1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
|
# Copyright (c) 2017 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/performance.robot
| Resource | resources/libraries/robot/snat.robot
| Resource | resources/libraries/robot/traffic.robot
| ...
| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
| ... | NIC_Intel-X520-DA2 | ETH | IP4FWD | FEATURE | SNAT | BASE
| ...
| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model
| ... | L3 | Intel-X520-DA2
| Suite Teardown | 3-node Performance Suite Teardown
| ...
| Test Setup | Performance test setup
| ...
| Documentation | *SNAT performance test cases*
| ...
| ... | *High level description*
| ...
| ... | - NDR and PDR tests
| ... | - 3-node topology, TG-DUT1-DUT2-TG, SNAT is enabled between DUTs.
| ... | - Cores / threads: 1t1c and 2t2c
| ... | - Framesize: 64B, 1518B, IMIX
| ... | - Packet: ETH / IP(src, dst) / UDP(src_port, dst_port) / payload
| ...
| ... | *Low level description*
| ...
| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
| ... | with single links between nodes.
| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4
| ... | routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2
| ... | tested with 2p10GE NIC X520 Niantic by Intel.
| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
| ... | of packets transmitted. NDR and PDR are discovered for different
| ... | Ethernet L2 frame sizes using either binary search or linear search
| ... | algorithms with configured starting rate and final step that determines
| ... | throughput measurement resolution. Test packets are generated by TG on
| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
| ... | (flow-group per direction, one flow per flow-group) with all packets
| ... | containing Ethernet header, IPv4 header with UDP header and static
| ... | payload. MAC addresses are matching MAC addresses of the TG node
| ... | interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
*** Variables ***
# X520-DA2 bandwidth limit
| ${s_limit} | ${10000000000}
*** Test Cases ***
| tc01-64B-1t1c-ethip4-ip4base-snat-1u-1p-ndrdisc
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\
| | ... | 1 receive queue per NIC port. SNAT is configured between DUTs -\
| | ... | 1 user and 1 port (session) per user.
| | ... | [Ver] Find NDR for 64 Byte frames using binary search start at 10GE\
| | ... | linerate, step 100kpps.
| | ...
| | [Teardown] | Run keywords | Performance test teardown | ${min_rate}pps
| | ... | ${framesize} | 3-node-IPv4-SNAT-1u-1p
| | ... | AND | Show SNAT verbose | ${dut1}
| | ... | AND | Show SNAT verbose | ${dut2}
| | ...
| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC
| | ...
| | ${framesize}= | Set Variable | ${64}
| | ${min_rate}= | Set Variable | ${100000}
| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
| | ${binary_min}= | Set Variable | ${min_rate}
| | ${binary_max}= | Set Variable | ${max_rate}
| | ${threshold}= | Set Variable | ${min_rate}
| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
| | And Add PCI devices to DUTs from 3-node single link topology
| | And Add No Multi Seg to all DUTs
| | And Add SNAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | When SNAT is initialized in a 3-node circular topology
| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
| | ... | ${binary_max} | 3-node-IPv4-SNAT-1u-1p | ${min_rate} | ${max_rate}
| | ... | ${threshold}
| tc02-64B-1t1c-ethip4-ip4base-snat-1u-1p-pdrdisc
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\
| | ... | 1 receive queue per NIC port. SNAT is configured between DUTs -\
| | ... | 1 user and 1 port (session) per user.
| | ... | [Ver] Find PDR for 64 Byte frames using binary search start at 10GE\
| | ... | linerate, step 100kpps.
| | ...
| | [Teardown] | Performance test teardown | ${min_rate}pps | ${framesize}
| | ... | 3-node-IPv4-SNAT-1u-1p
| | ...
| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
| | ...
| | ${framesize}= | Set Variable | ${64}
| | ${min_rate}= | Set Variable | ${100000}
| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
| | ${binary_min}= | Set Variable | ${min_rate}
| | ${binary_max}= | Set Variable | ${max_rate}
| | ${threshold}= | Set Variable | ${min_rate}
| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
| | And Add PCI devices to DUTs from 3-node single link topology
| | And Add No Multi Seg to all DUTs
| | And Add SNAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | When SNAT is initialized in a 3-node circular topology
| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
| | ... | ${binary_max} | 3-node-IPv4-SNAT-1u-1p | ${min_rate} | ${max_rate}
| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
| | ... | ${perf_pdr_loss_acceptance_type}
| tc03-1518B-1t1c-ethip4-ip4base-snat-1u-1p-ndrdisc
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\
| | ... | 1 receive queue per NIC port. SNAT is configured between DUTs -\
| | ... | 1 user and 1 port (session) per user.
| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
| | ... | linerate, step 100kpps.
| | ...
| | [Teardown] | Run keywords | Performance test teardown | ${min_rate}pps
| | ... | ${framesize} | 3-node-IPv4-SNAT-1u-1p
| | ... | AND | Show SNAT verbose | ${dut1}
| | ... | AND | Show SNAT verbose | ${dut2}
| | ...
| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC
| | ...
| | ${framesize}= | Set Variable | ${1518}
| | ${min_rate}= | Set Variable | ${100000}
| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
| | ${binary_min}= | Set Variable | ${min_rate}
| | ${binary_max}= | Set Variable | ${max_rate}
| | ${threshold}= | Set Variable | ${min_rate}
| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
| | And Add PCI devices to DUTs from 3-node single link topology
| | And Add No Multi Seg to all DUTs
| | And Add SNAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | When SNAT is initialized in a 3-node circular topology
| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
| | ... | ${binary_max} | 3-node-IPv4-SNAT-1u-1p | ${min_rate} | ${max_rate}
| | ... | ${threshold}
| tc04-1518B-1t1c-ethip4-ip4base-snat-1u-1p-pdrdisc
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\
| | ... | 1 receive queue per NIC port. SNAT is configured between DUTs -\
| | ... | 1 user and 1 port (session) per user.
| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
| | ... | linerate, step 100kpps.
| | ...
| | [Teardown] | Performance test teardown | ${min_rate}pps | ${framesize}
| | ... | 3-node-IPv4-SNAT-1u-1p
| | ...
| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
| | ...
| | ${framesize}= | Set Variable | ${1518}
| | ${min_rate}= | Set Variable | ${100000}
| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
| | ${binary_min}= | Set Variable | ${min_rate}
| | ${binary_max}= | Set Variable | ${max_rate}
| | ${threshold}= | Set Variable | ${min_rate}
| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
| | And Add PCI devices to DUTs from 3-node single link topology
| | And Add No Multi Seg to all DUTs
| | And Add SNAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | When SNAT is initialized in a 3-node circular topology
| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
| | ... | ${binary_max} | 3-node-IPv4-SNAT-1u-1p | ${min_rate} | ${max_rate}
| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
| | ... | ${perf_pdr_loss_acceptance_type}
| tc05-IMIX-1t1c-ethip4-ip4base-snat-1u-1p-ndrdisc
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\
| | ... | 1 receive queue per NIC port. SNAT is configured between DUTs -\
| | ... | 1 user and 1 port (session) per user.
| | ... | [Ver] Find NDR for IMIX frames using binary search start at 10GE\
| | ... | linerate, step 100kpps.
| | ...
| | [Teardown] | Run keywords | Performance test teardown | ${min_rate}pps
| | ... | ${framesize} | 3-node-IPv4-SNAT-1u-1p
| | ... | AND | Show SNAT verbose | ${dut1}
| | ... | AND | Show SNAT verbose | ${dut2}
| | ...
| | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC
| | ...
| | ${framesize}= | Set Variable | IMIX_v4_1
| | ${min_rate}= | Set Variable | ${100000}
| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
| | ${binary_min}= | Set Variable | ${min_rate}
| | ${binary_max}= | Set Variable | ${max_rate}
| | ${threshold}= | Set Variable | ${min_rate}
| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
| | And Add PCI devices to DUTs from 3-node single link topology
| | And Add No Multi Seg to all DUTs
| | And Add SNAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | When SNAT is initialized in a 3-node circular topology
| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
| | ... | ${binary_max} | 3-node-IPv4-SNAT-1u-1p | ${min_rate} | ${max_rate}
| | ... | ${threshold}
| tc06-IMIX-1t1c-ethip4-ip4base-snat-1u-1p-pdrdisc
| | [Documentation]
| | ... | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core,\
| | ... | 1 receive queue per NIC port. SNAT is configured between DUTs -\
| | ... | 1 user and 1 port (session) per user.
| | ... | [Ver] Find PDR for IMIX frames using binary search start at 10GE\
| | ... | linerate, step 100kpps.
| | ...
| | [Teardown] | Performance test teardown | ${min_rate}pps | ${framesize}
| | ... | 3-node-IPv4-SNAT-1u-1p
| | ...
| | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
| | ...
| | ${framesize}= | Set Variable | IMIX_v4_1
| | ${min_rate}= | Set Variable | ${100000}
| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
| | ${binary_min}= | Set Variable | ${min_rate}
| | ${binary_max}= | Set Variable | ${max_rate}
| | ${threshold}= | Set Variable | ${min_rate}
| | Given Add '1' worker threads and rxqueues '1' in 3-node single-link topo
| | And Add PCI devices to DUTs from 3-node single link topology
| | And Add No Multi Seg to all DUTs
| | And Add SNAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
| | When SNAT is initialized in a 3-node circular topology
| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
| | ... | ${binary_max} | 3-node-IPv4-SNAT-1u-1p | ${min_rate} | ${max_rate}
| | ... | ${threshold} | ${perf_pdr_loss_acceptance}
| | ... | ${perf_pdr_loss_acceptance_type}
|
