_ID}-2
| | ...
| | ... | *Example:*
| | ...
| | ... | \| IPv4 forwarding with Vhost-User initialized in a 3-node circular\
| | ... | topology \| 1 \|
| | ...
| | [Arguments] | ${vm_count}=${1}
| | ...
| | Set interfaces in path up
| | ${fib_table_1}= | Set Variable | ${101}
| | ${fib_table_2}= | Evaluate | ${fib_table_1}+${vm_count}
| | Add Fib Table | ${dut1} | ${fib_table_1}
| | And Vpp Route Add | ${dut1} | 10.10.10.0 | 24 | vrf=${fib_table_1}
| | ... | gateway=1.1.1.2 | interface=${dut1_if1} | multipath=${TRUE}
| | Add Fib Table | ${dut1} | ${fib_table_2}
| | And Vpp Route Add | ${dut1} | 20.20.20.0 | 24 | vrf=${fib_table_2}
| | ... | gateway=2.2.2.2 | interface=${dut1_if2} | multipath=${TRUE}
| | Add Fib Table | ${dut2} | ${fib_table_1}
| | And Vpp Route Add | ${dut2} | 10.10.10.0 | 24 | vrf=${fib_table_1}
| | ... | gateway=2.2.2.1 | interface=${dut2_if1} | multipath=${TRUE}
| | Add Fib Table | ${dut2} | ${fib_table_2}
| | And Vpp Route Add | ${dut2} | 20.20.20.0 | 24 | vrf=${fib_table_2}
| | ... | gateway=3.3.3.2 | interface=${dut2_if2} | multipath=${TRUE}
| | Assign Interface To Fib Table | ${dut1} | ${dut1_if1} | ${fib_table_1}
| | Assign Interface To Fib Table | ${dut1} | ${dut1_if2} | ${fib_table_2}
| | Assign Interface To Fib Table | ${dut2} | ${dut2_if1} | ${fib_table_1}
| | Assign Interface To Fib Table | ${dut2} | ${dut2_if2} | ${fib_table_2}
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if1} | 1.1.1.2 | 30
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2} | 2.2.2.1 | 30
| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if1} | 2.2.2.2 | 30
| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if2} | 3.3.3.1 | 30
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
| | Add arp on dut | ${dut1} | ${dut1_if1} | 1.1.1.1 | ${tg1_if1_mac}
| | Add arp on dut | ${dut1} | ${dut1_if2} | 2.2.2.2 | ${dut2_if1_mac}
| | Add arp on dut | ${dut2} | ${dut2_if1} | 2.2.2.1 | ${dut1_if2_mac}
| | Add arp on dut | ${dut2} | ${dut2_if2} | 3.3.3.2 | ${tg1_if2_mac}
| | Vpp Route Add | ${dut1} | 10.10.10.0 | 24 | 1.1.1.1 | ${dut1_if1}
| | ... | vrf=${fib_table_1}
| | Vpp Route Add | ${dut1} | 20.20.20.0 | 24 | 2.2.2.2 | ${dut1_if2}
| | ... | vrf=${fib_table_2}
| | Vpp Route Add | ${dut2} | 10.10.10.0 | 24 | 2.2.2.1 | ${dut2_if1}
| | ... | vrf=${fib_table_1}
| | Vpp Route Add | ${dut2} | 20.20.20.0 | 24 | 3.3.3.2 | ${dut2_if2}
| | ... | vrf=${fib_table_2}
| | ${ip_base_start}= | Set Variable | ${4}
| | :FOR | ${number} | IN RANGE | 1 | ${vm_count}+1
| | | ${sock1}= | Set Variable | /tmp/sock-${number}-1
| | | ${sock2}= | Set Variable | /tmp/sock-${number}-2
| | | ${fib_table_1}= | Evaluate | ${100}+${number}
| | | ${fib_table_2}= | Evaluate | ${fib_table_1}+${1}
| | | ${ip_base_vif1}= | Evaluate | ${ip_base_start}+(${number}-1)*2
| | | ${ip_base_vif2}= | Evaluate | ${ip_base_vif1}+1
| | | ${ip_net_vif1}= | Set Variable
| | | ... | ${ip_base_vif1}.${ip_base_vif1}.${ip_base_vif1}
| | | ${ip_net_vif2}= | Set Variable
| | | ... | ${ip_base_vif2}.${ip_base_vif2}.${ip_base_vif2}
| | | Configure vhost interfaces for L2BD forwarding | ${dut1}
| | | ... | ${sock1} | ${sock2} | dut1-vhost-${number}-if1
| | | ... | dut1-vhost-${number}-if2
| | | Set Interface State | ${dut1} | ${dut1-vhost-${number}-if1} | up
| | | Set Interface State | ${dut1} | ${dut1-vhost-${number}-if2} | up
| | | Configure vhost interfaces for L2BD forwarding | ${dut2}
| | | ... | ${sock1} | ${sock2} | dut2-vhost-${number}-if1
| | | ... | dut2-vhost-${number}-if2
| | | Set Interface State | ${dut2} | ${dut2-vhost-${number}-if1} | up
| | | Set Interface State | ${dut2} | ${dut2-vhost-${number}-if2} | up
| | | Add Fib Table | ${dut1} | ${fib_table_1}
| | | And Vpp Route Add | ${dut1} | 20.20.20.0 | 24 | vrf=${fib_table_1}
| | | ... | gateway=${ip_net_vif1}.1 | interface=${dut1-vhost-${number}-if1}
| | | ... | multipath=${TRUE}
| | | Add Fib Table | ${dut1} | ${fib_table_2}
| | | And Vpp Route Add | ${dut1} | 10.10.10.0 | 24 | vrf=${fib_table_2}
| | | ... | gateway=${ip_net_vif2}.2 | interface=${dut1-vhost-${number}-if2}
| | | ... | multipath=${TRUE}
| | | Add Fib Table | ${dut2} | ${fib_table_1}
| | | And Vpp Route Add | ${dut2} | 20.20.20.0 | 24 | vrf=${fib_table_1}
| | | ... | gateway=${ip_net_vif1}.1 | interface=${dut2-vhost-${number}-if1}
| | | ... | multipath=${TRUE}
| | | Add Fib Table | ${dut2} | ${fib_table_2}
| | | And Vpp Route Add | ${dut2} | 10.10.10.0 | 24 | vrf=${fib_table_2}
| | | ... | gateway=${ip_net_vif2}.2 | interface=${dut2-vhost-${number}-if2}
| | | ... | multipath=${TRUE}
| | | Assign Interface To Fib Table | ${dut1} | ${dut1-vhost-${number}-if1}
| | | ... | ${fib_table_1}
| | | Assign Interface To Fib Table | ${dut1} | ${dut1-vhost-${number}-if2}
| | | ... | ${fib_table_2}
| | | Assign Interface To Fib Table | ${dut2} | ${dut2-vhost-${number}-if1}
| | | ... | ${fib_table_1}
| | | Assign Interface To Fib Table | ${dut2} | ${dut2-vhost-${number}-if2}
| | | ... | ${fib_table_2}
| | | Configure IP addresses on interfaces
| | | ... | ${dut1} | ${dut1-vhost-${number}-if1} | ${ip_net_vif1}.1 | 30
| | | ... | ${dut1} | ${dut1-vhost-${number}-if2} | ${ip_net_vif2}.1 | 30
| | | ... | ${dut2} | ${dut2-vhost-${number}-if1} | ${ip_net_vif1}.1 | 30
| | | ... | ${dut2} | ${dut2-vhost-${number}-if2} | ${ip_net_vif2}.1 | 30
| | | ${dut1_vif1_idx}= | Get Interface SW Index | ${dut1}
| | | ... | ${dut1-vhost-${number}-if1}
| | | ${dut1_vif2_idx}= | Get Interface SW Index | ${dut1}
| | | ... | ${dut1-vhost-${number}-if2}
| | | ${dut2_vif1_idx}= | Get Interface SW Index | ${dut2}
| | | ... | ${dut2-vhost-${number}-if1}
| | | ${dut2_vif2_idx}= | Get Interface SW Index | ${dut2}
| | | ... | ${dut2-vhost-${number}-if2}
| | | ${dut1_vif1_mac}= | Get Vhost User Mac By Sw Index | ${dut1}
| | | ... | ${dut1_vif1_idx}
| | | ${dut1_vif2_mac}= | Get Vhost User Mac By Sw Index | ${dut1}
| | | ... | ${dut1_vif2_idx}
| | | ${dut2_vif1_mac}= | Get Vhost User Mac By Sw Index | ${dut2}
| | | ... | ${dut2_vif1_idx}
| | | ${dut2_vif2_mac}= | Get Vhost User Mac By Sw Index | ${dut2}
| | | ... | ${dut2_vif2_idx}
| | | Set Test Variable | ${dut1-vhost-${number}-if1_mac}
| | | ... | ${dut1_vif1_mac}
| | | Set Test Variable | ${dut1-vhost-${number}-if2_mac}
| | | ... | ${dut1_vif2_mac}
| | | Set Test Variable | ${dut2-vhost-${number}-if1_mac}
| | | ... | ${dut2_vif1_mac}
| | | Set Test Variable | ${dut2-vhost-${number}-if2_mac}
| | | ... | ${dut2_vif2_mac}
| | | ${qemu_id}= | Set Variable If | ${number} < 10 | 0${number}
| | | ... | ${number}
| | | Add arp on dut | ${dut1} | ${dut1-vhost-${number}-if1}
| | | ... | ${ip_net_vif1}.2 | 52:54:00:00:${qemu_id}:01
| | | Add arp on dut | ${dut1} | ${dut1-vhost-${number}-if2}
| | | ... | ${ip_net_vif2}.2 | 52:54:00:00:${qemu_id}:02
| | | Add arp on dut | ${dut2} | ${dut2-vhost-${number}-if1}
| | | ... | ${ip_net_vif1}.2 | 52:54:00:00:${qemu_id}:01
| | | Add arp on dut | ${dut2} | ${dut2-vhost-${number}-if2}
| | | ... | ${ip_net_vif2}.2 | 52:54:00:00:${qemu_id}:02
| | | Vpp Route Add | ${dut1} | 20.20.20.0 | 24 | ${ip_net_vif1}.2
| | | ... | ${dut1-vhost-${number}-if1} | vrf=${fib_table_1}
| | | Vpp Route Add | ${dut1} | 10.10.10.0 | 24 | ${ip_net_vif2}.2
| | | ... | ${dut1-vhost-${number}-if2} | vrf=${fib_table_2}
| | | Vpp Route Add | ${dut2} | 20.20.20.0 | 24 | ${ip_net_vif1}.2
| | | ... | ${dut2-vhost-${number}-if1} | vrf=${fib_table_1}
| | | Vpp Route Add | ${dut2} | 10.10.10.0 | 24 | ${ip_net_vif2}.2
| | | ... | ${dut2-vhost-${number}-if2} | vrf=${fib_table_2}

| Initialize IPv4 policer 2r3c-${t} in circular topology
| | [Documentation]
| | ... | Setup of 2r3c color-aware or color-blind policer with dst ip match
| | ... | on all DUT nodes in 2-node / 3-node circular topology. Policer is
| | ... | applied on links TG - DUTx.
| | ...
| | ${dscp}= | DSCP AF22
| | Policer Set Name | policer1
| | Policer Set CIR | ${cir}
| | Policer Set EIR | ${eir}
| | Policer Set CB | ${cb}
| | Policer Set EB | ${eb}
| | Policer Set Rate Type pps
| | Policer Set Round Type Closest
| | Policer Set Type 2R3C 2698
| | Policer Set Conform Action Transmit
| | Policer Set Exceed Action Mark and Transmit | ${dscp}
| | Policer Set Violate Action Transmit
| | Policer Enable Color Aware
| | Run Keyword If | ${t} == 'ca' | Policer Enable Color Aware
| | Policer Classify Set Precolor Exceed
| | Policer Set Node | ${dut1}
| | Policer Classify Set Interface | ${dut1_if1}
| | Policer Classify Set Match IP | 20.20.20.2 | ${False}
| | Policer Set Configuration
| | ${dut2_status} | ${value}= | Run Keyword And Ignore Error
| | ... | Variable Should Exist | ${dut2}
| | ${dut}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Set Variable | ${dut2}
| | ... | ELSE | Set Variable | ${dut1}
| | ${dut_if2}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Set Variable | ${dut2_if2}
| | ... | ELSE | Set Variable | ${dut1_if2}
| | Run Keyword Unless | '${dut2_status}' == 'PASS'
| | ... | Policer Set Name | policer2
| | Policer Set Node | ${dut}
| | Policer Classify Set Interface | ${dut_if2}
| | Policer Classify Set Match IP | 10.10.10.2 | ${False}
| | Policer Set Configuration

| Initialize IPv6 forwarding in 2-node circular topology
| | [Documentation]
| | ... | Set UP state on VPP interfaces in path on nodes in 2-node circular
| | ... | topology. Get the interface MAC addresses and setup neighbour on all
| | ... | VPP interfaces. Setup IPv6 addresses with /128 prefixes on all
| | ... | interfaces.
| | ...
| | Set interfaces in path up
| | ${prefix}= | Set Variable | 64
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if1} | 2001:1::1 | ${prefix}
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if2} | 2001:2::1 | ${prefix}
| | Suppress ICMPv6 router advertisement message | ${nodes}
| | Add Ip Neighbor | ${dut1} | ${dut1_if1} | 2001:1::2 | ${tg1_if1_mac}
| | Add Ip Neighbor | ${dut1} | ${dut1_if2} | 2001:2::2 | ${tg1_if2_mac}

| Initialize IPv6 forwarding in 3-node circular topology
| | [Documentation]
| | ... | Set UP state on VPP interfaces in path on nodes in 3-node circular
| | ... | topology. Get the interface MAC addresses and setup neighbour on all
| | ... | VPP interfaces. Setup IPv6 addresses with /128 prefixes on all
| | ... | interfaces. Set routing on both DUT nodes with prefix /64 and
| | ... | next hop of neighbour DUT interface IPv6 address.
| | ...
| | Set interfaces in path up
| | ${prefix}= | Set Variable | 64
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if1} | 2001:1::1 | ${prefix}
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if2} | 2001:3::1 | ${prefix}
| | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if1} | 2001:3::2 | ${prefix}
| | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if2} | 2001:2::1 | ${prefix}
| | Suppress ICMPv6 router advertisement message | ${nodes}
| | Add Ip Neighbor | ${dut1} | ${dut1_if1} | 2001:1::2 | ${tg1_if1_mac}
| | Add Ip Neighbor | ${dut2} | ${dut2_if2} | 2001:2::2 | ${tg1_if2_mac}
| | Add Ip Neighbor | ${dut1} | ${dut1_if2} | 2001:3::2 | ${dut2_if1_mac}
| | Add Ip Neighbor | ${dut2} | ${dut2_if1} | 2001:3::1 | ${dut1_if2_mac}
| | Vpp Route Add | ${dut1} | 2001:2::0 | ${prefix} | 2001:3::2 | ${dut1_if2}
| | Vpp Route Add | ${dut2} | 2001:1::0 | ${prefix} | 2001:3::1 | ${dut2_if1}

| Initialize IPv6 forwarding with scaling in circular topology
| | [Documentation]
| | ... | Custom setup of IPv6 topology with scalability of ip routes on all
| | ... | DUT nodes in 2-node / 3-node circular topology
| | ...
| | ... | *Arguments:*
| | ... | - ${count} - IP route count. Type: integer
| | ...
| | ... | *Return:*
| | ... | - No value returned
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize IPv6 forwarding with scaling in circular \
| | ... | topology \| 100000 \|
| | ...
| | [Arguments] | ${count}
| | ...
| | ${dut2_status} | ${value}= | Run Keyword And Ignore Error
| | ... | Variable Should Exist | ${dut2}
| | ...
| | Set interfaces in path up
| | ...
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | ${dut1_if2_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Get Interface MAC | ${dut2} | ${dut2_if1}
| | ${prefix}= | Set Variable | 64
| | ${host_prefix}= | Set Variable | 128
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if1} | 2001:3::1 | ${prefix}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if2} | 2001:4::1 | ${prefix}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if1} | 2001:4::2 | ${prefix}
| | ${dut}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Set Variable | ${dut2}
| | ... | ELSE | Set Variable | ${dut1}
| | ${dut_if2}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Set Variable | ${dut2_if2}
| | ... | ELSE | Set Variable | ${dut1_if2}
| | VPP Set If IPv6 Addr | ${dut} | ${dut_if2} | 2001:5::1 | ${prefix}
| | Suppress ICMPv6 router advertisement message | ${nodes}
| | Add Ip Neighbor | ${dut1} | ${dut1_if1} | 2001:3::2 | ${tg1_if1_mac}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Add Ip Neighbor | ${dut1} | ${dut1_if2} | 2001:4::2 | ${dut2_if1_mac}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Add Ip Neighbor | ${dut2} | ${dut2_if1} | 2001:4::1 | ${dut1_if2_mac}
| | Add Ip Neighbor | ${dut} | ${dut_if2} | 2001:5::2 | ${tg1_if2_mac}
| | Vpp Route Add | ${dut1} | 2001:1::0 | ${host_prefix} | 2001:3::2
| | ... | interface=${dut1_if1} | count=${count}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Vpp Route Add | ${dut1} | 2001:2::0 | ${host_prefix} | 2001:4::2
| | ... | interface=${dut1_if2} | count=${count}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Vpp Route Add | ${dut2} | 2001:1::0 | ${host_prefix} | 2001:4::1
| | ... | interface=${dut2_if1} | count=${count}
| | Vpp Route Add | ${dut} | 2001:2::0 | ${host_prefix} | 2001:5::2
| | ... | interface=${dut_if2} | count=${count}

| Initialize IPv6 iAcl whitelist in 3-node circular topology
| | [Documentation]
| | ... | Creates classify L3 table on DUTs. IPv6 iAcl security whitelist
| | ... | ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG.
| | ...
| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
| | ... | ${dut1} | ip6 | dst
| | And Vpp Configures Classify Session L3
| | ... | ${dut1} | permit | ${table_idx} | ${skip_n} | ${match_n}
| | ... | ip6 | dst | 2001:2::2
| | And Vpp Enable Input Acl Interface
| | ... | ${dut1} | ${dut1_if1} | ip6 | ${table_idx}
| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
| | ... | ${dut2} | ip6 | dst
| | And Vpp Configures Classify Session L3
| | ... | ${dut2} | permit | ${table_idx} | ${skip_n} | ${match_n}
| | ... | ip6 | dst | 2001:1::2
| | And Vpp Enable Input Acl Interface
| | ... | ${dut2} | ${dut2_if2} | ip6 | ${table_idx}

