blob: e320c46f608ef86687656f59003361d2de1d267d (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
|
# Copyright (c) 2016 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Variables ***
# Node and interface to run tests on.
| ${node}= | ${nodes['DUT1']}
| ${interface}= | ${node['interfaces'].values()[0]['name']}
# Configuration which will be set and verified during tests.
| @{ipv4_address_mask}= | 192.168.0.2 | 255.255.255.0
| @{ipv4_address_prefix}= | 192.168.0.3 | ${16}
| @{ipv4_neighbor}= | 192.168.0.4 | 08:00:27:c0:5d:37
| &{ipv4_settings}= | enabled=${True} | forwarding=${True} | mtu=${9000}
| @{ipv6_address}= | 10::10 | ${64}
| @{ipv6_neighbor}= | 10::11 | 08:00:27:c0:5d:37
| &{ipv6_settings}= | enabled=${True} | forwarding=${True} | mtu=${9000}
| ... | dup-addr-detect-transmits=${5}
| &{ethernet}= | mtu=${9000}
| &{routing}= | vrf-id=${27}
| &{vxlan_settings}= | src=10.0.1.20 | dst=10.0.3.20 | vni=${1000}
| ... | encap-vrf-id=${1000}
*** Settings ***
| Resource | resources/libraries/robot/default.robot
| Resource | resources/libraries/robot/honeycomb/honeycomb.robot
| Resource | resources/libraries/robot/honeycomb/interfaces.robot
| Suite Setup | Run keywords | Setup all DUTs before test | AND
| ... | Setup Honeycomb service on DUTs | ${node}
| Documentation | *Honeycomb interface management test suite.*
| ...
| ... | Test suite uses the first interface of the first DUT node.
*** Test Cases ***
| Honeycomb configures and reads interface state
| | [Documentation] | Check if Honeycomb API can modify the admin state of\
| | ... | VPP interfaces.
| | [Tags] | honeycomb_sanity
| | Given Interface state is | ${node} | ${interface} | down
| | When Honeycomb sets interface state | ${node} | ${interface} | up
| | Then Interface state from Honeycomb should be
| | ... | ${node} | ${interface} | up
| | And Interface state from VAT should be | ${node} | ${interface} | up
| | When Honeycomb sets interface state | ${node} | ${interface} | down
| | Then Interface state from Honeycomb should be
| | ... | ${node} | ${interface} | down
| | And Interface state from VAT should be | ${node} | ${interface} | down
| Honeycomb modifies interface configuration - ipv4
| | [Documentation] | Check if Honeycomb API can configure interfaces for ipv4.
| | [Tags] | honeycomb_sanity
| | When Honeycomb sets interface ipv4 configuration
| | ... | ${node} | ${interface} | @{ipv4_address_mask} | @{ipv4_neighbor}
| | ... | ${ipv4_settings}
| | Then IPv4 config from Honeycomb should be
| | ... | ${node} | ${interface} | @{ipv4_address_mask} | @{ipv4_neighbor}
| | ... | ${ipv4_settings}
| | And IPv4 config from VAT should be
| | ... | ${node} | ${interface} | @{ipv4_address_mask}
| | When Honeycomb sets interface ipv4 address with prefix
| | ... | ${node} | ${interface} | @{ipv4_address_prefix}
| | Then IPv4 config from Honeycomb should be
| | ... | ${node} | ${interface} | @{ipv4_address_prefix} | @{ipv4_neighbor}
| | ... | ${ipv4_settings}
| | And IPv4 config from VAT should be
| | ... | ${node} | ${interface} | @{ipv4_address_prefix}
| Honeycomb modifies interface configuration - ipv6
| | [Documentation] | Check if Honeycomb API can configure interfaces for ipv6.
| | [Tags] | honeycomb_sanity
| | When Honeycomb sets interface ipv6 configuration
| | ... | ${node} | ${interface} | @{ipv6_address} | @{ipv6_neighbor}
| | ... | ${ipv6_settings}
| | Then IPv6 config from Honeycomb should be
| | ... | ${node} | ${interface} | @{ipv6_address} | @{ipv6_neighbor}
| | ... | ${ipv6_settings}
| | And IPv6 config from VAT should be
| | ... | ${node} | ${interface} | @{ipv6_address}
| Honeycomb modifies interface configuration - ethernet,routing
| | [Documentation] | Check if Honeycomb API can configure interface ethernet\
| | ... | and routing settings.
| | [Tags] | honeycomb_sanity
| | When Honeycomb sets interface ethernet and routing configuration
| | ... | ${node} | ${interface} | ${ethernet} | ${routing}
| | Then Interface ethernet and routing configuration from Honeycomb should be
| | ... | ${node} | ${interface} | ${ethernet} | ${routing}
| | And Interface ethernet and routing configuration from VAT should be
| | ... | ${node} | ${interface} | ${ethernet['mtu']} | ${routing['vrf-id']}
|