| Initialize IPv6 forwarding over SRv6 with encapsulation with '${n}' x SID '${prepos}' decapsulation in 3-node circular topology
| | [Documentation]
| | ... | Set UP state on VPP interfaces in path on nodes in 3-node circular
| | ... | topology. Get the interface MAC addresses and setup neighbours on all
| | ... | VPP interfaces. Setup IPv6 addresses on all interfaces. Set segment
| | ... | routing for IPv6 for required number of SIDs and configure IPv6 routes
| | ... | on both DUT nodes.
| | ...
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if1} | ${dut1_if1_ip6} | ${prefix}
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if2} | ${dut1_if2_ip6} | ${prefix}
| | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if1} | ${dut2_if1_ip6} | ${prefix}
| | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if2} | ${dut2_if2_ip6} | ${prefix}
| | Suppress ICMPv6 router advertisement message | ${nodes}
| | :FOR | ${number} | IN RANGE | 2 | ${dst_addr_nr}+2
| | | ${hexa_nr}= | Convert To Hex | ${number}
| | | Add Ip Neighbor | ${dut1} | ${dut1_if1} | ${tg_if1_ip6_subnet}${hexa_nr}
| | | ... | ${tg1_if1_mac}
| | | Add Ip Neighbor | ${dut2} | ${dut2_if2} | ${tg_if2_ip6_subnet}${hexa_nr}
| | | ... | ${tg1_if2_mac}
| | Add Ip Neighbor | ${dut1} | ${dut1_if2} | ${dut2_if1_ip6} | ${dut2_if1_mac}
| | Add Ip Neighbor | ${dut2} | ${dut2_if1} | ${dut1_if2_ip6} | ${dut1_if2_mac}
| | ${sid1}= | Set Variable If
| | ... | "${n}" == "1" | ${dut2_sid1}
| | ... | "${n}" == "2" | ${dut2_sid1_1}
| | ${sid2}= | Set Variable If
| | ... | "${n}" == "1" | ${dut1_sid2}
| | ... | "${n}" == "2" | ${dut1_sid2_1}
| | Vpp Route Add | ${dut1} | ${sid1} | ${sid_prefix} | ${dut2_if1_ip6}
| | ... | ${dut1_if2}
| | Vpp Route Add | ${dut2} | ${sid2} | ${sid_prefix} | ${dut1_if2_ip6}
| | ... | ${dut2_if1}
# Configure SRv6 for direction0
| | Set SR Encaps Source Address on DUT | ${dut1} | ${dut1_sid1}
| | @{sid_list_dir0}= | Run Keyword If | "${n}" == "1"
| | ... | Create List | ${dut2_sid1}
| | ... | ELSE IF | "${n}" == "2"
| | ... | Create List | ${dut2_sid1_1} | ${dut2_sid1_2}
| | Configure SR Policy on DUT | ${dut1} | ${dut1_bsid} | encap
| | ... | @{sid_list_dir0}
| | Configure SR Steer on DUT | ${dut1} | L3 | ${dut1_bsid}
| | ... | ip_addr=${tg_if2_ip6_subnet} | prefix=${sid_prefix}
| | Run Keyword If | "${n}" == "1"
| | ... | Configure SR LocalSID on DUT | ${dut2} | ${dut2_sid1} | end.dx6
| | ... | interface=${dut2_if2} | next_hop=${tg_if2_ip6_subnet}2
| | Run Keyword If | "${n}" == "2"
| | ... | Configure SR LocalSID on DUT | ${dut2} | ${dut2_sid1_1} | end
| | Run Keyword If | "${n}" == "2" and "${prepos}" != "without"
| | ... | Configure SR LocalSID on DUT | ${dut2} | ${dut2_sid1_2} | end.dx6
| | ... | interface=${dut2_if2} | next_hop=${tg_if2_ip6_subnet}2
| | Run Keyword If | "${n}" == "2" and "${prepos}" == "without"
| | ... | Vpp Route Add | ${dut2} | ${dut2_sid1_2} | ${sid_prefix}
| | ... | ${tg_if2_ip6_subnet}2 | ${dut2_if2}
# Configure SRv6 for direction1
| | Set SR Encaps Source Address on DUT | ${dut2} | ${dut2_sid2}
| | @{sid_list_dir1}= | Run Keyword If | "${n}" == "1"
| | ... | Create List | ${dut1_sid2}
| | ... | ELSE IF | "${n}" == "2"
| | ... | Create List | ${dut1_sid2_1} | ${dut1_sid2_2}
| | Configure SR Policy on DUT | ${dut2} | ${dut2_bsid} | encap
| | ... | @{sid_list_dir1}
| | Configure SR Steer on DUT | ${dut2} | L3 | ${dut2_bsid}
| | ... | ip_addr=${tg_if1_ip6_subnet} | prefix=${sid_prefix}
| | Run Keyword If | "${n}" == "1"
| | ... | Configure SR LocalSID on DUT | ${dut1} | ${dut1_sid2} | end.dx6
| | ... | interface=${dut1_if1} | next_hop=${tg_if1_ip6_subnet}2
| | Run Keyword If | "${n}" == "2"
| | ... | Configure SR LocalSID on DUT | ${dut1} | ${dut1_sid2_1} | end
| | Run Keyword If | "${n}" == "2" and "${prepos}" != "without"
| | ... | Configure SR LocalSID on DUT | ${dut1} | ${dut1_sid2_2} | end.dx6
| | ... | interface=${dut1_if1} | next_hop=${tg_if1_ip6_subnet}2
| | Run Keyword If | "${n}" == "2" and "${prepos}" == "without"
| | ... | Vpp Route Add | ${dut1} | ${dut1_sid2_2} | ${sid_prefix}
| | ... | ${tg_if1_ip6_subnet}2 | ${dut1_if1}
| | Set interfaces in path up

| Initialize IPv6 forwarding over SRv6 with endpoint to SR-unaware Service Function via '${behavior}' behaviour in 3-node circular topology
| | [Documentation]
| | ... | Create pair of Memif interfaces on all defined VPP nodes. Set UP
| | ... | state on VPP interfaces in path on nodes in 3-node circular topology.
| | ... | Get the interface MAC addresses and setup neighbours on all VPP
| | ... | interfaces. Setup IPv6 addresses on all interfaces. Set segment
| | ... | routing for IPv6 with defined behaviour function and configure IPv6
| | ... | routes on both DUT nodes.
| | ...
| | ... | *Note:*
| | ... | KW uses test variable ${rxq_count_int} set by KW Add worker threads
| | ... | and rxqueues to all DUTs
| | ...
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
| | ${sock1}= | Set Variable | memif-DUT1_VNF
| | ${sock2}= | Set Variable | memif-DUT2_VNF
| | Set up memif interfaces on DUT node | ${dut1} | ${sock1} | ${sock1}
| | ... | ${1} | dut1-memif-1-if1 | dut1-memif-1-if2 | ${rxq_count_int}
| | ... | ${rxq_count_int}
| | VPP Set interface MTU | ${dut1} | ${dut1-memif-1-if1}
| | VPP Set interface MTU | ${dut1} | ${dut1-memif-1-if2}
| | Set up memif interfaces on DUT node | ${dut2} | ${sock2} | ${sock2}
| | ... | ${1} | dut2-memif-1-if1 | dut2-memif-1-if2 | ${rxq_count_int}
| | ... | ${rxq_count_int}
| | VPP Set interface MTU | ${dut2} | ${dut2-memif-1-if1}
| | VPP Set interface MTU | ${dut2} | ${dut2-memif-1-if2}
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | Show Memif | ${nodes['${dut}']}
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if1} | ${dut1_if1_ip6} | ${prefix}
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if2} | ${dut1_if2_ip6} | ${prefix}
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1-memif-1-if1}
| | ... | ${dut1-memif-1-if1_ip6} | ${prefix}
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1-memif-1-if2}
| | ... | ${dut1-memif-1-if2_ip6} | ${prefix}
| | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if1} | ${dut2_if1_ip6} | ${prefix}
| | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if2} | ${dut2_if2_ip6} | ${prefix}
| | VPP Set If IPv6 Addr | ${dut2} | ${dut2-memif-1-if1}
| | ... | ${dut2-memif-1-if1_ip6} | ${prefix}
| | VPP Set If IPv6 Addr | ${dut2} | ${dut2-memif-1-if2}
| | ... | ${dut2-memif-1-if2_ip6} | ${prefix}
| | Suppress ICMPv6 router advertisement message | ${nodes}
| | Add Ip Neighbor | ${dut1} | ${dut1_if2} | ${dut2_if1_ip6} | ${dut2_if1_mac}
| | Add Ip Neighbor | ${dut2} | ${dut2_if1} | ${dut1_if2_ip6} | ${dut1_if2_mac}
| | Add Ip Neighbor | ${dut1} | ${dut1_if1} | ${tg_if1_ip6_subnet}2
| | ... | ${tg1_if1_mac}
| | Add Ip Neighbor | ${dut2} | ${dut2_if2} | ${tg_if2_ip6_subnet}2
| | ... | ${tg1_if2_mac}
| | ${dut1-memif-1-if2_mac}= | Get Interface MAC | ${dut1} | memif2
| | ${dut2-memif-1-if2_mac}= | Get Interface MAC | ${dut2} | memif2
| | Add Ip Neighbor | ${dut1} | ${dut1-memif-1-if1} | ${dut1_nh}
| | ... | ${dut1-memif-1-if2_mac}
| | Add Ip Neighbor | ${dut2} | ${dut2-memif-1-if1} | ${dut2_nh}
| | ... | ${dut2-memif-1-if2_mac}
| | Vpp Route Add | ${dut1} | ${dut2_sid1} | ${sid_prefix} | ${dut2_if1_ip6}
| | ... | ${dut1_if2}
| | Vpp Route Add | ${dut1} | ${out_sid2_1} | ${sid_prefix}
| | ... | ${tg_if1_ip6_subnet}2 | ${dut1_if1}
| | Vpp Route Add | ${dut2} | ${dut1_sid2} | ${sid_prefix} | ${dut1_if2_ip6}
| | ... | ${dut2_if1}
| | Vpp Route Add | ${dut2} | ${out_sid1_1} | ${sid_prefix}
| | ... | ${tg_if2_ip6_subnet}2 | ${dut2_if2}
# Configure SRv6 for direction0 on DUT1
| | Set SR Encaps Source Address on DUT | ${dut1} | ${dut1_sid1}
| | @{sid_list_dir0}= | Create List | ${dut2_sid1} | ${out_sid1_1}
| | ... | ${out_sid1_2}
| | Configure SR Policy on DUT | ${dut1} | ${dut1_bsid} | encap
| | ... | @{sid_list_dir0}
| | Configure SR Steer on DUT | ${dut1} | L3 | ${dut1_bsid}
| | ... | ip_addr=${tg_if2_ip6_subnet} | prefix=${sid_prefix}
# Configure SRv6 for direction1 on DUT2
| | Set SR Encaps Source Address on DUT | ${dut2} | ${dut2_sid2}
| | @{sid_list_dir1}= | Create List | ${dut1_sid2} | ${out_sid2_1}
| | ... | ${out_sid2_2}
| | Configure SR Policy on DUT | ${dut2} | ${dut2_bsid} | encap
| | ... | @{sid_list_dir1}
| | Configure SR Steer on DUT | ${dut2} | L3 | ${dut2_bsid}
| | ... | ip_addr=${tg_if1_ip6_subnet} | prefix=${sid_prefix}
# Configure SRv6 for direction0 on DUT2
| | ${dut2_out_if}= | Get Interface Name | ${dut2} | memif1
| | ${dut2_in_if}= | Get Interface Name | ${dut2} | memif2
| | Remove Values From List | ${sid_list_dir0} | ${dut2_sid1}
| | Run Keyword If | "${behavior}" == "static_proxy"
| | ... | Configure SR LocalSID on DUT | ${dut2} | ${dut2_sid1} | end.as
| | ... | ${NONE} | ${dut2_nh} | ${NONE} | ${dut2_out_if} | ${dut2_in_if}
| | ... | ${dut1_sid1} | @{sid_list_dir0}
| | ... | ELSE IF | "${behavior}" == "dynamic_proxy"
| | ... | Configure SR LocalSID on DUT | ${dut2} | ${dut2_sid1} | end.ad
| | ... | next_hop=${dut2_nh} | out_if=${dut2_out_if} | in_if=${dut2_in_if}
| | ... | ELSE IF | "${behavior}" == "masquerading"
| | ... | Configure SR LocalSID on DUT | ${dut2} | ${dut2_sid1} | end.am
| | ... | next_hop=${dut2_nh} | out_if=${dut2_out_if} | in_if=${dut2_in_if}
| | ... | ELSE | Fail | Unsupported behaviour: ${behavior}
# Configure SRv6 for direction1 on DUT1
| | ${dut1_out_if}= | Get Interface Name | ${dut1} | memif1
| | ${dut1_in_if}= | Get Interface Name | ${dut1} | memif2
| | Remove Values From List | ${sid_list_dir1} | ${dut1_sid2}
| | Run Keyword If | "${behavior}" == "static_proxy"
| | ... | Configure SR LocalSID on DUT | ${dut1} | ${dut1_sid2} | end.as
| | ... | ${NONE} | ${dut1_nh} | ${NONE} | ${dut1_out_if} | ${dut1_in_if}
| | ... | ${dut2_sid2} | @{sid_list_dir1}
| | ... | ELSE IF | "${behavior}" == "dynamic_proxy"
| | ... | Configure SR LocalSID on DUT | ${dut1} | ${dut1_sid2} | end.ad
| | ... | next_hop=${dut1_nh} | out_if=${dut1_out_if} | in_if=${dut1_in_if}
| | ... | ELSE IF | "${behavior}" == "masquerading"
| | ... | Configure SR LocalSID on DUT | ${dut1} | ${dut1_sid2} | end.am
| | ... | next_hop=${dut1_nh} | out_if=${dut1_out_if} | in_if=${dut1_in_if}
| | ... | ELSE | Fail | Unsupported behaviour: ${behavior}
| | Set interfaces in path up

| Initialize L2 patch
| | [Documentation]
| | ... | Setup L2 patch topology by cross connecting two interfaces on
| | ... | each DUT. Interfaces are brought up.
| | ...
| | Set interfaces in path up
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | Configure L2patch | ${nodes['${dut}']} | ${${dut}_if1} | ${${dut}_if2}

| Initialize L2 xconnect in 2-node circular topology
| | [Documentation]
| | ... | Setup L2 xconnect topology by cross connecting two interfaces on
| | ... | each DUT. Interfaces are brought up.
| | ...
| | Set interfaces in path up
| | Configure L2XC | ${dut1} | ${dut1_if1} | ${dut1_if2}

| Initialize L2 xconnect in 3-node circular topology
| | [Documentation]
| | ... | Setup L2 xconnect topology by cross connecting two interfaces on
| | ... | each DUT. Interfaces are brought up.
| | ... |
| | Set interfaces in path up
| | Configure L2XC | ${dut1} | ${dut1_if1} | ${dut1_if2}
| | Configure L2XC | ${dut2} | ${dut2_if1} | ${dut2_if2}

| Initialize L2 xconnect with VXLANoIPv4 in 3-node circular topology
| | [Documentation]
| | ... | Setup L2 xconnect topology with VXLANoIPv4 by cross connecting
| | ... | physical and vxlan interfaces on each DUT. All interfaces are brought
| | ... | up. IPv4 addresses with prefix /24 are configured on interfaces
| | ... | between DUTs. VXLAN sub-interfaces has same IPv4 address as
| | ... | interfaces.
| | ...
| | Set interfaces in path up
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2} | 172.16.0.1 | 24
| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if1} | 172.16.0.2 | 24
| | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
| | Add arp on dut | ${dut1} | ${dut1_if2} | 172.16.0.2 | ${dut2_if1_mac}
| | Add arp on dut | ${dut2} | ${dut2_if1} | 172.16.0.1 | ${dut1_if2_mac}
| | ${dut1s_vxlan}= | Create VXLAN interface | ${dut1} | 24
| | ... | 172.16.0.1 | 172.16.0.2
| | Configure L2XC | ${dut1} | ${dut1_if1} | ${dut1s_vxlan}
| | ${dut2s_vxlan}= | Create VXLAN interface | ${dut2} | 24
| | ... | 172.16.0.2 | 172.16.0.1
| | Configure L2XC | ${dut2} | ${dut2_if2} | ${dut2s_vxlan}

| Initialize L2 xconnect with Vhost-User on node
| | [Documentation]
| | ... | Create pairs of Vhost-User interfaces for defined number of VMs on
| | ... | defined VPP node. Add each Vhost-User interface into L2 cross-connect
| | ... | with with physical inteface or Vhost-User interface of another VM.
| | ...
| | ... | *Arguments:*
| | ... | - dut - DUT node. Type: string
| | ... | - vm_count - VM count. Type: integer
| | ...
| | ... | *Note:*
| | ... | Socket paths for VM are defined in following format:
| | ... | - /tmp/sock-${VM_ID}-1
| | ... | - /tmp/sock-${VM_ID}-2
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 xconnect with Vhost-User on node \| DUT1 \| 1 \|
| | ...
| | [Arguments] | ${dut} | ${vm_count}=${1}
| | ...
| | :FOR | ${number} | IN RANGE | 1 | ${vm_count}+1
| | | ${sock1}= | Set Variable | /tmp/sock-${number}-1
| | | ${sock2}= | Set Variable | /tmp/sock-${number}-2
| | | ${prev_index}= | Evaluate | ${number}-1
| | | Configure vhost interfaces for L2BD forwarding | ${nodes['${dut}']}
| | | ... | ${sock1} | ${sock2} | ${dut}-vhost-${number}-if1
| | | ... | ${dut}-vhost-${number}-if2
| | | ${dut_xconnect_if1}= | Set Variable If | ${number}==1 | ${${dut}_if1}
| | | ... | ${${dut}-vhost-${prev_index}-if2}
| | | Configure L2XC | ${nodes['${dut}']} | ${dut_xconnect_if1}
| | | ... | ${${dut}-vhost-${number}-if1}
| | | Run Keyword If | ${number}==${vm_count} | Configure L2XC
| | | ... | ${nodes['${dut}']} | ${${dut}-vhost-${number}-if2} | ${${dut}_if2}
| | All VPP Interfaces Ready Wait | ${nodes}

| Initialize L2 xconnect with Vhost-User
| | [Documentation]
| | ... | Create pairs of Vhost-User interfaces for defined number of VMs on
| | ... | all VPP nodes. Add each Vhost-User interface into L2 cross-connect
| | ... | with with physical inteface or Vhost-User interface of another VM.
| | ...
| | ... | *Arguments:*
| | ... | - vm_count - VM count. Type: integer
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 xconnect with Vhost-User \| 1 \|
| | ...
| | [Arguments] | ${vm_count}=${1}
| | ...
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | Initialize L2 xconnect with Vhost-User on node | ${dut}
| | | ... | vm_count=${vm_count}

| Initialize L2 xconnect with Vhost-User and VLAN in 3-node circular topology
| | [Documentation]
| | ... | Create two Vhost-User interfaces on all defined VPP nodes. Cross
| | ... | connect each Vhost interface with one physical interface.
| | ... | Setup VLAN between DUTs. All interfaces are brought up.
| | ...
| | ... | *Arguments:*
| | ... | - sock1 - Socket path for first Vhost-User interface. Type: string
| | ... | - sock2 - Socket path for second Vhost-User interface. Type: string
| | ... | - subid - ID of the sub-interface to be created. Type: string
| | ... | - tag_rewrite - Method of tag rewrite. Type: string
| | ...
| | ... | *Example:*
| | ...
| | ... | \| L2 xconnect with Vhost-User and VLAN initialized in a 3-node\
| | ... | circular topology \| /tmp/sock1 \| /tmp/sock2 \| 10 \| pop-1 \|
| | ...
| | [Arguments] | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
| | ...
| | Set interfaces in path up
| | Initialize VLAN dot1q sub-interfaces in 3-node circular topology
| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid}
| | Configure L2 tag rewrite method on interfaces
| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2}
| | ... | ${tag_rewrite}
| | Configure vhost interfaces for L2BD forwarding | ${dut1}
| | ... | ${sock1} | ${sock2}
| | Configure L2XC | ${dut1} | ${dut1_if1} | ${vhost_if1}
| | Configure L2XC | ${dut1} | ${subif_index_1} | ${vhost_if2}
| | Configure vhost interfaces for L2BD forwarding | ${dut2}
| | ... | ${sock1} | ${sock2}
| | Configure L2XC | ${dut2} | ${subif_index_2} | ${vhost_if1}
| | Configure L2XC | ${dut2} | ${dut2_if2} | ${vhost_if2}

| Initialize L2 xconnect with Vhost-User and VLAN with DPDK link bonding in 3-node circular topology
| | [Documentation]
| | ... | Create two Vhost-User interfaces on all defined VPP nodes. Setup VLAN
| | ... | on BondEthernet interfaces between DUTs. Cross connect one Vhost
| | ... | interface with physical interface towards TG and other Vhost interface
| | ... | with VLAN sub-interface. All interfaces are brought up.
| | ...
| | ... | *Arguments:*
| | ... | - sock1 - Socket path for first Vhost-User interface. Type: string
| | ... | - sock2 - Socket path for second Vhost-User interface. Type: string
| | ... | - subid - ID of the sub-interface to be created. Type: string
| | ... | - tag_rewrite - Method of tag rewrite. Type: string
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 xconnect with Vhost-User and VLAN with DPDK link\
| | ... | bonding in 3-node circular topology \| /tmp/sock1 \| /tmp/sock2 \
| | ... | \| 10 \| pop-1 \|
| | ...
| | [Arguments] | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite}
| | ...
| | Set interfaces in path up
| | Add DPDK bonded ethernet interfaces to topology file in 3-node single link topology
| | Set Interface State | ${dut1} | ${dut1_eth_bond_if1} | up
| | VPP Set interface MTU | ${dut1} | ${dut1_eth_bond_if1}
| | Set Interface State | ${dut2} | ${dut2_eth_bond_if1} | up
| | VPP Set interface MTU | ${dut2} | ${dut2_eth_bond_if1}
| | Initialize VLAN dot1q sub-interfaces in 3-node circular topology
| | ... | ${dut1} | ${dut1_eth_bond_if1} | ${dut2} | ${dut2_eth_bond_if1}
| | ... | ${subid}
| | Configure L2 tag rewrite method on interfaces
| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2}
| | ... | ${tag_rewrite}
| | Configure vhost interfaces for L2BD forwarding | ${dut1}
| | ... | ${sock1} | ${sock2}
| | Configure L2XC | ${dut1} | ${dut1_if1} | ${vhost_if1}
| | Configure L2XC | ${dut1} | ${subif_index_1} | ${vhost_if2}
| | Configure vhost interfaces for L2BD forwarding | ${dut2}
| | ... | ${sock1} | ${sock2}
| | Configure L2XC | ${dut2} | ${subif_index_2} | ${vhost_if1}
| | Configure L2XC | ${dut2} | ${dut2_if2} | ${vhost_if2}
| | All VPP Interfaces Ready Wait | ${nodes}

| Initialize L2 xconnect with Vhost-User and VLAN with VPP link bonding in 3-node circular topology
| | [Documentation]
| | ... | Create two Vhost-User interfaces on all defined VPP nodes. Create one
| | ... | link bonding (BondEthernet) interface on both VPP nodes. Enslave one
| | ... | physical interface towards next DUT by BondEthernet interface. Setup
| | ... | VLAN on BondEthernet interfaces between DUTs. Cross connect one Vhost
| | ... | interface with physical interface towards TG and other Vhost interface
| | ... | with VLAN sub-interface. All interfaces are brought up.
| | ...
| | ... | *Arguments:*
| | ... | - sock1 - Socket path for first Vhost-User interface. Type: string
| | ... | - sock2 - Socket path for second Vhost-User interface. Type: string
| | ... | - subid - ID of the sub-interface to be created. Type: string
| | ... | - tag_rewrite - Method of tag rewrite. Type: string
| | ... | - bond_mode - Link bonding mode. Type: string
| | ... | - lb_mode - Load balance mode. Type: string
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 xconnect with Vhost-User and VLAN with VPP link\
| | ... | bonding in 3-node circular topology \| /tmp/sock1 \| /tmp/sock2 \
| | ... | \| 10 \| pop-1 \| \| xor \| l34 \|
| | ...
| | [Arguments] | ${sock1} | ${sock2} | ${subid} | ${tag_rewrite} | ${bond_mode}
| | ... | ${lb_mode}
| | ...
| | Set interfaces in path up
| | ${dut1_eth_bond_if1}= | VPP Create Bond Interface | ${dut1} | ${bond_mode}
| | ... | ${lb_mode}
| | Set Interface State | ${dut1} | ${dut1_eth_bond_if1} | up
| | VPP Set interface MTU | ${dut1} | ${dut1_eth_bond_if1}
| | ${if2_status} | ${value}= | Run Keyword And Ignore Error
| | ... | Variable Should Exist | ${dut1_if2}
| | Run Keyword If | '${if2_status}' == 'PASS'
| | ... | VPP Enslave Physical Interface | ${dut1} | ${dut1_if2}
| | ... | ${dut1_eth_bond_if1}
| | ... | ELSE
| | ... | VPP Enslave Physical Interface | ${dut1} | ${dut1_if2_1}
| | ... | ${dut1_eth_bond_if1}
| | Run Keyword Unless | '${if2_status}' == 'PASS'
| | ... | VPP Enslave Physical Interface | ${dut1} | ${dut1_if2_2}
| | ... | ${dut1_eth_bond_if1}
| | ${dut2_eth_bond_if1}= | VPP Create Bond Interface | ${dut2} | ${bond_mode}
| | ... | ${lb_mode}
| | Set Interface State | ${dut2} | ${dut2_eth_bond_if1} | up
| | VPP Set interface MTU | ${dut1} | ${dut1_eth_bond_if1}
| | ${if1_status} | ${value}= | Run Keyword And Ignore Error
| | ... | Variable Should Exist | ${dut2_if1}
| | Run Keyword If | '${if1_status}' == 'PASS'
| | ... | VPP Enslave Physical Interface | ${dut2} | ${dut2_if1}
| | ... | ${dut2_eth_bond_if1}
| | ... | ELSE
| | ... | VPP Enslave Physical Interface | ${dut2} | ${dut2_if1_1}
| | ... | ${dut2_eth_bond_if1}
| | Run Keyword Unless | '${if2_status}' == 'PASS'
| | ... | VPP Enslave Physical Interface | ${dut2} | ${dut2_if1_2}
| | ... | ${dut2_eth_bond_if1}
| | VPP Show Bond Data On All Nodes | ${nodes} | details=${TRUE}
| | Initialize VLAN dot1q sub-interfaces in 3-node circular topology
| | ... | ${dut1} | ${dut1_eth_bond_if1} | ${dut2} | ${dut2_eth_bond_if1}
| | ... | ${subid}
| | Configure L2 tag rewrite method on interfaces
| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2}
| | ... | ${tag_rewrite}
| | Configure vhost interfaces for L2BD forwarding | ${dut1}
| | ... | ${sock1} | ${sock2}
| | Configure L2XC | ${dut1} | ${dut1_if1} | ${vhost_if1}
| | Configure L2XC | ${dut1} | ${subif_index_1} | ${vhost_if2}
| | Configure vhost interfaces for L2BD forwarding | ${dut2}
| | ... | ${sock1} | ${sock2}
| | Configure L2XC | ${dut2} | ${subif_index_2} | ${vhost_if1}
| | Configure L2XC | ${dut2} | ${dut2_if2} | ${vhost_if2}

| Initialize L2 bridge domain in 2-node circular topology
| | [Documentation]
| | ... | Setup L2 DB topology by adding two interfaces on DUT into BD
| | ... | that is created automatically with index 1. Learning is enabled.
| | ... | Interfaces are brought up.
| | ...
| | ... | *Arguments:*
| | ... | - bd_id - Bridge domain ID. Type: integer
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 bridge domain in 2-node circular topology \| 1 \|
| | ...
| | [Arguments] | ${bd_id}=${1}
| | ...
| | Set interfaces in path up
| | Add interface to bridge domain | ${dut1} | ${dut1_if1} | ${bd_id}
| | Add interface to bridge domain | ${dut1} | ${dut1_if2} | ${bd_id}

| Initialize L2 bridge domain in 3-node circular topology
| | [Documentation]
| | ... | Setup L2 DB topology by adding two interfaces on each DUT into BD
| | ... | that is created automatically with index 1. Learning is enabled.
| | ... | Interfaces are brought up.
| | ...
| | ... | *Arguments:*
| | ... | - bd_id - Bridge domain ID. Type: integer
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 bridge domain in 3-node circular topology \| 1 \|
| | ...
| | [Arguments] | ${bd_id}=${1}
| | ...
| | Set interfaces in path up
| | Add interface to bridge domain | ${dut1} | ${dut1_if1} | ${bd_id}
| | Add interface to bridge domain | ${dut1} | ${dut1_if2} | ${bd_id}
| | Add interface to bridge domain | ${dut2} | ${dut2_if1} | ${bd_id}
| | Add interface to bridge domain | ${dut2} | ${dut2_if2} | ${bd_id}

| Configure IPv4 ACLs
| | [Documentation]
| | ... | Configure ACL with required number of not-hitting permit ACEs plus two
| | ... | hitting ACEs for both traffic directions.
| | ...
| | ... | *Arguments:*
| | ... | - dut_node - DUT node. Type: dictionary
| | ... | - dut_if1 - DUT node interface1 name (Optional). Type: string
| | ... | - dut_if2 - DUT node interface2 name (Optional). Type: string
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Configure IPv4 ACLs \| ${nodes['DUT1']} \| GigabitEthernet0/7/0 \
| | ... | \| GigabitEthernet0/8/0 \|
| | ...
| | ... | _NOTE:_ This KW uses following test case variables:
| | ... | - ${src_ip_start} - Source IP address start. Type: string
| | ... | - ${dst_ip_start} - Destination IP address start. Type: string
| | ... | - ${ip_step} - IP address step. Type: string
| | ... | - ${sport_start} - Source port number start. Type: string
| | ... | - ${dport_start} - Destination port number start. Type: string
| | ... | - ${port_step} - Port number step. Type: string
| | ... | - ${no_hit_aces_number} - Number of not-hitting ACEs to be configured.
| | ... | Type: integer
| | ... | - ${acl_apply_type} - To what path apply the ACL - input or output.
| | ... | Type: string
| | ... | - ${acl_action} - Action for the rule - deny, permit, permit+reflect.
| | ... | Type: string
| | ... | - ${trex_stream1_subnet} - IP subnet used by T-Rex in direction 0->1.
| | ... | Type: string
| | ... | - ${trex_stream2_subnet} - IP subnet used by T-Rex in direction 1->0.
| | ... | Type: string
| | ...
| | [Arguments] | ${dut} | ${dut_if1}=${NONE} | ${dut_if2}=${NONE}
| | ${src_ip_int} = | Evaluate
| | ... | int(ipaddress.ip_address(unicode($src_ip_start))) - $ip_step
| | ... | modules=ipaddress
| | ${dst_ip_int} = | Evaluate
| | ... | int(ipaddress.ip_address(unicode($dst_ip_start))) - $ip_step
| | ... | modules=ipaddress
| | ${ip_limit} = | Set Variable | 255.255.255.255
| | ${ip_limit_int} = | Evaluate
| | ... | int(ipaddress.ip_address(unicode($ip_limit))) | modules=ipaddress
| | ${sport}= | Evaluate | $sport_start - $port_step
| | ${dport}= | Evaluate | $dport_start - $port_step
| | ${port_limit}= | Set Variable | ${65535}
| | ${acl}= | Set Variable | ipv4 permit
| | :FOR | ${nr} | IN RANGE | 0 | ${no_hit_aces_number}
| | | ${src_ip_int} = | Evaluate | $src_ip_int + $ip_step
| | | ${dst_ip_int} = | Evaluate | $dst_ip_int + $ip_step
| | | ${sport}= | Evaluate | $sport + $port_step
| | | ${dport}= | Evaluate | $dport + $port_step
| | | ${ipv4_limit_reached}= | Set Variable If
| | | ... | $src_ip_int > $ip_limit_int or $src_ip_int > $ip_limit_int
| | | ... | ${TRUE}
| | | ${udp_limit_reached}= | Set Variable If
| | | ... | $sport > $port_limit or $dport > $port_limit | ${TRUE}
| | | Run Keyword If | $ipv4_limit_reached is True | Log
| | | ... | Can't do more iterations - IPv4 address limit has been reached.
| | | ... | WARN
| | | Run Keyword If | $udp_limit_reached is True | Log
| | | ... | Can't do more iterations - UDP port limit has been reached.
| | | ... | WARN
| | | ${src_ip} = | Run Keyword If | $ipv4_limit_reached is True
| | | ... | Set Variable | ${ip_limit}
| | | ... | ELSE | Evaluate | str(ipaddress.ip_address($src_ip_int))
| | | ... | modules=ipaddress
| | | ${dst_ip} = | Run Keyword If | $ipv4_limit_reached is True
| | | ... | Set Variable | ${ip_limit}
| | | ... | ELSE | Evaluate | str(ipaddress.ip_address($dst_ip_int))
| | | ... | modules=ipaddress
| | | ${sport}= | Set Variable If | ${sport} > $port_limit | $port_limit
| | | ... | ${sport}
| | | ${dport}= | Set Variable If | ${dport} > $port_limit | $port_limit
| | | ... | ${dport}
| | | ${acl}= | Catenate | ${acl} | src ${src_ip}/32 dst ${dst_ip}/32
| | | ... | sport ${sport} | dport ${dport},
| | | Exit For Loop If
| | | ... | $ipv4_limit_reached is True or $udp_limit_reached is True
| | ${acl}= | Catenate | ${acl}
| | ... | ipv4 ${acl_action} src ${trex_stream1_subnet},
| | ... | ipv4 ${acl_action} src ${trex_stream2_subnet}
| | Add Replace Acl Multi Entries | ${dut} | rules=${acl}
| | @{acl_list}= | Create List | ${0}
| | Run Keyword If | 'input' in $acl_apply_type and $dut_if1 is not None
| | ... | Set Acl List For Interface | ${dut} | ${dut_if1} | input | ${acl_list}
| | Run Keyword If | 'input' in $acl_apply_type and $dut_if2 is not None
| | ... | Set Acl List For Interface | ${dut} | ${dut_if2} | input | ${acl_list}
| | Run Keyword If | 'output' in $acl_apply_type and $dut_if1 is not None
| | ... | Set Acl List For Interface | ${dut} | ${dut_if1} | output
| | ... | ${acl_list}
| | Run Keyword If | 'output' in $acl_apply_type and $dut_if2 is not None
| | ... | Set Acl List For Interface | ${dut} | ${dut_if2} | output
| | ... | ${acl_list}

| Initialize L2 bridge domain with IPv4 ACLs on DUT1 in 3-node circular topology
| | [Documentation]
| | ... | Setup L2BD topology by adding two interfaces on DUT1 into bridge
| | ... | domain that is created automatically with index 1. Learning is
| | ... | enabled. Interfaces are brought up. Apply required ACL rules to DUT1
| | ... | interfaces.
| | ...
| | ... | *Arguments:*
| | ... | _None_
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 bridge domain with IPv4 ACLs on DUT1 in 3-node \
| | ... | circular topology \|
| | ...
| | ... | _NOTE:_ This KW uses following test case variables:
| | ... | - ${dut1} - DUT1 node.
| | ... | - ${dut2} - DUT2 node.
| | ... | - ${dut1_if1} - DUT1 interface towards TG.
| | ... | - ${dut1_if2} - DUT1 interface towards DUT2.
| | ... | - ${dut2_if1} - DUT2 interface towards DUT1.
| | ... | - ${dut2_if2} - DUT2 interface towards TG.
| | ...
| | Set interfaces in path up
| | Configure L2BD forwarding | ${dut1} | ${dut1_if1} | ${dut1_if2}
| | Configure L2XC | ${dut2} | ${dut2_if1} | ${dut2_if2}
| | Configure IPv4 ACLs | ${dut1} | ${dut1_if1} | ${dut1_if2}

| Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | [Documentation]
| | ... | Set UP state on VPP interfaces in path on nodes in 2-node / 3-node
| | ... | circular topology. Get the interface MAC addresses and setup ARP on
| | ... | all VPP interfaces. Setup IPv4 addresses with /24 prefix on DUT-TG
| | ... | links. In case of 3-node topology setup IPv4 adresses with /30 prefix
| | ... | on DUT1-DUT2 link and set routing on both DUT nodes with prefix /24
| | ... | and next hop of neighbour DUT interface IPv4 address.
| | ... | Apply required ACL rules to DUT1 interfaces.
| | ...
| | ... | *Arguments:*
| | ... | - ip_nr - Number of IPs to be used. Type: integer or string
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize IPv4 routing for '10' addresses with IPv4 ACLs on DUT1 \
| | ... | in 3-node circular topology \|
| | ...
| | ... | _NOTE:_ This KW uses following test case variables:
| | ... | - ${tg} - TG node.
| | ... | - ${dut1} - DUT1 node.
| | ... | - ${dut2} - DUT2 node.
| | ... | - ${tg_if1} - TG interface 1 towards DUT1.
| | ... | - ${tg_if2} - TG interface 2 towards DUT2 (3-node topo) or DUT1
| | ... | (2-node topo).
| | ... | - ${dut1_if1} - DUT1 interface 1 towards TG.
| | ... | - ${dut1_if2} - DUT1 interface 2 towards DUT2 (3-node topo) or TG
| | ... | (2-node topo).
| | ... | - ${dut2_if1} - DUT2 interface 1 towards DUT1.
| | ... | - ${dut2_if2} - DUT2 interface 2 towards TG.
| | ...
| | ${dut2_status} | ${value}= | Run Keyword And Ignore Error
| | ... | Variable Should Exist | ${dut2}
| | ${dut}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Set Variable | ${dut2}
| | ... | ELSE | Set Variable | ${dut1}
| | ${dut_if2}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Set Variable | ${dut2_if2}
| | ... | ELSE | Set Variable | ${dut1_if2}
| | ...
| | Set interfaces in path up
| | ...
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | ${dut1_if2_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Get Interface MAC | ${dut2} | ${dut2_if1}
| | ...
| | :FOR | ${number} | IN RANGE | 2 | ${ip_nr}+2
| | | Add arp on dut | ${dut1} | ${dut1_if1} | 10.10.10.${number}
| | | ... | ${tg1_if1_mac}
| | | Add arp on dut | ${dut} | ${dut_if2} | 20.20.20.${number}
| | | ... | ${tg1_if2_mac}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Add arp on dut | ${dut1} | ${dut1_if2} | 1.1.1.2 | ${dut2_if1_mac}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Add arp on dut | ${dut2} | ${dut2_if1} | 1.1.1.1 | ${dut1_if2_mac}
| | ...
| | Configure IP addresses on interfaces
| | ... | ${dut1} | ${dut1_if1} | 10.10.10.1 | 24
| | ... | ${dut} | ${dut_if2} | 20.20.20.1 | 24
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Configure IP addresses on interfaces
| | ... | ${dut1} | ${dut1_if2} | 1.1.1.1 | 30
| | ... | ${dut2} | ${dut2_if1} | 1.1.1.2 | 30
| | ...
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Vpp Route Add | ${dut1} | 20.20.20.0 | 24 | 1.1.1.2 | ${dut1_if2}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Vpp Route Add | ${dut2} | 10.10.10.0 | 24 | 1.1.1.1 | ${dut2_if1}
| | ...
| | Configure IPv4 ACLs | ${dut1} | ${dut1_if1} | ${dut1_if2}

| Configure MACIP ACLs
| | [Documentation]
| | ... | Configure MACIP ACL with required number of not-hitting permit ACEs
| | ... | plus two hitting ACEs for both traffic directions.
| | ...
| | ... | *Arguments:*
| | ... | - dut_node - DUT node. Type: dictionary
| | ... | - dut_if1 - DUT node interface1 name (Optional). Type: string
| | ... | - dut_if2 - DUT node interface2 name (Optional). Type: string
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Configure MACIP ACLs \| ${nodes['DUT1']} \| GigabitEthernet0/7/0 \
| | ... | \| GigabitEthernet0/8/0 \|
| | ...
| | ... | _NOTE:_ This KW uses following test case variables:
| | ... | - ${src_ip_start} - Source IP address start. Type: string
| | ... | - ${ip_step} - IP address step. Type: string
| | ... | - ${src_mac_start} - Source MAC address start in format with colons.
| | ... | Type: string
| | ... | - ${src_mac_step} - Source MAC address step. Type: string
| | ... | - ${src_mac_mask} - Source MAC address mask. 00:00:00:00:00:00 is a
| | ... | wildcard mask. Type: string
| | ... | - ${no_hit_aces_number} - Number of not-hitting ACEs to be configured.
| | ... | Type: integer
| | ... | - ${acl_action} - Action for the rule - deny, permit, permit+reflect.
| | ... | Type: string
| | ... | - ${tg_stream1_subnet} - IP subnet used by TG in direction 0->1.
| | ... | Type: string
| | ... | - ${tg_stream2_subnet} - IP subnet used by TG in direction 1->0.
| | ... | Type: string
| | ... | - ${tg_stream1_mac} - Source MAC address of traffic stream 1.
| | ... | Type: string
| | ... | - ${tg_stream2_mac} - Source MAC address of traffic stream 2.
| | ... | Type: string
| | ... | - ${tg_mac_mask} - MAC address mask for traffic streams.
| | ... | 00:00:00:00:00:00 is a wildcard mask. Type: string
| | ...
| | [Arguments] | ${dut} | ${dut_if1}=${NONE} | ${dut_if2}=${NONE}
| | ...
| | ${src_ip_int} = | IP To Int | ${src_ip_start}
| | ${src_ip_int} = | Evaluate | ${src_ip_int} - ${ip_step}
| | ...
| | ${ip_limit} = | Set Variable | 255.255.255.255
| | ${ip_limit_int} = | IP To Int | ${ip_limit}
| | ...
| | ${src_mac_int} = | Mac To Int | ${src_mac_start}
| | ${src_mac_int} = | Evaluate | ${src_mac_int} - ${src_mac_step}
| | ...
| | ${mac_limit} = | Set Variable | ff:ff:ff:ff:ff:ff
| | ${mac_limit_int} = | Mac To Int | ${mac_limit}
| | ...
| | ${acl}= | Set Variable | ipv4 permit
| | :FOR | ${nr} | IN RANGE | 0 | ${no_hit_aces_number}
| | | ${src_ip_int} = | Evaluate | ${src_ip_int} + ${ip_step}
| | | ${src_mac_int} = | Evaluate | ${src_mac_int} + ${src_mac_step}
| | | ${ipv4_limit_reached}= | Set Variable If
| | | ... | ${src_ip_int} > ${ip_limit_int} | ${TRUE}
| | | ${mac_limit_reached}= | Set Variable If
| | | ... | ${src_mac_int} > ${mac_limit_int} | ${TRUE}
| | | Run Keyword If | '${ipv4_limit_reached}' == '${TRUE}' | Log
| | | ... | Can't do more iterations - IPv4 address limit has been reached.
| | | ... | WARN
| | | Run Keyword If | '${mac_limit_reached}' == '${TRUE}' | Log
| | | ... | Can't do more iterations - MAC address limit has been reached.
| | | ... | WARN
| | | ${src_ip} = | Run Keyword If | '${ipv4_limit_reached}' == '${TRUE}'
| | | ... | Set Variable | ${ip_limit}
| | | ... | ELSE | Int To IP | ${src_ip_int}
| | | ${src_mac}= | Run Keyword If | '${mac_limit_reached}' == '${TRUE}'
| | | ... | Set Variable | ${mac_limit}
| | | ... | ELSE | Int To Mac | ${src_mac_int}
| | | ${acl}= | Catenate | ${acl} | ip ${src_ip}/32
| | | ... | mac ${src_mac} | mask ${src_mac_mask},
| | | Exit For Loop If | '${ipv4_limit_reached}' == '${TRUE}' or '${mac_limit_reached}' == '${TRUE}'
| | ${acl0}= | Catenate | ${acl}
| | ... | ipv4 ${acl_action} ip ${tg_stream1_subnet} mac ${tg_stream1_mac}
| | ... | mask ${tg_mac_mask}
| | ${acl1}= | Catenate | ${acl}
| | ... | ipv4 ${acl_action} ip ${tg_stream2_subnet} mac ${tg_stream2_mac}
| | ... | mask ${tg_mac_mask}
| | Add Macip Acl Multi Entries | ${dut} | rules=${acl0}
| | Add Macip Acl Multi Entries | ${dut} | rules=${acl1}
| | ${acl_idx}= | Set Variable | 0
| | Run Keyword Unless | '${dut_if1}' == '${NONE}'
| | ... | Add Del Macip Acl Interface | ${dut} | ${dut_if1} | add | ${acl_idx}
| | ${acl_idx}= | Set Variable | 1
| | Run Keyword Unless | '${dut_if2}' == '${NONE}'
| | ... | Add Del Macip Acl Interface | ${dut} | ${dut_if2} | add | ${acl_idx}

| Initialize L2 bridge domain with MACIP ACLs on DUT1 in 3-node circular topology
| | [Documentation]
| | ... | Setup L2BD topology by adding two interfaces on DUT1 into bridge
| | ... | domain that is created automatically with index 1. Learning is
| | ... | enabled. Interfaces are brought up. Apply required MACIP ACL rules to
| | ... | DUT1 interfaces.
| | ...
| | ... | *Arguments:*
| | ... | _None_
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 bridge domain with MACIP ACLs on DUT1 in 3-node \
| | ... | circular topology \|
| | ...
| | ... | _NOTE 1:_ This KW uses following test case variables:
| | ... | - ${tg} - TG node.
| | ... | - ${dut1} - DUT1 node.
| | ... | - ${dut2} - DUT2 node.
| | ... | - ${tg_if1} - TG interface towards DUT1.
| | ... | - ${tg_if2} - TG interface towards DUT2.
| | ... | - ${dut1_if1} - DUT1 interface towards TG.
| | ... | - ${dut1_if2} - DUT1 interface towards DUT2.
| | ... | - ${dut2_if1} - DUT2 interface towards DUT1.
| | ... | - ${dut2_if2} - DUT2 interface towards TG.
| | ...
| | Set interfaces in path up
| | Configure L2BD forwarding | ${dut1} | ${dut1_if1} | ${dut1_if2}
| | Configure L2XC | ${dut2} | ${dut2_if1} | ${dut2_if2}
| | Configure MACIP ACLs | ${dut1} | ${dut1_if1} | ${dut1_if2}

| Initialize L2 bridge domains with Vhost-User on node
| | [Documentation]
| | ... | Create pairs of Vhost-User interfaces for defined number of VMs on
| | ... | defined VPP node. Add each Vhost-User interface into L2 bridge
| | ... | domains with learning enabled with physical inteface or Vhost-User
| | ... | interface of another VM.
| | ...
| | ... | *Arguments:*
| | ... | - dut - DUT node. Type: string
| | ... | - vm_count - VM count. Type: integer
| | ...
| | ... | *Note:*
| | ... | Socket paths for VM are defined in following format:
| | ... | - /tmp/sock-${VM_ID}-1
| | ... | - /tmp/sock-${VM_ID}-2
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 bridge domains with Vhost-User on node \| DUT1 \
| | ... | \| 1 \|
| | ...
| | [Arguments] | ${dut} | ${vm_count}=${1}
| | ...
| | ${bd_id2}= | Evaluate | ${vm_count}+1
| | Add interface to bridge domain | ${nodes['${dut}']}
| | ... | ${${dut}_if1} | ${1}
| | Add interface to bridge domain | ${nodes['${dut}']}
| | ... | ${${dut}_if2} | ${bd_id2}
| | :FOR | ${number} | IN RANGE | 1 | ${vm_count}+1
| | | ${sock1}= | Set Variable | /tmp/sock-${number}-1
| | | ${sock2}= | Set Variable | /tmp/sock-${number}-2
| | | Configure vhost interfaces for L2BD forwarding | ${nodes['${dut}']}
| | | ... | ${sock1} | ${sock2} | ${dut}-vhost-${number}-if1
| | | ... | ${dut}-vhost-${number}-if2
| | | ${bd_id2}= | Evaluate | ${number}+1
| | | Add interface to bridge domain | ${nodes['${dut}']}
| | | ... | ${${dut}-vhost-${number}-if1} | ${number}
| | | Add interface to bridge domain | ${nodes['${dut}']}
| | | ... | ${${dut}-vhost-${number}-if2} | ${bd_id2}
| | All VPP Interfaces Ready Wait | ${nodes}

| Initialize L2 bridge domains with Vhost-User
| | [Documentation]
| | ... | Create pairs of Vhost-User interfaces for defined number of VMs on all
| | ... | defined VPP nodes. Add each Vhost-User interface into L2 bridge
| | ... | domains with learning enabled with physical inteface or Vhost-User
| | ... | interface of another VM.
| | ...
| | ... | *Arguments:*
| | ... | - vm_count - VM count. Type: integer
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 bridge domains with Vhost-User \| 1 \|
| | ...
| | [Arguments] | ${vm_count}=${1}
| | ...
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | Initialize L2 bridge domains with Vhost-User on node | ${dut}
| | | ... | vm_count=${vm_count}

| Initialize L2 bridge domain with VXLANoIPv4 in 3-node circular topology
| | [Documentation]
| | ... | Setup L2 bridge domain topology with VXLANoIPv4 by connecting
| | ... | physical and vxlan interfaces on each DUT. All interfaces are brought
| | ... | up. IPv4 addresses with prefix /24 are configured on interfaces
| | ... | between DUTs. VXLAN sub-interfaces has same IPv4 address as
| | ... | interfaces.
| | ...
| | Set interfaces in path up
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2} | 172.16.0.1
| | ... | 24
| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if1} | 172.16.0.2
| | ... | 24
| | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
| | Add arp on dut | ${dut1} | ${dut1_if2} | 172.16.0.2 | ${dut2_if1_mac}
| | Add arp on dut | ${dut2} | ${dut2_if1} | 172.16.0.1 | ${dut1_if2_mac}
| | ${dut1s_vxlan}= | Create VXLAN interface | ${dut1} | 24
| | ... | 172.16.0.1 | 172.16.0.2
| | ${dut2s_vxlan}= | Create VXLAN interface | ${dut2} | 24
| | ... | 172.16.0.2 | 172.16.0.1
| | Configure L2BD forwarding | ${dut1} | ${dut1_if1} | ${dut1s_vxlan}
| | Configure L2BD forwarding | ${dut2} | ${dut2_if2} | ${dut2s_vxlan}

| Initialize L2 bridge domains with Vhost-User and VXLANoIPv4 in 3-node circular topology
| | [Documentation]
| | ... | Create two Vhost-User interfaces on all defined VPP nodes. Add each
| | ... | Vhost-User interface into L2 bridge domains with learning enabled
| | ... | with physical inteface.
| | ... | Setup VXLANoIPv4 between DUTs by connecting physical and vxlan
| | ... | interfaces on each DUT. All interfaces are brought up.
| | ... | IPv4 addresses with prefix /24 are configured on interfaces between
| | ... | DUTs. VXLAN sub-interfaces has same IPv4 address as interfaces.
| | ...
| | ... | *Arguments:*
| | ... | - bd_id1 - Bridge domain ID. Type: integer
| | ... | - bd_id2 - Bridge domain ID. Type: integer
| | ... | - sock1 - Sock path for first Vhost-User interface. Type: string
| | ... | - sock2 - Sock path for second Vhost-User interface. Type: string
| | ...
| | ... | *Example:*
| | ...
| | ... | \| L2 bridge domains with Vhost-User and VXLANoIPv4 initialized in a\
| | ... | 3-node circular topology \| 1 \| 2 \| /tmp/sock1 \| /tmp/sock2 \|
| | ...
| | [Arguments] | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
| | ...
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2} | 172.16.0.1
| | ... | 24
| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if1} | 172.16.0.2
| | ... | 24
| | Set interfaces in path up
| | ${dut1s_vxlan}= | Create VXLAN interface | ${dut1} | 24
| | ... | 172.16.0.1 | 172.16.0.2
| | ${dut2s_vxlan}= | Create VXLAN interface | ${dut2} | 24
| | ... | 172.16.0.2 | 172.16.0.1
| | Configure vhost interfaces for L2BD forwarding | ${dut1}
| | ... | ${sock1} | ${sock2}
| | Add interface to bridge domain | ${dut1} | ${dut1_if1} | ${bd_id1}
| | Add interface to bridge domain | ${dut1} | ${vhost_if1} | ${bd_id1}
| | Add interface to bridge domain | ${dut1} | ${vhost_if2} | ${bd_id2}
| | Add interface to bridge domain | ${dut1} | ${dut1s_vxlan} | ${bd_id2}
| | Configure vhost interfaces for L2BD forwarding | ${dut2}
| | ... | ${sock1} | ${sock2}
| | Add interface to bridge domain | ${dut2} | ${dut2s_vxlan} | ${bd_id1}
| | Add interface to bridge domain | ${dut2} | ${vhost_if1} | ${bd_id1}
| | Add interface to bridge domain | ${dut2} | ${vhost_if2} | ${bd_id2}
| | Add interface to bridge domain | ${dut2} | ${dut2_if2} | ${bd_id2}

| Init L2 bridge domains with single DUT with Vhost-User and VXLANoIPv4 in 3-node circular topology
| | [Documentation]
| | ... | Create two Vhost-User interfaces on one VPP node. Add each
| | ... | Vhost-User interface into L2 bridge domains with learning enabled
| | ... | one connected to physical interface, the other to VXLAN.
| | ... | Setup VXLANoIPv4 between DUTs and TG by connecting physical and vxlan
| | ... | interfaces on the DUT. All interfaces are brought up.
| | ... | IPv4 addresses with prefix /24 are configured on interfaces between
| | ... | DUT and TG.
| | ...
| | ... | *Arguments:*
| | ... | - dut1_address - Address of physical interface on DUT1. Type: string
| | ... | - dut1_address_subnet - Subnet of the address of physical interface on
| | ... |                         DUT1. Type: string
| | ... | - dut2_address - Address of physical interface on DUT2. Type: string
| | ... | - dut2_address_subnet - Subnet of the address of physical interface on
| | ... |                         DUT2. Type: string
| | ... | - dut1_gw - Address of the _gateway_ to which the traffic will be
| | ... |             forwarded on DUT1. Type: string
| | ... | - dut2_gw - Address of the _gateway_ to which the traffic will be
| | ... |             forwarded on DUT2. Type: string
| | ... | - dut1_vxlans - List of VXLAN params to be configured on DUT1.
| | ... |                 Type: list of dicts, dict params vni, vtep
| | ... | - dut2_vxlans - List of VXLAN params to be configured on DUT2.
| | ... |                 Type: list of dicts, dict params vni, vtep
| | ... | - dut1_route_subnet - Subnet address to forward to  _gateway_ on DUT1.
| | ... |                       Type: string
| | ... | - dut1_route_mask - Subnet address mask to forward to  _gateway_
| | ... |                     on DUT1. Type: string
| | ... | - dut2_route_subnet - Subnet address to forward to  _gateway_ on DUT2.
| | ... |                       Type: string
| | ... | - dut2_route_mask - Subnet address mask to forward to  _gateway_
| | ... |                     on DUT2. Type: string
| | ...
| | ... | *Example:*
| | ...
| | [Arguments] | ${dut1_address} | ${dut1_address_subnet} |
| | ... | ${dut2_address} | ${dut2_address_subnet} | ${dut1_gw} | ${dut2_gw} |
| | ... | ${dut1_vxlans} | ${dut2_vxlans} | ${dut1_route_subnet} |
| | ... | ${dut1_route_mask} | ${dut2_route_subnet} | ${dut2_route_mask}
| | ...
| | Set interfaces in path up
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if1} |
| | ... | ${dut1_address} | ${dut1_address_subnet}
| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if2} |
| | ... | ${dut2_address} | ${dut2_address_subnet}
| | ${dut1_bd_id1}= | Set Variable | 1
| | ${dut1_bd_id2}= | Set Variable | 2
| | ${dut2_bd_id1}= | Set Variable | 1
| | :FOR | ${vxlan} | IN | @{dut1_vxlans}
| | | ${dut1s_vxlan}= | Create VXLAN interface | ${dut1} | ${vxlan.vni}
| | | ... | ${dut1_address} | ${vxlan.vtep}
| | | Add interface to bridge domain | ${dut1} | ${dut1s_vxlan} | ${dut1_bd_id1}
| | :FOR | ${vxlan} | IN | @{dut2_vxlans}
| | | ${dut2s_vxlan}= | Create VXLAN interface | ${dut2} | ${vxlan.vni}
| | | ... | ${dut2_address} | ${vxlan.vtep}
| | | Add interface to bridge domain | ${dut2} | ${dut2s_vxlan} | ${dut2_bd_id1}
| | ${tg_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | Add arp on dut | ${dut1} | ${dut1_if1} | ${dut1_gw} | ${tg_if1_mac}
| | Add arp on dut | ${dut2} | ${dut2_if2} | ${dut2_gw} | ${tg_if2_mac}
| | Vpp Route Add | ${dut1} | ${dut1_route_subnet} | ${dut1_route_mask}
| | ... | ${dut1_gw} | ${dut1_if1}
| | Vpp Route Add | ${dut2} | ${dut2_route_subnet} | ${dut2_route_mask}
| | ... | ${dut2_gw} | ${dut2_if2}
| | Add interface to bridge domain | ${dut1} | ${dut1_if2} | ${dut1_bd_id2}
| | Add interface to bridge domain | ${dut2} | ${dut2_if1} | ${dut2_bd_id1}
| | Add interface to bridge domain | ${dut1} | ${vhost_if1} | ${dut1_bd_id1}
| | Add interface to bridge domain | ${dut1} | ${vhost_if2} | ${dut1_bd_id2}

| Initialize L2 bridge domains with VLAN dot1q sub-interfaces in a 3-node circular topology
| | [Documentation]
| | ... | Setup L2 bridge domain topology with learning enabled with VLAN
| | ... | between DUTs by connecting physical and vlan interfaces on each DUT.
| | ... | All interfaces are brought up.
| | ...
| | ... | *Arguments:*
| | ... | - bd_id1 - Bridge domain ID. Type: integer
| | ... | - bd_id2 - Bridge domain ID. Type: integer
| | ... | - subid - ID of the sub-interface to be created. Type: string
| | ... | - tag_rewrite - Method of tag rewrite. Type: string
| | ...
| | ... | _NOTE:_ This KW uses following test case variables:
| | ... | - ${dut1} - DUT1 node.
| | ... | - ${dut2} - DUT2 node.
| | ... | - ${dut1_if2} - DUT1 interface towards DUT2.
| | ... | - ${dut2_if1} - DUT2 interface towards DUT1.
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 bridge domains with VLAN dot1q sub-interfaces
| | ... | in a 3-node circular topology \| 1 \| 2 \| 10 \| pop-1 \|
| | ...
| | [Arguments] | ${bd_id1} | ${bd_id2} | ${subid} | ${tag_rewrite}
| | ...
| | Set interfaces in path up
| | Initialize VLAN dot1q sub-interfaces in 3-node circular topology
| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid}
| | Configure L2 tag rewrite method on interfaces
| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2}
| | ... | ${tag_rewrite}
| | Add interface to bridge domain | ${dut1} | ${dut1_if1} | ${bd_id1}
| | Add interface to bridge domain | ${dut1} | ${subif_index_1} | ${bd_id1}
| | Add interface to bridge domain | ${dut2} | ${subif_index_2} | ${bd_id2}
| | Add interface to bridge domain | ${dut2} | ${dut2_if2} | ${bd_id2}

| Initialize L2 bridge domains with Vhost-User and VLAN in a 3-node circular topology
| | [Documentation]
| | ... | Create two Vhost-User interfaces on all defined VPP nodes. Add each
| | ... | Vhost-User interface into L2 bridge domains with learning enabled
| | ... | with physical inteface.
| | ... | Setup VLAN between DUTs. All interfaces are brought up.
| | ...
| | ... | *Arguments:*
| | ... | - bd_id1 - Bridge domain ID. Type: integer
| | ... | - bd_id2 - Bridge domain ID. Type: integer
| | ... | - sock1 - Sock path for first Vhost-User interface. Type: string
| | ... | - sock2 - Sock path for second Vhost-User interface. Type: string
| | ... | - subid - ID of the sub-interface to be created. Type: string
| | ... | - tag_rewrite - Method of tag rewrite. Type: string
| | ...
| | ... | *Example:*
| | ...
| | ... | \| L2 bridge domains with Vhost-User and VLAN initialized in a 3-node\
| | ... | circular topology \| 1 \| 2 \| /tmp/sock1 \| /tmp/sock2 \| 10 \
| | ... | \| pop-1 \|
| | ...
| | [Arguments] | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
| | ... | ${tag_rewrite}
| | ...
| | Set interfaces in path up
| | Initialize VLAN dot1q sub-interfaces in 3-node circular topology
| | ... | ${dut1} | ${dut1_if2} | ${dut2} | ${dut2_if1} | ${subid}
| | Configure L2 tag rewrite method on interfaces
| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2}
| | ... | ${tag_rewrite}
| | Configure vhost interfaces for L2BD forwarding | ${dut1}
| | ... | ${sock1} | ${sock2}
| | Add interface to bridge domain | ${dut1} | ${dut1_if1} | ${bd_id1}
| | Add interface to bridge domain | ${dut1} | ${vhost_if1} | ${bd_id1}
| | Add interface to bridge domain | ${dut1} | ${vhost_if2} | ${bd_id2}
| | Add interface to bridge domain | ${dut1} | ${subif_index_1} | ${bd_id2}
| | Configure vhost interfaces for L2BD forwarding | ${dut2}
| | ... | ${sock1} | ${sock2}
| | Add interface to bridge domain | ${dut2} | ${subif_index_2} | ${bd_id1}
| | Add interface to bridge domain | ${dut2} | ${vhost_if1} | ${bd_id1}
| | Add interface to bridge domain | ${dut2} | ${vhost_if2} | ${bd_id2}
| | Add interface to bridge domain | ${dut2} | ${dut2_if2} | ${bd_id2}

| Initialize L2 bridge domains with Vhost-User and VLAN with DPDK link bonding in a 3-node circular topology
| | [Documentation]
| | ... | Create two Vhost-User interfaces on all defined VPP nodes. Setup VLAN
| | ... | on BondEthernet interfaces between DUTs. Add one Vhost-User interface
| | ... | into L2 bridge domains with learning enabled with physical interface
| | ... | towards TG and other Vhost-User interface into L2 bridge domains with
| | ... | learning enabled with VLAN sub-interface. All interfaces are brought
| | ... | up.
| | ...
| | ... | *Arguments:*
| | ... | - bd_id1 - Bridge domain ID. Type: integer
| | ... | - bd_id2 - Bridge domain ID. Type: integer
| | ... | - sock1 - Sock path for first Vhost-User interface. Type: string
| | ... | - sock2 - Sock path for second Vhost-User interface. Type: string
| | ... | - subid - ID of the sub-interface to be created. Type: string
| | ... | - tag_rewrite - Method of tag rewrite. Type: string
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 bridge domains with Vhost-User and VLAN with DPDK\
| | ... | link bonding in a 3-node circular topology \| 1 \| 2 \| /tmp/sock1 \
| | ... | \| /tmp/sock2 \| 10 \| pop-1 \|
| | ...
| | [Arguments] | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
| | ... | ${tag_rewrite}
| | ...
| | Set interfaces in path up
| | Add DPDK bonded ethernet interfaces to topology file in 3-node single link topology
| | Set Interface State | ${dut1} | ${dut1_eth_bond_if1} | up
| | VPP Set interface MTU | ${dut1} | ${dut1_eth_bond_if1}
| | Set Interface State | ${dut2} | ${dut2_eth_bond_if1} | up
| | VPP Set interface MTU | ${dut2} | ${dut2_eth_bond_if1}
| | Initialize VLAN dot1q sub-interfaces in 3-node circular topology
| | ... | ${dut1} | ${dut1_eth_bond_if1} | ${dut2} | ${dut2_eth_bond_if1}
| | ... | ${subid}
| | Configure L2 tag rewrite method on interfaces
| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2}
| | ... | ${tag_rewrite}
| | Configure vhost interfaces for L2BD forwarding | ${dut1}
| | ... | ${sock1} | ${sock2}
| | Add interface to bridge domain | ${dut1} | ${dut1_if1} | ${bd_id1}
| | Add interface to bridge domain | ${dut1} | ${vhost_if1} | ${bd_id1}
| | Add interface to bridge domain | ${dut1} | ${vhost_if2} | ${bd_id2}
| | Add interface to bridge domain | ${dut1} | ${subif_index_1} | ${bd_id2}
| | Configure vhost interfaces for L2BD forwarding | ${dut2}
| | ... | ${sock1} | ${sock2}
| | Add interface to bridge domain | ${dut2} | ${subif_index_2} | ${bd_id1}
| | Add interface to bridge domain | ${dut2} | ${vhost_if1} | ${bd_id1}
| | Add interface to bridge domain | ${dut2} | ${vhost_if2} | ${bd_id2}
| | Add interface to bridge domain | ${dut2} | ${dut2_if2} | ${bd_id2}

| Initialize L2 bridge domains with Vhost-User and VLAN with VPP link bonding in a 3-node circular topology
| | [Documentation]
| | ... | Create two Vhost-User interfaces on all defined VPP nodes. Create one
| | ... | link bonding (BondEthernet) interface on both VPP nodes. Enslave one
| | ... | physical interface towards next DUT by BondEthernet interface. Setup
| | ... | VLAN on BondEthernet interfaces between DUTs. Add one Vhost-User
| | ... | interface into L2 bridge domains with learning enabled with physical
| | ... | interface towards TG and other Vhost-User interface into L2 bridge
| | ... | domains with learning enabled with VLAN sub-interface. All interfaces
| | ... | are brought up.
| | ...
| | ... | *Arguments:*
| | ... | - bd_id1 - Bridge domain ID. Type: integer
| | ... | - bd_id2 - Bridge domain ID. Type: integer
| | ... | - sock1 - Sock path for first Vhost-User interface. Type: string
| | ... | - sock2 - Sock path for second Vhost-User interface. Type: string
| | ... | - subid - ID of the sub-interface to be created. Type: string
| | ... | - tag_rewrite - Method of tag rewrite. Type: string
| | ... | - bond_mode - Link bonding mode. Type: string
| | ... | - lb_mode - Load balance mode. Type: string
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 bridge domains with Vhost-User and VLAN with VPP\
| | ... | link bonding in a 3-node circular topology \| 1 \| 2 \| /tmp/sock1 \
| | ... | \| /tmp/sock2 \| 10 \| pop-1 \| xor \| l34 \|
| | ...
| | [Arguments] | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
| | ... | ${tag_rewrite} | ${bond_mode} | ${lb_mode}
| | ...
| | Set interfaces in path up
| | ${dut1_eth_bond_if1}= | VPP Create Bond Interface | ${dut1} | ${bond_mode}
| | ... | ${lb_mode}
| | Set Interface State | ${dut1} | ${dut1_eth_bond_if1} | up
| | VPP Set interface MTU | ${dut1} | ${dut1_eth_bond_if1}
| | ${if2_status} | ${value}= | Run Keyword And Ignore Error
| | ... | Variable Should Exist | ${dut1_if2}
| | Run Keyword If | '${if2_status}' == 'PASS'
| | ... | VPP Enslave Physical Interface | ${dut1} | ${dut1_if2}
| | ... | ${dut1_eth_bond_if1}
| | ... | ELSE
| | ... | VPP Enslave Physical Interface | ${dut1} | ${dut1_if2_1}
| | ... | ${dut1_eth_bond_if1}
| | Run Keyword Unless | '${if2_status}' == 'PASS'
| | ... | VPP Enslave Physical Interface | ${dut1} | ${dut1_if2_2}
| | ... | ${dut1_eth_bond_if1}
| | ${dut2_eth_bond_if1}= | VPP Create Bond Interface | ${dut2} | ${bond_mode}
| | ... | ${lb_mode}
| | Set Interface State | ${dut2} | ${dut2_eth_bond_if1} | up
| | VPP Set interface MTU | ${dut2} | ${dut2_eth_bond_if1}
| | ${if1_status} | ${value}= | Run Keyword And Ignore Error
| | ... | Variable Should Exist | ${dut2_if1}
| | Run Keyword If | '${if1_status}' == 'PASS'
| | ... | VPP Enslave Physical Interface | ${dut2} | ${dut2_if1}
| | ... | ${dut2_eth_bond_if1}
| | ... | ELSE
| | ... | VPP Enslave Physical Interface | ${dut2} | ${dut2_if1_1}
| | ... | ${dut2_eth_bond_if1}
| | Run Keyword Unless | '${if2_status}' == 'PASS'
| | ... | VPP Enslave Physical Interface | ${dut2} | ${dut2_if1_2}
| | ... | ${dut2_eth_bond_if1}
| | VPP Show Bond Data On All Nodes | ${nodes} | details=${TRUE}
| | Initialize VLAN dot1q sub-interfaces in 3-node circular topology
| | ... | ${dut1} | ${dut1_eth_bond_if1} | ${dut2} | ${dut2_eth_bond_if1}
| | ... | ${subid}
| | Configure L2 tag rewrite method on interfaces
| | ... | ${dut1} | ${subif_index_1} | ${dut2} | ${subif_index_2}
| | ... | ${tag_rewrite}
| | Configure vhost interfaces for L2BD forwarding | ${dut1}
| | ... | ${sock1} | ${sock2}
| | Add interface to bridge domain | ${dut1} | ${dut1_if1} | ${bd_id1}
| | Add interface to bridge domain | ${dut1} | ${vhost_if1} | ${bd_id1}
| | Add interface to bridge domain | ${dut1} | ${vhost_if2} | ${bd_id2}
| | Add interface to bridge domain | ${dut1} | ${subif_index_1} | ${bd_id2}
| | Configure vhost interfaces for L2BD forwarding | ${dut2}
| | ... | ${sock1} | ${sock2}
| | Add interface to bridge domain | ${dut2} | ${subif_index_2} | ${bd_id1}
| | Add interface to bridge domain | ${dut2} | ${vhost_if1} | ${bd_id1}
| | Add interface to bridge domain | ${dut2} | ${vhost_if2} | ${bd_id2}
| | Add interface to bridge domain | ${dut2} | ${dut2_if2} | ${bd_id2}

| Add PCI devices to all DUTs
| | [Documentation]
| | ... | Add PCI devices to VPP configuration file.
| | ...
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | ${if1_status} | ${value}= | Run Keyword And Ignore Error
| | | ... | Variable Should Exist | ${${dut}_if1}
| | | ${if1_pci}= | Run Keyword If | '${if1_status}' == 'PASS'
| | | ... | Get Interface PCI Addr | ${nodes['${dut}']} | ${${dut}_if1}
| | | ${if1_1_pci}= | Run Keyword Unless | '${if1_status}' == 'PASS'
| | | ... | Get Interface PCI Addr | ${nodes['${dut}']} | ${${dut}_if1_1}
| | | ${if1_2_pci}= | Run Keyword Unless | '${if1_status}' == 'PASS'
| | | ... | Get Interface PCI Addr | ${nodes['${dut}']} | ${${dut}_if1_2}
| | | ${if2_status} | ${value}= | Run Keyword And Ignore Error
| | | ... | Variable Should Exist | ${${dut}_if2}
| | | ${if2_pci}= | Run Keyword If | '${if2_status}' == 'PASS'
| | | ... | Get Interface PCI Addr | ${nodes['${dut}']} | ${${dut}_if2}
| | | ${if2_1_pci}= | Run Keyword Unless | '${if2_status}' == 'PASS'
| | | ... | Get Interface PCI Addr | ${nodes['${dut}']} | ${${dut}_if2_1}
| | | ${if2_2_pci}= | Run Keyword Unless | '${if2_status}' == 'PASS'
| | | ... | Get Interface PCI Addr | ${nodes['${dut}']} | ${${dut}_if2_2}
| | | @{pci_devs}= | Run Keyword If | '${if1_status}' == 'PASS'
| | | ... | Create List | ${if1_pci}
| | | ... | ELSE
| | | ... | Create List | ${if1_1_pci} | ${if1_2_pci}
| | | Run Keyword If | '${if2_status}' == 'PASS'
| | | ... | Append To List | ${pci_devs} | ${if2_pci}
| | | ... | ELSE
| | | ... | Append To List | ${pci_devs} | ${if2_1_pci} | ${if2_2_pci}
| | | Run keyword | ${dut}.Add DPDK Dev | @{pci_devs}
| | | Run Keyword If | '${if1_status}' == 'PASS'
| | | ... | Set Test Variable | ${${dut}_if1_pci} | ${if1_pci}
| | | Run Keyword Unless | '${if1_status}' == 'PASS'
| | | ... | Set Test Variable | ${${dut}_if1_1_pci} | ${if1_1_pci}
| | | Run Keyword Unless | '${if1_status}' == 'PASS'
| | | ... | Set Test Variable | ${${dut}_if1_2_pci} | ${if1_2_pci}
| | | Run Keyword If | '${if2_status}' == 'PASS'
| | | ... | Set Test Variable | ${${dut}_if2_pci} | ${if2_pci}
| | | Run Keyword Unless | '${if2_status}' == 'PASS'
| | | ... | Set Test Variable | ${${dut}_if2_1_pci} | ${if2_1_pci}
| | | Run Keyword Unless | '${if2_status}' == 'PASS'
| | | ... | Set Test Variable | ${${dut}_if2_2_pci} | ${if2_2_pci}

| Add single PCI device to all DUTs
| | [Documentation]
| | ... | Add single (first) PCI device on DUT1 and single (last) PCI device on
| | ... | DUT2 to VPP configuration file.
| | ...
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | ${if1_pci}= | Run Keyword If | '${dut}' == 'DUT1' | Get Interface PCI Addr
| | | ... | ${nodes['${dut}']} | ${${dut}_if1} | ELSE | Get Interface PCI Addr
| | | ... | ${nodes['${dut}']} | ${${dut}_if2}
| | | Run keyword | ${dut}.Add DPDK Dev | ${if1_pci}
| | | Set Test Variable | ${${dut}_if1_pci} | ${if1_pci}

| Add VLAN strip offload switch off between DUTs in 3-node single link topology
| | [Documentation]
| | ... | Add VLAN Strip Offload switch off on PCI devices between DUTs to VPP
| | ... | configuration file.
| | ...
| | Run keyword | DUT1.Add DPDK Dev Parameter | ${dut1_if2_pci}
| | ... | vlan-strip-offload | off
| | Run keyword | DUT2.Add DPDK Dev Parameter | ${dut2_if1_pci}
| | ... | vlan-strip-offload | off

| Add VLAN strip offload switch off between DUTs in 3-node double link topology
| | [Documentation]
| | ... | Add VLAN Strip Offload switch off on PCI devices between DUTs to VPP
| | ... | configuration file.
| | ...
| | Run keyword | DUT1.Add DPDK Dev Parameter | ${dut1_if2_1_pci}
| | ... | vlan-strip-offload | off
| | Run keyword | DUT1.Add DPDK Dev Parameter | ${dut1_if2_2_pci}
| | ... | vlan-strip-offload | off
| | Run keyword | DUT2.Add DPDK Dev Parameter | ${dut2_if1_1_pci}
| | ... | vlan-strip-offload | off
| | Run keyword | DUT2.Add DPDK Dev Parameter | ${dut2_if1_2_pci}
| | ... | vlan-strip-offload | off

| Add DPDK bonded ethernet interfaces to DUTs in 3-node single link topology
| | [Documentation]
| | ... | Add DPDK bonded Ethernet interfaces with mode XOR and transmit policy
| | ... | l34 to VPP configuration file.
| | ...
| | Run keyword | DUT1.Add DPDK Eth Bond Dev | 0 | 2 | l34 | ${dut1_if2_pci}
| | Run keyword | DUT2.Add DPDK Eth Bond Dev | 0 | 2 | l34 | ${dut2_if1_pci}

| Add DPDK bonded ethernet interfaces to topology file in 3-node single link topology
| | Add Eth Interface | ${dut1} | ${dut1_eth_bond_if1_name} | ifc_pfx=eth_bond
| | Add Eth Interface | ${dut2} | ${dut2_eth_bond_if1_name} | ifc_pfx=eth_bond

| Configure guest VM with dpdk-testpmd connected via vhost-user
| | [Documentation]
| | ... | Start QEMU guest with two vhost-user interfaces and interconnecting\
| | ... | DPDK testpmd.
| | ...
| | ... | *Arguments:*
| | ... | - dut - DUT node to start guest VM on. Type: dictionary
| | ... | - sock1 - Socket path for first Vhost-User interface. Type: string
| | ... | - sock2 - Socket path for second Vhost-User interface.
| | ... | Type: string
| | ... | - vm_name - QemuUtil instance name. Type: string
| | ... | - qemu_id - Qemu Id when starting more then one guest VM on DUT
| | ... | node. Type: integer
| | ... | - jumbo - Set True if jumbo frames are used in the test.
| | ... | Type: bool
| | ... | - perf_qemu_qsz - Virtio Queue Size. Type: int
| | ... | - use_tuned_cfs - Set True if CFS RR should be used for Qemu SMP.
| | ... | Type: bool
| | ...
| | ... | *Note:*
| | ... | KW uses test variables \${rxq_count_int}, \${thr_count_int} and
| | ... | \${cpu_count_int} set by "Add worker threads and rxqueues to all DUTs"
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Configure guest VM with dpdk-testpmd connected via vhost-user \
| | ... | \| ${nodes['DUT1']} \| /tmp/sock-2-1 \| /tmp/sock-2-2 \| DUT1_VM2 \
| | ... | \| qemu_id=${2} \|
| | ...
| | [Arguments] | ${dut} | ${sock1} | ${sock2} | ${vm_name} | ${qemu_id}=${1}
| | ... | ${jumbo}=${False} | ${perf_qemu_qsz}=${256}
| | ... | ${use_tuned_cfs}=${False}
| | ...
| | Import Library | resources.libraries.python.QemuUtils | qemu_id=${qemu_id}
| | ... | WITH NAME | ${vm_name}
| | Run keyword | ${vm_name}.Qemu Set Node | ${nodes['${dut}']}
| | ${serial_port}= | Evaluate | ${qemu_id} + ${4555}
| | Run keyword | ${vm_name}.Qemu Set Serial Port | ${serial_port}
| | ${ssh_fwd_port}= | Evaluate | ${qemu_id} + ${10021}
| | Run keyword | ${vm_name}.Qemu Set Ssh Fwd Port | ${ssh_fwd_port}
| | ${if1_status} | ${value}= | Run Keyword And Ignore Error
| | ... | Variable Should Exist | ${${dut}_if1}
| | @{if_list}= | Run Keyword If | '${if1_status}' == 'PASS'
| | ... | Create List | ${${dut}_if1}
| | ... | ELSE | Create List | ${${dut}_if1_1} | ${${dut}_if1_2}
| | ${if2_status} | ${value}= | Run Keyword And Ignore Error
| | ... | Variable Should Exist | ${${dut}_if2}
| | Run Keyword If | '${if2_status}' == 'PASS'
| | ... | Append To List | ${if_list} | ${${dut}_if2}
| | ... | ELSE | Append To List | ${if_list} | ${${dut}_if2_1} | ${${dut}_if2_2}
| | ${dut_numa}= | Get interfaces numa node | ${nodes['${dut}']} | @{if_list}
# Compute CPU placement for VM based on expected DUT placement.
| | ${os_cpus}= | Set Variable | ${1}
| | ${dut_main_cpus}= | Set Variable | ${1}
| | ${dut_wk_cpus}= | Set Variable | ${cpu_count_int}
| | ${vm_cpus}= | Evaluate | ${dut_wk_cpus} + ${dut_main_cpus}
| | ${skip_dut}= | Evaluate | ${dut_wk_cpus} + ${dut_main_cpus} + ${os_cpus}
| | ${skip_cpu}= | Evaluate | ${skip_dut} + (${qemu_id} - ${1}) * ${vm_cpus}
| | ${qemu_cpus}= | Cpu slice of list per node | ${nodes['${dut}']}
| | ... | ${dut_numa} | skip_cnt=${skip_cpu} | cpu_cnt=${vm_cpus}
| | ... | smt_used=${smt_used}
| | ${vm_thrs}= | Get Length | ${qemu_cpus}
| | Run keyword | ${vm_name}.Qemu Set Queue Count | ${rxq_count_int}
| | Run keyword | ${vm_name}.Qemu Set Queue Size | ${perf_qemu_qsz}
| | Run keyword | ${vm_name}.Qemu Add Vhost User If | ${sock1}
| | ... | jumbo_frames=${jumbo}
| | Run keyword | ${vm_name}.Qemu Add Vhost User If | ${sock2}
| | ... | jumbo_frames=${jumbo}
| | ${apply_patch}= | Set Variable | ${False}
| | ${perf_qemu_path}= | Set Variable If | ${apply_patch}
| | ... | ${perf_qemu_path}-patch/bin/
| | ... | ${perf_qemu_path}-base/bin/
| | Run Keyword If | ${qemu_build} | ${vm_name}.Build QEMU | ${nodes['${dut}']}
| | ... | apply_patch=${False}
| | Run keyword | ${vm_name}.Qemu Set Path | ${perf_qemu_path}
| | Run keyword | ${vm_name}.Qemu Set Smp | ${vm_thrs} | ${vm_thrs} | 1 | 1
| | Run keyword | ${vm_name}.Qemu Set Mem Size | 2048
| | Run keyword | ${vm_name}.Qemu Set Disk Image | ${perf_vm_image}
| | ${vm}= | Run keyword | ${vm_name}.Qemu Start
| | Run keyword | ${vm_name}.Qemu Set Affinity | @{qemu_cpus}
| | Run keyword If | ${use_tuned_cfs} | ${vm_name}.Qemu Set Scheduler Policy
| | ${max_pkt_len}= | Set Variable If | ${jumbo} | 9000 | ${EMPTY}
| | ${testpmd_cpus}= | Evaluate | ${thr_count_int} + ${1}
| | ${testpmd_cpus}= | Cpu list per node str | ${nodes['${dut}']} | ${0}
| | ... | cpu_cnt=${testpmd_cpus}
| | Dpdk Testpmd Start | ${vm} | eal_corelist=${testpmd_cpus}
| | ... | eal_mem_channels=4 | pmd_fwd_mode=io | pmd_disable_hw_vlan=${TRUE}
| | ... | pmd_rxd=${perf_qemu_qsz} | pmd_txd=${perf_qemu_qsz}
| | ... | pmd_rxq=${rxq_count_int} | pmd_txq=${rxq_count_int}
| | ... | pmd_max_pkt_len=${max_pkt_len}
| | Return From Keyword | ${vm}

| Configure guest VMs with dpdk-testpmd connected via vhost-user on node
| | [Documentation]
| | ... | Start ${vm_count} QEMU guests with two vhost-user interfaces and\
| | ... | interconnecting DPDK testpmd for defined number of VMs on all defined\
| | ... | VPP nodes.
| | ...
| | ... | *Arguments:*
| | ... | - dut - DUT node to start guest VM on. Type: dictionary
| | ... | - vm_count - Number of guest VMs. Type: int
| | ... | - jumbo - Jumbo frames are used (True) or are not used (False)
| | ... | in the test. Type: boolean
| | ... | - perf_qemu_qsz - Virtio Queue Size. Type: int
| | ... | - use_tuned_cfs - Set True if CFS RR should be used for Qemu SMP.
| | ... | Type: bool
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Configure guest VMs with dpdk-testpmd connected via \
| | ... | vhost-user on node \| DUT1 \| 1 \| False \| 256 \|
| | ...
| | [Arguments] | ${dut} | ${vm_count}=${1} | ${jumbo}=${False} |
| | ... | ${perf_qemu_qsz}=${256} | ${use_tuned_cfs}=${False}
| | ...
| | :FOR | ${number} | IN RANGE | 1 | ${vm_count}+1
| | | ${sock1}= | Set Variable | /tmp/sock-${number}-1
| | | ${sock2}= | Set Variable | /tmp/sock-${number}-2
| | | ${vm}=
| | | ... | Configure guest VM with dpdk-testpmd connected via vhost-user
| | | ... | ${dut} | ${sock1} | ${sock2} | ${dut}_VM${number}
| | | ... | qemu_id=${number} | jumbo=${jumbo} | perf_qemu_qsz=${perf_qemu_qsz}
| | | ... | use_tuned_cfs=${use_tuned_cfs}
| | | Set To Dictionary | ${${dut}_vm_refs} | ${dut}_VM${number} | ${vm}

| Configure guest VMs with dpdk-testpmd connected via vhost-user
| | [Documentation]
| | ... | Start ${vm_count} QEMU guests with two vhost-user interfaces and\
| | ... | interconnecting DPDK testpmd defined number of VMs on all defined VPP\
| | ... | nodes.
| | ...
| | ... | *Arguments:*
| | ... | - vm_count - Number of guest VMs. Type: int
| | ... | - jumbo - Jumbo frames are used (True) or are not used (False)
| | ... | in the test. Type: boolean
| | ... | - perf_qemu_qsz - Virtio Queue Size. Type: int
| | ... | - use_tuned_cfs - Set True if CFS RR should be used for Qemu SMP.
| | ... | Type: bool
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Configure guest VMs with dpdk-testpmd connected via vhost-user\
| | ... | \| 1 \| False \| 256 \|
| | ...
| | [Arguments] | ${vm_count}=${1} | ${jumbo}=${False} | ${perf_qemu_qsz}=${256}
| | ... | ${use_tuned_cfs}=${False}
| | ...
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | Configure guest VMs with dpdk-testpmd connected via vhost-user on node
| | | ... | ${dut} | vm_count=${vm_count} | jumbo=${jumbo}
| | | ... | perf_qemu_qsz=${perf_qemu_qsz} | use_tuned_cfs=${False}

| Configure guest VM with dpdk-testpmd-mac connected via vhost-user
| | [Documentation]
| | ... | Start QEMU guest with two vhost-user interfaces and interconnecting\
| | ... | DPDK testpmd.
| | ...
| | ... | *Arguments:*
| | ... | - dut - DUT node to start guest VM on. Type: dictionary
| | ... | - sock1 - Socket path for first Vhost-User interface.
| | ... | Type: string
| | ... | - sock2 - Socket path for second Vhost-User interface.
| | ... | Type: string
| | ... | - vm_name - QemuUtil instance name. Type: string
| | ... | - eth0_mac - MAC address of first Vhost interface. Type: string
| | ... | - eth1_mac - MAC address of second Vhost interface. Type: string
| | ... | - qemu_id - Qemu Id when starting more then one guest VM on DUT
| | ... | node. Type: integer
| | ... | - jumbo - Set True if jumbo frames are used in the test.
| | ... | Type: bool
| | ... | - perf_qemu_qsz - Virtio Queue Size. Type: int
| | ... | - use_tuned_cfs - Set True if CFS RR should be used for Qemu SMP.
| | ... | Type: bool
| | ...
| | ... | *Note:*
| | ... | KW uses test variables \${rxq_count_int}, \${thr_count_int} and
| | ... | \${cpu_count_int} set by "Add worker threads and rxqueues to all DUTs"
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Configure guest VM with dpdk-testpmd-mac connected via vhost-user \
| | ... | \| ${nodes['DUT1']} \| /tmp/sock1 \| /tmp/sock2 \| DUT1_VM \
| | ... | \| 00:00:00:00:00:01 \| 00:00:00:00:00:02 \|
| | ...
| | [Arguments] | ${dut} | ${sock1} | ${sock2} | ${vm_name}
| | ... | ${eth0_mac} | ${eth1_mac} | ${qemu_id}=${1} | ${jumbo}=${False}
| | ... | ${perf_qemu_qsz}=${256} | ${use_tuned_cfs}=${False}
| | ...
| | Import Library | resources.libraries.python.QemuUtils | qemu_id=${qemu_id}
| | ... | WITH NAME | ${vm_name}
| | Run keyword | ${vm_name}.Qemu Set Node | ${nodes['${dut}']}
| | ${serial_port}= | Evaluate | ${qemu_id} + ${4555}
| | Run keyword | ${vm_name}.Qemu Set Serial Port | ${serial_port}
| | ${ssh_fwd_port}= | Evaluate | ${qemu_id} + ${10021}
| | Run keyword | ${vm_name}.Qemu Set Ssh Fwd Port | ${ssh_fwd_port}
| | ${dut_numa}= | Get interfaces numa node | ${nodes['${dut}']}
| | ... | ${${dut}_if1} | ${${dut}_if2}
# Compute CPU placement for VM based on expected DUT placement.
| | ${os_cpus}= | Set Variable | ${1}
| | ${dut_main_cpus}= | Set Variable | ${1}
| | ${dut_wk_cpus}= | Set Variable | ${cpu_count_int}
| | ${vm_cpus}= | Evaluate | ${dut_wk_cpus} + ${dut_main_cpus}
| | ${skip_dut}= | Evaluate | ${dut_wk_cpus} + ${dut_main_cpus} + ${os_cpus}
| | ${skip_cpu}= | Evaluate | ${skip_dut} + (${qemu_id} - ${1}) * ${vm_cpus}
| | ${qemu_cpus}= | Cpu slice of list per node | ${nodes['${dut}']}
| | ... | ${dut_numa} | skip_cnt=${skip_cpu} | cpu_cnt=${vm_cpus}
| | ... | smt_used=${smt_used}
| | ${vm_thrs}= | Get Length | ${qemu_cpus}
| | Run keyword | ${vm_name}.Qemu Set Queue Count | ${rxq_count_int}
| | Run keyword | ${vm_name}.Qemu Set Queue Size | ${perf_qemu_qsz}
| | Run keyword | ${vm_name}.Qemu Add Vhost User If | ${sock1}
| | ... | jumbo_frames=${jumbo}
| | Run keyword | ${vm_name}.Qemu Add Vhost User If | ${sock2}
| | ... | jumbo_frames=${jumbo}
| | ${apply_patch}= | Set Variable | ${False}
| | ${perf_qemu_path}= | Set Variable If | ${apply_patch}
| | ... | ${perf_qemu_path}-patch/bin/
| | ... | ${perf_qemu_path}-base/bin/
| | Run Keyword If | ${qemu_build} | ${vm_name}.Build QEMU | ${nodes['${dut}']}
| | ... | apply_patch=${False}
| | Run keyword | ${vm_name}.Qemu Set Path | ${perf_qemu_path}
| | Run keyword | ${vm_name}.Qemu Set Smp | ${vm_thrs} | ${vm_thrs} | 1 | 1
| | Run keyword | ${vm_name}.Qemu Set Mem Size | 2048
| | Run keyword | ${vm_name}.Qemu Set Disk Image | ${perf_vm_image}
| | ${vm}= | Run keyword | ${vm_name}.Qemu Start
| | Run keyword | ${vm_name}.Qemu Set Affinity | @{qemu_cpus}
| | Run keyword If | ${use_tuned_cfs} | ${vm_name}.Qemu Set Scheduler Policy
| | ${max_pkt_len}= | Set Variable If | ${jumbo} | 9000 | ${EMPTY}
| | ${testpmd_cpus}= | Evaluate | ${thr_count_int} + ${1}
| | ${testpmd_cpus}= | Cpu list per node str | ${nodes['${dut}']} | ${0}
| | ... | cpu_cnt=${testpmd_cpus}
| | Dpdk Testpmd Start | ${vm} | eal_corelist=${testpmd_cpus}
| | ... | eal_mem_channels=4 | pmd_fwd_mode=mac | pmd_eth_peer_0=0,${eth0_mac}
| | ... | pmd_eth_peer_1=1,${eth1_mac} | pmd_disable_hw_vlan=${TRUE}
| | ... | pmd_rxd=${perf_qemu_qsz} | pmd_txd=${perf_qemu_qsz}
| | ... | pmd_rxq=${rxq_count_int} | pmd_txq=${rxq_count_int}
| | ... | pmd_max_pkt_len=${max_pkt_len}
| | Return From Keyword | ${vm}

| Configure guest VMs with dpdk-testpmd-mac connected via vhost-user on node
| | [Documentation]
| | ... | Start ${vm_count} QEMU guests with two vhost-user interfaces and\
| | ... | interconnecting DPDK testpmd with fwd mode set to mac rewrite for\
| | ... | defined number of VMs on all defined VPP nodes.
| | ...
| | ... | *Arguments:*
| | ... | - dut - DUT node to start guest VM on. Type: dictionary
| | ... | - vm_count} - Number of guest VMs. Type: int
| | ... | - jumbo - Jumbo frames are used (True) or are not used (False)
| | ... | in the test. Type: boolean
| | ... | - perf_qemu_qsz - Virtio Queue Size. Type: int
| | ... | - use_tuned_cfs - Set True if CFS RR should be used for Qemu SMP.
| | ... | Type: bool
| | ...
| | ... | _NOTE:_ This KW expects following test case variables to be set:
| | ... | - cpu_count_int - Number of Physical CPUs allocated for DUT.
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Configure guest VMs with dpdk-testpmd-mac connected via \
| | ... | vhost-user on node \| DUT1 \| 1 \| False \| 256 \|
| | ...
| | [Arguments] | ${dut} | ${vm_count}=${1} | ${jumbo}=${False} |
| | ... | ${perf_qemu_qsz}=${256} | ${use_tuned_cfs}=${False}
| | ...
| | :FOR | ${number} | IN RANGE | 1 | ${vm_count}+1
| | | ${sock1}= | Set Variable | /tmp/sock-${number}-1
| | | ${sock2}= | Set Variable | /tmp/sock-${number}-2
| | | ${vm}=
| | | ... | Configure guest VM with dpdk-testpmd-mac connected via vhost-user
| | | ... | ${dut} | ${sock1} | ${sock2} | ${dut}_VM${number}
| | | ... | ${${dut}-vhost-${number}-if1_mac}
| | | ... | ${${dut}-vhost-${number}-if2_mac} | qemu_id=${number}
| | | ... | jumbo=${jumbo} | perf_qemu_qsz=${perf_qemu_qsz}
| | | ... | use_tuned_cfs=${use_tuned_cfs}
| | | Set To Dictionary | ${${dut}_vm_refs} | ${dut}_VM${number} | ${vm}

| Configure guest VMs with dpdk-testpmd-mac connected via vhost-user
| | [Documentation]
| | ... | Start ${vm_count} QEMU guests with two vhost-user interfaces and\
| | ... | interconnecting DPDK testpmd with fwd mode set to mac rewrite for\
| | ... | defined number of VMs on all defined VPP nodes.
| | ...
| | ... | *Arguments:*
| | ... | - vm_count - Number of guest VMs. Type: int
| | ... | - jumbo - Jumbo frames are used (True) or are not used (False)
| | ... | in the test. Type: boolean
| | ... | - perf_qemu_qsz - Virtio Queue Size. Type: int
| | ... | - use_tuned_cfs - Set True if CFS RR should be used for Qemu SMP.
| | ... | Type: bool
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Configure guest VMs with dpdk-testpmd-mac connected via vhost-user\
| | ... | \| 1 \| False \| 256 \|
| | ...
| | [Arguments] | ${vm_count}=${1} | ${jumbo}=${False} | ${perf_qemu_qsz}=${256}
| | ... | ${use_tuned_cfs}=${False}
| | ...
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | Configure guest VMs with dpdk-testpmd-mac connected via vhost-user on node
| | | ... | ${dut} | vm_count=${vm_count} | jumbo=${jumbo}
| | | ... | perf_qemu_qsz=${perf_qemu_qsz} | use_tuned_cfs=${False}

| Configure guest VM with linux bridge connected via vhost-user
| | [Documentation]
| | ... | Start QEMU guest with two vhost-user interfaces and interconnecting\
| | ... | linux bridge.
| | ...
| | ... | *Arguments:*
| | ... | - dut - DUT node to start guest VM on. Type: dictionary
| | ... | - sock1 - Socket path for first Vhost-User interface.
| | ... | Type: string
| | ... | - sock2 - Socket path for second Vhost-User interface.
| | ... | Type: string
| | ... | - vm_name - QemuUtil instance name. Type: string
| | ... | - skip_cnt - number of cpus which will be skipped. Type: int
| | ...
| | ... | _NOTE:_ This KW expects following test case variables to be set:
| | ... | - cpu_count_int - Number of Physical CPUs allocated for DUT.
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Configure guest VM with linux bridge connected via vhost-user \
| | ... | \| ${nodes['DUT1']} \| /tmp/sock1 \| /tmp/sock2 \| DUT1_VM \| ${6} \|
| | ...
| | [Arguments] | ${dut} | ${sock1} | ${sock2} | ${vm_name} | ${skip_cnt}=${6}
| | ... | ${count}=${5}
| | ...
| | Import Library | resources.libraries.python.QemuUtils
| | ... | WITH NAME | ${vm_name}
| | Run keyword | ${vm_name}.Qemu Set Node | ${dut}
| | ${dut_numa}= | Get interfaces numa node | ${dut}
| | ... | ${dut1_if1} | ${dut1_if2}
| | ${vm_phy_cpus}= | Evaluate | ${cpu_count_int} + ${1}
| | ${skip_cnt}= | Evaluate | ${skip} + (${qemu_id} - ${1}) * ${vm_phy_cpus}
| | ${qemu_cpus}= | Cpu slice of list per node | ${dut} | ${dut_numa}
| | ... | skip_cnt=${skip_cnt} | cpu_cnt=${vm_phy_cpus} | smt_used=${smt_used}
| | ${vm_thr_cpus}= | Get Length | ${qemu_cpus}
| | Run keyword | ${vm_name}.Qemu Set Queue Size | ${perf_qemu_qsz}
| | Run keyword | ${vm_name}.Qemu Add Vhost User If | ${sock1}
| | Run keyword | ${vm_name}.Qemu Add Vhost User If | ${sock2}
| | ${apply_patch}= | Set Variable | ${False}
| | ${perf_qemu_path}= | Set Variable If | ${apply_patch}
| | ... | ${perf_qemu_path}-patch/bin/
| | ... | ${perf_qemu_path}-base/bin/
| | Run Keyword If | ${qemu_build} | ${vm_name}.Build QEMU | ${dut}
| | ... | apply_patch=${apply_patch}
| | Run keyword | ${vm_name}.Qemu Set Path | ${perf_qemu_path}
| | Run keyword | ${vm_name}.Qemu Set Smp | ${vm_thr_cpus} | ${vm_thr_cpus}
| | ... | 1 | 1
| | Run keyword | ${vm_name}.Qemu Set Mem Size | 2048
| | Run keyword | ${vm_name}.Qemu Set Disk Image | ${perf_vm_image}
| | ${vm}= | Run keyword | ${vm_name}.Qemu Start
| | Run keyword | ${vm_name}.Qemu Set Affinity | @{qemu_cpus}
| | ${br}= | Set Variable | br0
| | ${vhost1}= | Get Vhost User If Name By Sock | ${vm} | ${sock1}
| | ${vhost2}= | Get Vhost User If Name By Sock | ${vm} | ${sock2}
| | Linux Add Bridge | ${vm} | ${br} | ${vhost1} | ${vhost2}
| | Set Interface State | ${vm} | ${vhost1} | up | if_type=name
| | Set Interface State | ${vm} | ${vhost2} | up | if_type=name
| | Set Interface State | ${vm} | ${br} | up | if_type=name
| | Return From Keyword | ${vm}

| Initialize LISP IPv4 forwarding in 3-node circular topology
| | [Documentation] | Custom setup of IPv4 addresses on all DUT nodes and TG \
| | ... | Don`t set route.
| | ...
| | ... | *Arguments:*
| | ... | -${dut1_dut2_address} - Ip address from DUT1 to DUT2. Type: string
| | ... | -${dut1_tg_address} - Ip address from DUT1 to tg. Type: string
| | ... | -${dut2_dut1_address} - Ip address from DUT2 to DUT1. Type: string
| | ... | -${dut1_tg_address} - Ip address from DUT1 to tg. Type: string
| | ... | -${duts_prefix} - ip prefix. Type: int
| | ...
| | ... | *Return:*
| | ... | - No value returned
| | ...
| | ... | *Example:*
| | ... | \| Initialize LISP IPv4 forwarding in 3-node circular topology \
| | ... | \| ${dut1_dut2_address} \| ${dut1_tg_address} \
| | ... | \| ${dut2_dut1_address} \| ${dut2_tg_address} \| ${duts_prefix} \|
| | ...
| | [Arguments] | ${dut1_dut2_address} | ${dut1_tg_address}
| | ... | ${dut2_dut1_address} | ${dut2_tg_address} | ${duts_prefix}
| | ...
| | Set interfaces in path up
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
| | Add arp on dut | ${dut1} | ${dut1_if1} | 10.10.10.2 | ${tg1_if1_mac}
| | Add arp on dut | ${dut1} | ${dut1_if2} | ${dut2_dut1_address}
| | ... | ${dut2_if1_mac}
| | Add arp on dut | ${dut2} | ${dut2_if1} | ${dut1_dut2_address}
| | ... | ${dut1_if2_mac}
| | Add arp on dut | ${dut2} | ${dut2_if2} | 20.20.20.2 | ${tg1_if2_mac}
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if1}
| | ... | ${dut1_tg_address} | ${duts_prefix}
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2}
| | ... | ${dut1_dut2_address} | ${duts_prefix}
| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if1}
| | ... | ${dut2_dut1_address} | ${duts_prefix}
| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if2}
| | ... | ${dut2_tg_address} | ${duts_prefix}

| Initialize LISP GPE IPv4 over IPsec in 3-node circular topology
| | [Documentation] | Setup Lisp GPE IPv4 forwarding over IPsec.
| | ...
| | ... | *Arguments:*
| | ... | -${encr_alg} - Encryption algorithm. Type: string
| | ... | -${auth_alg} - Authentication algorithm. Type: string
| | ...
| | ... | *Return:*
| | ... | - No value returned
| | ...
| | ... | *Example:*
| | ... | \| Initialize LISP GPE IPv4 over IPsec in 3-node circular topology\
| | ... | \| ${encr_alg} \| ${auth_alg}
| | ...
| | [Arguments] | ${encr_alg} | ${auth_alg}
| | ...
| | Generate keys for IPSec | ${encr_alg} | ${auth_alg}
| | Initialize LISP IPv4 forwarding in 3-node circular topology
| | ... | ${dut1_to_dut2_ip4} | ${dut1_to_tg_ip4} | ${dut2_to_dut1_ip4}
| | ... | ${dut2_to_tg_ip4} | ${prefix4}
| | Configure LISP GPE topology in 3-node circular topology
| | ... | ${dut1} | ${dut1_if2} | ${NONE}
| | ... | ${dut2} | ${dut2_if1} | ${NONE}
| | ... | ${duts_locator_set} | ${dut1_ip4_eid} | ${dut2_ip4_eid}
| | ... | ${dut1_ip4_static_adjacency} | ${dut2_ip4_static_adjacency}
| | Configure manual keyed connection for IPSec
| | ... | ${dut1} | ${dut1_if2} | ${encr_alg} | ${encr_key}
| | ... | ${auth_alg} | ${auth_key} | ${dut1_spi} | ${dut2_spi}
| | ... | ${dut1_to_dut2_ip4} | ${dut2_to_dut1_ip4}
| | Configure manual keyed connection for IPSec
| | ... | ${dut2} | ${dut2_if1} | ${encr_alg} | ${encr_key}
| | ... | ${auth_alg} | ${auth_key} | ${dut2_spi} | ${dut1_spi}
| | ... | ${dut2_to_dut1_ip4} | ${dut1_to_dut2_ip4}

| Initialize LISP IPv6 forwarding in 3-node circular topology
| | [Documentation] | Custom setup of IPv6 topology on all DUT nodes \
| | ... | Don`t set route.
| | ...
| | ... | *Arguments:*
| | ... | -${dut1_dut2_address} - Ip address from DUT1 to DUT2. Type: string
| | ... | -${dut1_tg_address} - Ip address from DUT1 to tg. Type: string
| | ... | -${dut2_dut1_address} - Ip address from DUT2 to DUT1. Type: string
| | ... | -${dut1_tg_address} - Ip address from DUT1 to tg. Type: string
| | ... | -${duts_prefix} - ip prefix. Type: int
| | ...
| | ... | *Return:*
| | ... | - No value returned
| | ...
| | ... | *Example:*
| | ... | \| Initialize LISP IPv6 forwarding in 3-node circular topology \
| | ... | \| ${dut1_dut2_address} \| ${dut1_tg_address} \
| | ... | \| ${dut2_dut1_address} \| ${dut2_tg_address} \| ${duts_prefix} \|
| | ...
| | [Arguments] | ${dut1_dut2_address} | ${dut1_tg_address}
| | ... | ${dut2_dut1_address} | ${dut2_tg_address} | ${prefix}
| | ...
| | Set interfaces in path up
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if1} | ${dut1_tg_address}
| | ... | ${prefix}
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if2} | ${dut1_dut2_address}
| | ... | ${prefix}
| | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if1} | ${dut2_dut1_address}
| | ... | ${prefix}
| | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if2} | ${dut2_tg_address}
| | ... | ${prefix}
| | Suppress ICMPv6 router advertisement message | ${nodes}
| | Add Ip Neighbor | ${dut1} | ${dut1_if1} | 2001:1::2 | ${tg1_if1_mac}
| | Add Ip Neighbor | ${dut2} | ${dut2_if2} | 2001:2::2 | ${tg1_if2_mac}
| | Add Ip Neighbor | ${dut1} | ${dut1_if2} | ${dut2_dut1_address}
| | ... | ${dut2_if1_mac}
| | Add Ip Neighbor | ${dut2} | ${dut2_if1} | ${dut1_dut2_address}
| | ... | ${dut1_if2_mac}

| Initialize LISP IPv4 over IPv6 forwarding in 3-node circular topology
| | [Documentation] | Custom setup of IPv4 over IPv6 topology on all DUT nodes \
| | ... | Don`t set route.
| | ...
| | ... | *Arguments:*
| | ... | - ${dut1_dut2_ip6_address} - IPv6 address from DUT1 to DUT2.
| | ... | Type: string
| | ... | - ${dut1_tg_ip4_address} - IPv4 address from DUT1 to tg. Type: string
| | ... | - ${dut2_dut1_ip6_address} - IPv6 address from DUT2 to DUT1.
| | ... | Type: string
| | ... | - ${dut1_tg_ip4_address} - IPv4 address from DUT1 to tg. Type: string
| | ... | - ${prefix4} - IPv4 prefix. Type: int
| | ... | - ${prefix6} - IPv6 prefix. Type: int
| | ...
| | ... | *Return:*
| | ... | - No value returned
| | ...
| | ... | *Example:*
| | ... | \| Lisp IPv4 over IPv6 forwarding initialized in a 3-node circular \
| | ... | topology \| ${dut1_dut2_ip6_address} \| ${dut1_tg_ip4_address} \
| | ... | \| ${dut2_dut1_ip6_address} \| ${dut2_tg_ip4_address} \
| | ... | \| ${prefix4} \| ${prefix6} \|
| | ...
| | [Arguments] | ${dut1_dut2_ip6_address} | ${dut1_tg_ip4_address}
| | ... | ${dut2_dut1_ip6_address} | ${dut2_tg_ip4_address}
| | ... | ${prefix4} | ${prefix6}
| | ...
| | Set interfaces in path up
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if1}
| | ... | ${dut1_tg_ip4_address} | ${prefix4}
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if2} | ${dut1_dut2_ip6_address}
| | ... | ${prefix6}
| | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if1} | ${dut2_dut1_ip6_address}
| | ... | ${prefix6}
| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if2}
| | ... | ${dut2_tg_ip4_address} | ${prefix4}
| | Suppress ICMPv6 router advertisement message | ${nodes}
| | Add arp on dut | ${dut1} | ${dut1_if1} | 10.10.10.2 | ${tg1_if1_mac}
| | Add arp on dut | ${dut2} | ${dut2_if2} | 20.20.20.2 | ${tg1_if2_mac}
| | Add Ip Neighbor | ${dut1} | ${dut1_if2} | ${dut2_dut1_ip6_address}
| | ... | ${dut2_if1_mac}
| | Add Ip Neighbor | ${dut2} | ${dut2_if1} | ${dut1_dut2_ip6_address}
| | ... | ${dut1_if2_mac}

| Initialize LISP IPv6 over IPv4 forwarding in 3-node circular topology
| | [Documentation] | Custom setup of IPv4 over IPv6 topology on all DUT nodes \
| | ... | Don`t set route.
| | ...
| | ... | *Arguments:*
| | ... | - ${dut1_dut2_ip4_address} - IPv4 address from DUT1 to DUT2.
| | ... | Type: string
| | ... | - ${dut1_tg_ip6_address} - IPv6 address from DUT1 to tg. Type: string
| | ... | - ${dut2_dut1_ip4_address} - IPv4 address from DUT2 to DUT1.
| | ... | Type: string
| | ... | - ${dut1_tg_ip6_address} - IPv6 address from DUT1 to tg. Type: string
| | ... | - ${prefix4} - IPv4 prefix. Type: int
| | ... | - ${prefix6} - IPv6 prefix. Type: int
| | ...
| | ... | *Return:*
| | ... | - No value returned
| | ...
| | ... | *Example:*
| | ... | \| Lisp IPv6 over IPv4 forwarding initialized in a 3-node circular \
| | ... | topology \| ${dut1_dut2_ip4_address} \| ${dut1_tg_ip6_address} \
| | ... | \| ${dut2_dut1_ip4_address} \| ${dut2_tg_ip6_address} \
| | ... | \| ${prefix6} \| ${prefix4} \|
| | ...
| | [Arguments] | ${dut1_dut2_ip4_address} | ${dut1_tg_ip6_address}
| | ... | ${dut2_dut1_ip4_address} | ${dut2_tg_ip6_address}
| | ... | ${prefix6} | ${prefix4}
| | ...
| | Set interfaces in path up
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
| | VPP Set If IPv6 Addr | ${dut1} | ${dut1_if1} | ${dut1_tg_ip6_address}
| | ... | ${prefix6}
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2}
| | ... | ${dut1_dut2_ip4_address} | ${prefix4}
| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if1}
| | ... | ${dut2_dut1_ip4_address} | ${prefix4}
| | VPP Set If IPv6 Addr | ${dut2} | ${dut2_if2} | ${dut2_tg_ip6_address}
| | ... | ${prefix6}
| | Suppress ICMPv6 router advertisement message | ${nodes}
| | Add Ip Neighbor | ${dut1} | ${dut1_if1} | 2001:1::2 | ${tg1_if1_mac}
| | Add Ip Neighbor | ${dut2} | ${dut2_if2} | 2001:2::2 | ${tg1_if2_mac}
| | Add arp on dut | ${dut1} | ${dut1_if2} | ${dut2_dut1_ip4_address}
| | ... | ${dut2_if1_mac}
| | Add arp on dut | ${dut2} | ${dut2_if1} | ${dut1_dut2_ip4_address}
| | ... | ${dut1_if2_mac}

| Initialize NAT44 in circular topology
| | [Documentation] | Initialization of 2-node / 3-node topology with NAT44
| | ... | between DUTs:
| | ... | - set interfaces up
| | ... | - set IP addresses
| | ... | - set ARP
| | ... | - create routes
| | ... | - set NAT44 - only on DUT1
| | ...
| | ${dut2_status} | ${value}= | Run Keyword And Ignore Error
| | ... | Variable Should Exist | ${dut2}
| | ...
| | Set interfaces in path up
| | ...
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if1} | 10.0.0.1 | 20
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2} | 11.0.0.1 | 20
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Configure IP addresses on interfaces | ${dut2} | ${dut2_if1} | 11.0.0.2 | 20
| | ${dut}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Set Variable | ${dut2}
| | ... | ELSE | Set Variable | ${dut1}
| | ${dut_if2}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Set Variable | ${dut2_if2}
| | ... | ELSE | Set Variable | ${dut1_if2}
| | Configure IP addresses on interfaces | ${dut} | ${dut_if2} | 12.0.0.1 | 20
| | ...
| | ${tg_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
| | ${dut1_if2_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Get Interface MAC | ${dut1} | ${dut1_if2}
| | ${dut2_if1_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Get Interface MAC | ${dut2} | ${dut2_if1}
| | ...
| | Add arp on dut | ${dut1} | ${dut1_if1} | 10.0.0.2 | ${tg_if1_mac}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Add arp on dut | ${dut1} | ${dut1_if2} | 11.0.0.2 | ${dut2_if1_mac}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Add arp on dut | ${dut2} | ${dut2_if1} | 11.0.0.1 | ${dut1_if2_mac}
| | Add arp on dut | ${dut} | ${dut_if2} | 12.0.0.2 | ${tg_if2_mac}
| | ...
| | Vpp Route Add | ${dut1} | 20.0.0.0 | 18 | 10.0.0.2 | ${dut1_if1}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Vpp Route Add | ${dut1} | 12.0.0.2 | 32 | 11.0.0.2 | ${dut1_if2}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Vpp Route Add | ${dut2} | 12.0.0.0 | 24 | 12.0.0.2 | ${dut2_if2}
| | Run Keyword If | '${dut2_status}' == 'PASS'
| | ... | Vpp Route Add | ${dut2} | 200.0.0.0 | 30 | 11.0.0.1 | ${dut2_if1}
| | ...
| | Configure inside and outside interfaces
| | ... | ${dut1} | ${dut1_if1} | ${dut1_if2}
| | Configure deterministic mode for NAT44
| | ... | ${dut1} | 20.0.0.0 | 18 | 200.0.0.0 | 30

| Initialize L2 xconnect with memif pairs on DUT node
| | [Documentation]
| | ... | Create pairs of Memif interfaces on DUT node. Cross connect each Memif
| | ... | interface with one physical interface or virtual interface to create
| | ... | a chain accross DUT node.
| | ...
| | ... | *Arguments:*
| | ... | - ${dut} - DUT node. Type: dictionary
| | ... | - ${count} - Number of memif pairs (containers). Type: integer
| | ...
| | ... | *Note:*
| | ... | Socket paths for Memif are defined in following format:
| | ... | - /tmp/memif-${dut}_VNF${number}-${sid}
| | ...
| | ... | KW uses test variable ${rxq_count_int} set by KW Add worker threads
| | ... | and rxqueues to all DUTs
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 xconnect with memif pairs on DUT node \| ${dut} \
| | ... | \| ${1} \|
| | ...
| | [Arguments] | ${dut} | ${count}
| | ...
| | :FOR | ${number} | IN RANGE | 1 | ${count}+1
| | | ${sock1}= | Set Variable | memif-${dut}_VNF
| | | ${sock2}= | Set Variable | memif-${dut}_VNF
| | | ${prev_index}= | Evaluate | ${number}-1
| | | Set up memif interfaces on DUT node | ${nodes['${dut}']}
| | | ... | ${sock1} | ${sock2} | ${number} | ${dut}-memif-${number}-if1
| | | ... | ${dut}-memif-${number}-if2 | ${rxq_count_int} | ${rxq_count_int}
| | | ${xconnect_if1}= | Set Variable If | ${number}==1 | ${${dut}_if1}
| | | ... | ${${dut}-memif-${prev_index}-if2}
| | | Configure L2XC | ${nodes['${dut}']} | ${xconnect_if1}
| | | ... | ${${dut}-memif-${number}-if1}
| | | Run Keyword If | ${number}==${count} | Configure L2XC
| | | ... | ${nodes['${dut}']} | ${${dut}-memif-${number}-if2} | ${${dut}_if2}

| Initialize L2 xconnect with memif pairs
| | [Documentation]
| | ... | Create pairs of Memif interfaces on all defined VPP nodes. Cross
| | ... | connect each Memif interface with one physical interface or virtual
| | ... | interface to create a chain accross DUT node.
| | ...
| | ... | *Arguments:*
| | ... | - ${count} - Number of memif pairs (containers). Type: integer
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 xconnect with memif pairs \| ${1} \|
| | ...
| | [Arguments] | ${count}=${1}
| | ...
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | Initialize L2 xconnect with memif pairs on DUT node | ${dut} | ${count}
| | Set interfaces in path up
| | Show Memif on all DUTs | ${nodes}

| Initialize L2 Bridge Domain with memif pairs on DUT node
| | [Documentation]
| | ... | Create pairs of Memif interfaces on DUT node. Put each Memif interface
| | ... | to separate L2 bridge domain with one physical or virtual interface
| | ... | to create a chain accross DUT node.
| | ...
| | ... | *Arguments:*
| | ... | - ${dut} - DUT node. Type: dictionary
| | ... | - ${count} - Number of memif pairs (containers). Type: integer
| | ...
| | ... | *Note:*
| | ... | Socket paths for Memif are defined in following format:
| | ... | - /tmp/memif-${dut}_VNF${number}-${sid}
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 Bridge Domain with memif pairs on DUT node \
| | ... | \| ${dut} \| ${1} \|
| | ...
| | [Arguments] | ${dut} | ${count}
| | ...
| | ${bd_id2}= | Evaluate | ${count}+1
| | Add interface to bridge domain | ${nodes['${dut}']} | ${${dut}_if1} | ${1}
| | Add interface to bridge domain | ${nodes['${dut}']} | ${${dut}_if2}
| | ... | ${bd_id2}
| | :FOR | ${number} | IN RANGE | 1 | ${count}+1
| | | ${sock1}= | Set Variable | memif-${dut}_VNF
| | | ${sock2}= | Set Variable | memif-${dut}_VNF
| | | Set up memif interfaces on DUT node | ${nodes['${dut}']}
| | | ... | ${sock1} | ${sock2} | ${number} | ${dut}-memif-${number}-if1
| | | ... | ${dut}-memif-${number}-if2 | ${rxq_count_int} | ${rxq_count_int}
| | | ${bd_id2}= | Evaluate | ${number}+1
| | | Add interface to bridge domain | ${nodes['${dut}']}
| | | ... | ${${dut}-memif-${number}-if1} | ${number}
| | | Add interface to bridge domain | ${nodes['${dut}']}
| | | ... | ${${dut}-memif-${number}-if2} | ${bd_id2}

| Initialize L2 Bridge Domain with memif pairs
| | [Documentation]
| | ... | Create pairs of Memif interfaces on all defined VPP nodes. Put each
| | ... | Memif interface to separate L2 bridge domain with one physical or
| | ... | virtual interface to create a chain accross DUT node.
| | ...
| | ... | *Arguments:*
| | ... | - ${count} - Number of memif pairs (containers). Type: integer
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 Bridge Domain with memif pairs \| ${1} \|
| | ...
| | [Arguments] | ${count}=${1}
| | ...
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | Initialize L2 Bridge Domain with memif pairs on DUT node | ${dut}
| | | ... | ${count}
| | Set interfaces in path up
| | Show Memif on all DUTs | ${nodes}

| Initialize IPv4 routing with memif pairs on DUT node
| | [Documentation]
| | ... | Create pairs of Memif interfaces on DUT node. Put each Memif interface
| | ... | to separate IPv4 VRF with one physical or virtual interface
| | ... | to create a chain accross DUT node.
| | ...
| | ... | *Arguments:*
| | ... | - ${dut} - DUT node. Type: dictionary
| | ... | - ${count} - Number of memif pairs (containers). Type: integer
| | ...
| | ... | *Note:*
| | ... | Socket paths for Memif are defined in following format:
| | ... | - /tmp/memif-${dut}_VNF${number}-${sid}
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize IPv4 routing with memif pairs on DUT node \
| | ... | \| ${dut} \| ${1} \|
| | ...
| | [Arguments] | ${dut} | ${count}
| | ...
| | @{duts}= | Get Matches | ${nodes} | DUT*
| | ${dut_index}= | Get Index From List | ${duts} | ${dut}
| | ${duts_length}= | Get Length | ${duts}
| | ${last_dut_index}= | Evaluate | ${duts_length} - ${1}
| | ...
| | ${tg_if1_net}= | Set Variable | 10.10.10.0
| | ${tg_if2_net}= | Set Variable | 20.20.20.0
| | ...
| | ${fib_table_1}= | Set Variable | ${10}
| | Run Keyword If | ${fib_table_1} > ${0}
| | ... | Add Fib Table | ${nodes['${dut}']} | ${fib_table_1}
| | ${ip_base_if1}= | Evaluate | ${dut_index} + ${1}
| | ${ip_net_if1}= | Set Variable
| | ... | ${ip_base_if1}.${ip_base_if1}.${ip_base_if1}
| | Vpp Route Add | ${nodes['${dut}']} | ${tg_if1_net} | 24 | vrf=${fib_table_1}
| | ... | gateway=${ip_net_if1}.1 | interface=${${dut}_if1} | multipath=${TRUE}
| | Assign Interface To Fib Table | ${nodes['${dut}']} | ${${dut}_if1}
| | ... | ${fib_table_1}
| | Configure IP addresses on interfaces | ${nodes['${dut}']} | ${${dut}_if1}
| | ... | ${ip_net_if1}.2 | 30
| | ${prev_node}= | Run Keyword If | ${dut_index} == ${0}
| | ... | Set Variable | TG
| | ... | ELSE | Get From List | ${duts} | ${dut_index-${1}}
| | ${prev_if}= | Run Keyword If | ${dut_index} == ${0}
| | ... | Set Variable | if1
| | ... | ELSE | Set Variable | if2
| | ${prev_if_mac}= | Get Interface MAC | ${nodes['${prev_node}']}
| | ... | ${${prev_node}_${prev_if}}
| | Add ARP on DUT | ${nodes['${dut}']} | ${${dut}_if1} | ${ip_net_if1}.1
| | ... | ${prev_if_mac}
| | ...
| | ${fib_table_2}= | Evaluate | ${fib_table_1} + ${count}
| | Add Fib Table | ${nodes['${dut}']} | ${fib_table_2}
| | ${ip_base_if2}= | Evaluate | ${ip_base_if1} + ${1}
| | ${ip_net_if2}= | Set Variable
| | ... | ${ip_base_if2}.${ip_base_if2}.${ip_base_if2}
| | Vpp Route Add | ${nodes['${dut}']} | ${tg_if2_net} | 24 | vrf=${fib_table_2}
| | ... | gateway=${ip_net_if2}.2 | interface=${${dut}_if2} | multipath=${TRUE}
| | Assign Interface To Fib Table | ${nodes['${dut}']} | ${${dut}_if2}
| | ... | ${fib_table_2}
| | Configure IP addresses on interfaces | ${nodes['${dut}']} | ${${dut}_if2}
| | ... | ${ip_net_if2}.1 | 30
| | ${next_node}= | Run Keyword If | ${dut_index} == ${last_dut_index}
| | ... | Set Variable | TG
| | ... | ELSE | Get From List | ${duts} | ${dut_index+${1}}
| | ${next_if}= | Run Keyword If | ${dut_index} == ${last_dut_index}
| | ... | Set Variable | if2
| | ... | ELSE | Set Variable | if1
| | ${next_if_mac}= | Get Interface MAC | ${nodes['${next_node}']}
| | ... | ${${next_node}_${next_if}}
| | Add ARP on DUT | ${nodes['${dut}']} | ${${dut}_if2} | ${ip_net_if2}.2
| | ... | ${next_if_mac}
| | ...
| | ${fib_table_1}= | Evaluate | ${fib_table_1} - ${1}
| | ${ip_base_start}= | Set Variable | ${31}
| | :FOR | ${number} | IN RANGE | 1 | ${count+${1}}
| | | ${sock1}= | Set Variable | memif-${dut}_VNF
| | | ${sock2}= | Set Variable | memif-${dut}_VNF
| | | Set up memif interfaces on DUT node | ${nodes['${dut}']}
| | | ... | ${sock1} | ${sock2} | ${number} | ${dut}-memif-${number}-if1
| | | ... | ${dut}-memif-${number}-if2 | ${rxq_count_int} | ${rxq_count_int}
| | | ${memif1}= | Set Variable | ${${dut}-memif-${number}-if1}
| | | ${memif2}= | Set Variable | ${${dut}-memif-${number}-if2}
| | | ${fib_table_1}= | Evaluate | ${fib_table_1} + ${1}
| | | ${fib_table_2}= | Evaluate | ${fib_table_1} + ${1}
| | | Run Keyword Unless | ${number} == ${count}
| | | ... | Add Fib Table | ${nodes['${dut}']} | ${fib_table_2}
| | | Assign Interface To Fib Table | ${nodes['${dut}']}
| | | ... | ${memif1} | ${fib_table_1}
| | | Assign Interface To Fib Table | ${nodes['${dut}']}
| | | ... | ${memif2} | ${fib_table_2}
| | | ${ip_base_memif1}= | Evaluate
| | | ... | ${ip_base_start} + (${number} - ${1}) * ${2}
| | | ${ip_base_memif2}= | Evaluate | ${ip_base_memif1} + ${1}
| | | ${ip_net_memif1}= | Set Variable
| | | ... | ${ip_base_memif1}.${ip_base_memif1}.${ip_base_memif1}
| | | ${ip_net_memif2}= | Set Variable
| | | ... | ${ip_base_memif2}.${ip_base_memif2}.${ip_base_memif2}
| | | Configure IP addresses on interfaces
| | | ... | ${nodes['${dut}']} | ${memif1} | ${ip_net_memif1}.1 | 30
| | | ... | ${nodes['${dut}']} | ${memif2} | ${ip_net_memif2}.1 | 30
| | | Vpp Route Add | ${nodes['${dut}']} | ${tg_if2_net} | 24
| | | ... | vrf=${fib_table_1} | gateway=${ip_net_memif2}.1
| | | ... | interface=${memif1}
| | | Vpp Route Add | ${nodes['${dut}']} | ${tg_if1_net} | 24
| | | ... | vrf=${fib_table_2} | gateway=${ip_net_memif1}.1
| | | ... | interface=${memif2}
| | | ${memif_if1_key}= | Get interface by sw index | ${nodes['${dut}']}
| | | ... | ${memif1}
| | | ${memif_if1_mac}= | Get interface mac | ${nodes['${dut}']}
| | | ... | ${memif_if1_key}
| | | ${memif_if2_key}= | Get interface by sw index | ${nodes['${dut}']}
| | | ... | ${memif2}
| | | ${memif_if2_mac}= | Get interface mac | ${nodes['${dut}']}
| | | ... | ${memif_if2_key}
| | | Add arp on dut | ${nodes['${dut}']} | ${memif1} | ${ip_net_memif2}.1
| | | ... | ${memif_if2_mac}
| | | Add arp on dut | ${nodes['${dut}']} | ${memif2} | ${ip_net_memif1}.1
| | | ... | ${memif_if1_mac}

| Initialize IPv4 routing with memif pairs
| | [Documentation]
| | ... | Create pairs of Memif interfaces on all defined VPP nodes. Put each
| | ... | Memif interface to separate IPv4 VRF with one physical or
| | ... | virtual interface to create a chain accross DUT node.
| | ...
| | ... | *Arguments:*
| | ... | - ${count} - Number of memif pairs (containers). Type: integer
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize IPv4 routing with memif pairs \| ${1} \|
| | ...
| | [Arguments] | ${count}=${1}
| | ...
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | Initialize IPv4 routing with memif pairs on DUT node | ${dut} | ${count}
| | Set interfaces in path up
| | Show Memif on all DUTs | ${nodes}

| Initialize L2 xconnect for single memif
| | [Documentation]
| | ... | Create single Memif interface on all defined VPP nodes. Cross
| | ... | connect Memif interface with one physical interface.
| | ...
| | ... | *Arguments:*
| | ... | - ${number} - Memif ID. Type: integer
| | ...
| | ... | *Note:*
| | ... | Socket paths for Memif are defined in following format:
| | ... | - /tmp/memif-DUT1_VNF${number}-${sid}
| | ...
| | ... | KW uses test variable ${rxq_count_int} set by KW Add worker threads
| | ... | and rxqueues to all DUTs
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 xconnect for single memif \| 1 \|
| | ...
| | [Arguments] | ${number}=${1}
| | ...
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | ${sock}= | Set Variable | memif-${dut}_VNF
| | | Set up single memif interface on DUT node | ${nodes['${dut}']} | ${sock}
| | | ... | ${number} | ${dut}-memif-${number}-if1 | ${rxq_count_int}
| | | ... | ${rxq_count_int}
| | | Configure L2XC | ${nodes['${dut}']} | ${${dut}_if1}
| | | ... | ${${dut}-memif-${number}-if1}
| | Set interfaces in path up
| | Show Memif on all DUTs | ${nodes}

| Initialize L2 Bridge Domain for single memif
| | [Documentation]
| | ... | Create single Memif interface on all defined VPP nodes. Put Memif
| | ... | interface to separate L2 bridge domain with one physical interface.
| | ...
| | ... | *Arguments:*
| | ... | - ${number} - Memif ID. Type: integer
| | ...
| | ... | *Note:*
| | ... | Socket paths for Memif are defined in following format:
| | ... | - /tmp/memif-DUT1_VNF${number}-${sid}
| | ...
| | ... | KW uses test variable ${rxq_count_int} set by KW Add worker threads
| | ... | and rxqueues to all DUTs
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Initialize L2 Bridge Domain for single memif \| 1 \|
| | ...
| | [Arguments] | ${number}=${1}
| | ...
| | ${duts}= | Get Matches | ${nodes} | DUT*
| | :FOR | ${dut} | IN | @{duts}
| | | ${sock}= | Set Variable | memif-${dut}_VNF
| | | Set up single memif interface on DUT node | ${nodes['${dut}']} | ${sock}
| | | ... | ${number} | ${dut}-memif-${number}-if1 | ${rxq_count_int}
| | | ... | ${rxq_count_int}
| | | Add interface to bridge domain | ${nodes['${dut}']} | ${${dut}_if1}
| | | ... | ${number}
| | | Add interface to bridge domain | ${nodes['${dut}']}
| | | ... | ${${dut}-memif-${number}-if1} | ${number}
| | Set interfaces in path up
| | Show Memif on all DUTs | ${nodes}

| Configure ACLs on a single interface
| | [Documentation]
| | ... | Configure ACL
| | ...
| | ... | *Arguments:*
| | ... | - dut - DUT node. Type: string
| | ... | - dut_if - DUT node interface name. Type: string
| | ... | - acl_apply_type - To what path apply the ACL - input or output.
| | ... | - acl_action - Action for the rule - deny, permit, permit+reflect.
| | ... | - subnets - Subnets to apply the specific ACL. Type: list
| | ...
| | ... | *Example:*
| | ...
| | ... | \| Configure ACLs on a single interface \| ${nodes['DUT1']}
| | ... | \| ... \| GigabitEthernet0/7/0 \| input \| permit | 0.0.0.0/0
| | ...
| | [Arguments] | ${dut} | ${dut_if} | ${acl_apply_type} | ${acl_action}
| | ... | @{subnets}
| | Set Test variable | ${acl} | ${EMPTY}
| | :FOR | ${subnet} | IN | @{subnets}
| | | ${acl} = | Run Keyword If | '${acl}' == '${EMPTY}'
| | | ... | Set Variable | ipv4 ${acl_action} src ${subnet}
| | | ... | ELSE
| | | ... | Catenate | SEPARATOR=, | ${acl}
| | | ... | ipv4 ${acl_action} src ${subnet}
| | Add Replace Acl Multi Entries | ${dut} | rules=${acl}
| | @{acl_list} = | Create List | ${0}
| | Set Acl List For Interface | ${dut} | ${dut_if} | ${acl_apply_type}
| | ... | ${acl_list}